7-12
INSPECTION AND MAINTENANCE
79K21-03E
Replace the Oil Filter2.4 L engine
78K055
1) Using an oil filter wrench, turn the oil fil-
ter counterclockwise and remove it.
2) Using a clean rag, wipe off the mount-
ing surface on the engine where the
new filter will be seated.
3) Smear a little engine oil around the rub-
ber gasket of the new oil filter.
4) Screw on the new filter by hand until the
filter gasket contacts the mounting sur-
face.
54G093
(1) Oil filter
(2) 3/4 turn
5) Tighten the filter 3/4 turn from the point
of contact with the mounting surface (or
to the specified torque) using an oil filter
wrench.
6) Reinstall the engine under cover.NOTE:
When it is difficult to remove the oil filter,
we recommend you take your vehicle to
your SUZUKI dealer for oil filter replace-
ment.
For 3.2 L engine, since special proce-
dures are required, we recommend you
take your vehicle to your SUZUKI dealer
for oil filter replacement.
Refill with Oil and Check for Leaks1) Pour oil through the filler hole and
install the filler cap.
For the approximate capacity of the oil,
refer to the “Capacities” item in the
“SPECIFICATIONS” section.
2) Start the engine and look carefully for
leaks at the oil filter and drain plug. Run
the engine at various speeds for at least
5 minutes.
3) Stop the engine and wait about 5 min-
utes. Check the oil level again and add
oil if necessary. Check for leaks again.
CAUTION
To tighten the oil filter properly, it is
important to accurately identify the
position at which the filter gasket
first contacts the mounting surface.
EXAMPLE
Tightening torque specification
14 Nm (10.1 lb-ft, 1.4 kg-m)
CAUTION
To prevent oil leakage, make sure
that the oil filter is tight, but do not
overtighten it.
CAUTION
When replacing the oil filter, it is rec-
ommended that you use a genuine
SUZUKI replacement filter. If you use
an after-market filter, make sure it is
of equivalent quality and carefully fol-
low the manufacturer’s instructions
and precautions.
Engine Oil and Filter: 1, 2
12-4SPECIFICATIONS
79K21-03E
ITEM: Steering
Toe-in Front 0 ± 2 mm (0 ± 0.08 in.)
Rear 6 ± 2 mm (0.24 ± 0.08 in.)
Camber angle Front 0° 00’
Rear –1° 15’ ± 40’
Caster angle Front 2° 30’
ITEM: Capacities (approx.)
Coolant 2.4 L 7.3 L (15.4 US pt)
3.2 L 9.5 L (20.1 US pt)
Fuel tank 66 L (17.4 US gal)
Engine oil (replaced with filter) 2.4 L 4.8 L (10.1 US pt)
3.2 L 6.0 L (12.7 US pt)
Transmission oil M/T 1.9 L (4.0 US pt)
A/T 2.4 L 2.5 L (5.3 US pt)
3.2 L 3.0 L (6.3 US pt)
Differential gear oil Front 0.95 L (2.0 US pt)
Rear2WD 5M/T, 5A/T 1.1 L (2.3 US pt)
4A/T 0.8 L (1.7 US pt)
4WD 0.8 L (1.7 US pt)
Transfer gear box oil with a transfer switch 1.5 L (3.2 US pt)
without a transfer switch 1.6 L (3.4 US pt)
Extension case oil 0.47 L (1.0 US pt)
