2012 SUBARU IMPREZA WRX STI start stop button
[x] Cancel search: start stop buttonPage 10 of 463
15
14
Getting
Started Instrument
Panel Gauges
Personalize Controls While
OperatingSafety / In Case
of Emergency Additional
Information
15
GetGttintigStartedInsItrument PanelGauGgesPerPsonalilizeControlsWhiWhile lOperatingSafSfetyt / /In ICasCe of EmergencyAddAdditiiional lInformation
Controls
Controls
Illumination
Brightness Control
While the light switch
is on, rotate the dial downward to dim
the instrument panel
illumination. Rotate the dial upward to make the illumination
brighter. When the dial is fully rotated
upward, the instrument panel illumination
becomes full bright.
Windshield WipersTo turn on the wipers, press the wiper control lever down one level for intermittent,
U X P M F W F M T G P S M P X
P S U I S F F M F W F M T G P S I J H I T Q F F E 3 F U V S O U I F M F W F S U P U I F i 0 ' ' w
position to stop the wipers. For a single wipe, pull the lever toward you. To spray
washer fluid, press and hold the button at the end of the lever.
To operate the rear wiper, rotate the end of the knob upward to the intermittent,
continuous, or wash position. When the rear wiper is off, rotate the knob downward
to wash and wipe the rear window.Daytime Running LightsDaytime running lights are standard on your vehicle. Only a reduced brightness high
beam will be automatically turned on when the engine has started and the parking
C S B L F J T G V M M Z S F M F B T F E B O E U I F M J H I U T X J U D I J T J O U I F i 0 ' ' w P S i
w Q P T J U J P O 5 I F
brightness of the illumination of the high beam headlights is reduced by the daytime
running light system. You must always switch on your headlights when it’s dark
outside by turning the light switch to the
position.
Light Controls
Turns on instrument panel lights,
taillights, parking lights and
license plate lights.
Turns on headlights, instrument
panel illumination, parking lights,
taillights and license plate lights. Turns on
fog lights
(if equipped).
Push up for right
turn signal.
Push down for
left turn signal.
OFF123
INT.
LOW
HIGH
Headlight Beam
Leveler
(if equipped)
Your vehicle’s High-Intensity
Discharge (HID) headlights
generate more light than
conventional halogen
headlights. Therefore, a driver
of an oncoming vehicle may
experience too much glare
when your headlight beam
height adjustment is high
because the vehicle is carrying
a heavy load. The headlight
beam leveler can be used to
adjust beam height to avoid
such a condition. To lower the
beam, turn the knob to the
higher numbers.
Page 12 of 463
19
18
Getting
Started Instrument
Panel Gauges
Personalize Controls While
OperatingSafety / In Case
of Emergency Additional
Information
19
GetGttintigStartedInsItrument PanelGauGgesPerPsonalilizeControlsWhiWhile lOperatingSafSfetyt / /In ICasCe of EmergencyAddAdditiiional lInformation
Controls
Controls
1
AM/FM Stereo with Single
Disc CD/MP3/WMA PlayerRadio Functions1. Power / Volume Control
Press the power / volume control knob
for on or off; rotate the knob to control
the volume.
2. Bass, Middle, Treble, Fader and Balance
& B D I Q S F T T P G U I F i 5 6 / & 5 3 " $ , $ ) w
button will cycle you through Bass,
Midrange, Treble, Fade or Balance. Rotate
U I F i 5 6 / & 5 3 " $ , $ ) w L O P C U P B E K V T U
the desired level.
3. FM / AM 1 S F T T U I F i ' . " . w C V U U P O U P D I P P T F
FM1, FM2, FM3 or AM reception.
4. Tune / Track 3 P U B U F U I F i 5 6 / & 5 3 " $ , $ ) w
knob clockwise to increase the
tuning frequency; rotate the knob
counterclockwise to decrease it. 5. Seek
1 S F T T U I F S J H I U P S M F G U B S S P X P G U I F i 4 & & , w
button to pick up the next highest or
lowest frequency.
6. Presets You can save up to six favorite stations
G P S F B D I C B O E o ' .
' .
' . B O E " .
Select a frequency and press one of the
preset buttons until a confirmation beep
is heard.
7. Satellite Radio An optional satellite radio tuner and
antenna can be connected to this audio
unit. You can hear satellite radio programs
C Z Q S F T T J O H U I F i 4 " 5 w C V U U P O B G U F S
connecting optional equipment. To receive
satellite radio service, it is necessary to
enter into a separate contract with a
satellite radio provider. 8. PTY / CAT
1 S F T T U I F i 1 5 : $ " 5 w C V U U P O U P
change to program type selection
mode. The PTY group that you are
currently listening to is displayed
for 10 seconds.
CD Player Functions 9. Load Insert a disc into the slot. The CD
will automatically be drawn in and
will begin play at the first track.
10. Play CD 1 S F T T U I F i $ % " 6 9 w C V U U P O B O E
playback will begin.
11. Repeat / Random 1 S F T T U I F i 3 1 5 3 % . w C V U U P O P O D F to repeat the current track; press
twice to repeat the current folder.
1 S F T T B O E I P M E U I F i 3 1 5 3 % . w
button once to randomize all
tracks in a folder; press twice to
randomize the entire disc.
12. Eject Press the button to eject the disc.
13. Forward / Reverse 3 P U B U F U I F i 5 6 / & 5 3 " $ , $ ) w
knob clockwise to skip to the
beginning of the next track; rotate
the knob counterclockwise to
skip to the beginning of the
current track. Rotate the knob
counterclockwise again to go to
the previous selection. 14. Fast Forward / Fast Reverse
Press and hold the right arrow
P G U I F i 4 & & , w C V U U P O G P S N P S F
than one second to fast forward.
Release the button to stop. To fast
reverse, press and hold the left
arrow for more than one second
and release the button to stop.
15. Scan 1 S F T T U I F i 4 $ " / w C V U U P O U P C F H J O
previewing the first 10 seconds
P G F B D I U S B D L P O U I F E J T D / P S N B M
playback will resume after all
tracks have been scanned. Press
U I F i 4 $ " / w C V U U P O B H B J O U P T U P Q
scanning and listen to the track
being previewed.
MP3/WMA Formatted CD
Player Functions16. Folder Selection Press the up arrow of the
i ' 0 - % & 3 w C V U U P O U P T F M F D U U I F
next folder. Press the down arrow
to go back to the first music file.
Quickly press the down arrow
again to go back to the
previous folder.
17. Page Scroll 1 S F T T U I F i 5 & 9 5 w C V U U P O U P T F M F D U
title display. Press and hold again
to scroll through the title, 8
characters at a time up to a
maximum of 64 characters.
18. Display 1 S F T T B O E I P M E U I F i 5 & 9 5 w C V U U P O
during playback to change the
display to show the play time, disc
title, artist name and track title. If
the disc is formatted with MP3/
8 . " T
Q S F T T U I F i 5 & 9 5 w C V U U P O U P
change the display to show play
time, folder name and file name.
11
9
3
8
15
5
5
13
18
7
16
17
14
14
10
2
4
6
12
Page 150 of 463
Black plate (104,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
2-16
Keys and doors
& If you have accidentally trig-
gered the alarm system! To stop the alarm
Do any of the following operations:
. Press any button on the remote trans-
mitter.
. Turn the ignition switch to the “ON”
position.NOTEOnly registered keys will stop the
alarm. If the immobilizer transponder
is not registered, the alarm will not
stop.& Arming the system! To arm the system using remote
transmitter
1. Close all windows.
2. Remove the key from the ignition
switch.
3. Open the doors and get out of the
vehicle.
4. Make sure that the engine hood (and
the trunk lid on the 4-door) are locked.
5. Close all doors (and the rear gate on
the 5-door).
: Press to Arm the system.: Press to Disarm the system.
6. Briefly press the “
”button (for less
than 2 seconds). All doors (and the rear
gate on the 5-door) will lock, an electronic
chirp will sound once, the turn signal lights will flash once, and the security indicator
light will start flashing rapidly. After rapid
flashing for 30 seconds (standby time), the
indicator lights will then flash slowly (twice
approximately every 2 seconds), indicat-
ing that the system has been armed for
surveillance.
If any of the doors, (rear gate or trunk lid)
is not fully closed, an electronic chirp
sounds five times, the turn signal lights
flash five times to alert you that the doors
(or the rear gate) are not properly closed.
When you close the door, the system will
automatically arm and doors will automa-
tically lock.
!
To arm the system using power
door locking switches
1. Close all windows.
2. Remove the key from the ignition
switch.
3. Open the doors and get out of the
vehicle.
4. Make sure that the engine hood is
locked.
5. Close the doors (and the rear gate on
the 5-door) but leave only the driver ’s door
or the front passenger ’s door open.
Page 238 of 463
Black plate (194,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
5-10
Audio
FM/AM radio operation& FM/AM selectionType A audioType B audioPress the “FM/AM”button when the radio
is off to turn on the radio.
Press the “FM/AM”button when the radio
is on to select the preferred reception
mode.
Each brief press of the “FM/AM”button
changes the radio in the following se-
quence starting from the last radio band
with you selected.
& Tuning! Manual tuningType A audioType B audioTurn the “TUNE/TRACK/CH ”dial clock-
wise to increase the tuning frequency and
turn the “TUNE/TRACK/CH ”dial counter-
clockwise to decrease it.
Each time the dial is turned, the frequency
interval can be changed between 10 kHz
in the AM mode and 0.2 MHz in the FM
mode.
! Stereo indicator
The stereo indicator “ST”will illuminate
when an FM stereo broadcast is received. !
Seek tuning (SEEK)
Type A audio:
Seek upSeek downType B audio:Seek upSeek downIf you press the “
”or “
”side of the
“SEEK ”button briefly, the radio will auto-
matically search for a receivable station
and stop at the first one it finds.
This function may not be available when
radio signals are weak. When this hap-
pens, perform manual tuning to select the
desired station.
Page 246 of 463
Black plate (202,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
5-18
Audio
! Loading all the magazine (full disc
loading mode)
1. If you press and hold the
button,
the player will produce beep sound and
will enter the full disc loading mode.
2. When the disc number indicator
flashes and “ALL LOAD” indicator illumi-
nates, insert a disc within 15 seconds. If a
disc is successfully loaded during this
period, the disc number indicator will stop
blinking and will steadily light.
3. When the loading of a disc is com-
plete, the next disc number indicator will
blink. Then repeat step 2.
4. When the magazine is filled with discs
by repeating steps 2 and 3, the player will
start playback of the discs, beginning with
the one inserted first.
If you fail to insert any disc during each 15
seconds interval, the full disc loading
mode will be canceled, and the player will
start playback of the disc inserted first.
& How to insert a CD (type B)Hold the disc with a finger in the center
hole while gripping the edge of the disc,
then insert it into the slot (with the label
side up) and the player will automatically
pull the disc into position.
NOTEDO NOT INSERT TWO DISCS INTO THE
DISC INSERTION SLOT AT THE SAME
TIME.&How to play back a CD! When there is no CD inserted
Properly insert a CD. Refer to “How to
insert a CD(s) (type A) ”F 5-17/ “How to
insert a CD (type B) ”F 5-18.
When a CD is loaded, the player will start
playback of the CD, beginning with the
first track.
! When there are CDs loaded (type A)
Press the preferred disc select button
(from
to
). If a disc is loaded
in any slot, the corresponding disc number
indicator will be constantly illuminated.
The player will then start playback of the
selected CD, beginning with the first track.
If a disc that the player cannot read has
been loaded, the player will display the
message “CHECK DISC ”.
! When CD is in the player (type B)
Each brief press of the
button
changes the modes in the following
sequence.
When the CD mode is selected, the player
will start playback.& To select a track from the
beginningType A audioType B audioTurn the “TUNE/TRACK/CH ”dial clock-
wise to skip to the beginning of the next
track/file. Each time the dial is turned, the
indicated track/file number will increase.
Turn the “TUNE/TRACK/CH ”dial counter-
clockwise to skip to the beginning of the
current track/file. Each time the dial is
turned, the indicated track/file number will
decrease.
Page 247 of 463
Black plate (203,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
NOTEWith an MP3, WMA or AAC (type B
audio):
. Skipping past the last track/file will
take you back to the first track/file in
the folder.
. Skipping past the first track/file will
take you to the last track/file in the
folder.& Fast-forwarding and rewind-
ingType A audio:Fast-forwardRewindType B audio:Fast-forwardRewind
Press and hold the “
”button to fast-
forward the track. Release the button to
stop fast-forwarding.
Press and hold the “”button to rewind
the track. Release the button to stop
rewinding.
NOTE. If you fast-forward to the end of the
last track, fast-forwarding will stop and
the player will start playback beginning
with the first track. For an MP3, WMA or
AAC (type B audio) folder, the player
will start playback beginning with the
first track of the next folder.
. If you rewind to the beginning of the
first track, rewinding will stop and the
player will start playback. For an MP3,
WMA or AAC (type B audio) folder, the
player will start playback beginning
with the first track of the current folder.& RepeatingType A audioType B audioTo repeat a track/file, briefly press the
“RPT/RDM ”button while the track/file is playing.
Each time you briefly press the button, the
mode changes in the following se-
quences.
Type A audio:
Type B audio:NOTE.
The “RPT ”indication refers to the
repeat playback of a single track. It
repeats the track that is playing.
. The “F-RPT ”indication refers to the
repeat playback of a folder. It repeats
the all of the tracks in the folder. It is
possible to select the function when
the MP3/WMA/AAC format track is
playing.
. The “D-RPT ”indication refers to the
repeat playback of a disc. It repeats the
tracks on the CD. It is only possible to
select this function for type A audio.
To cancel the track/file repeat-play mode,
briefly press the “RPT/RDM”button and
select CANCEL. The “RPT”indication will
turn off, and the normal playback mode
Audio
5-19
– CONTINUED –
5
Page 300 of 463
Black plate (260,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
7-10
Starting and operating
Stopping the engineThe ignition switch should be turned off
only when the vehicle is stopped and the
engine is idling.
WARNING
Do not stop the engine when the
vehicle is moving. This will cause
loss of power to the power steering
and the brake booster, making steer-
ing and braking more difficult. It
could also result in accidental acti-
vation of the “LOCK ”position on the
ignition switch, causing the steering
wheel to lock.
Remote engine start system
(dealer option)
WARNING
. Do not start the engine using the
remote start system in an en-
closed environment (e.g., in a
closed garage). Prolonged opera-
tion of a motor vehicle in an
enclosed environment can cause
a harmful build-up of Carbon
Monoxide. Carbon Monoxide is
harmful to your health. Exposure
to high levels of Carbon Monox-
ide can cause headaches, dizzi-
ness or in extreme cases uncon-
sciousness and/or death.
. Before performing any servicing
of the vehicle, temporarily place
the remote engine start system in
service mode to prevent the
system from unexpectedly start-
ing the engine.
& Starting your vehicleThe remote engine start system is acti-
vated by pressing the “
”button twice
within 3 seconds on your remote engine
start transmitter. The system will check
certain pre-conditions before starting, and
if all safety parameters are correct, the
engine will start within 5 seconds. While
the vehicle is operating via remote engine
start, the vehicle ’s power window features
will be disabled. Also, the system has a
timer and will shut down after 15 minutes if
you do not operate the vehicle. Press and
hold the “
”button for 2 seconds again to
turn the vehicle off. If the vehicle’ s starter
cranks but does not start or starts and
stalls, the remote engine start system will
power off then attempt to start the vehicle
Page 301 of 463
Black plate (261,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
an additional four times. If the vehicle fails
to start after the additional attempts, the
remote engine start system will abort and
return to a non-activated state.& Remote start safety featuresFor safety and security reasons, the
system will fail to start and beep the horn
twice or shut down the engine during
remote start operation if any of the
following conditions occur.
. The brake pedal is depressed before
the vehicle ignition switch is turned “on”.
. The key was already in the ignition
switch.
. The engine hood is opened.
. The vehicle’ s engine idle speed has
reached a level over 3,000 rpm.
. The alarm is triggered by opening a
door or the rear gate.NOTE. The security indicator light on the
combination meter will stop flashing
while under remote engine start opera-
tion, but the vehicle is still protected.
. If the vehicle is entered during
remote engine start operation, the
system will not record entry in the
alarm history.
& Entering the vehicle while it
is running via remote start1. Unlock the vehicle doors using the
remote keyless entry system. If the vehi-
cle’s doors are unlocked manually using
the key, the vehicle’ s alarm system will
trigger and the remote engine start system
will turn off. Inserting the key into the
ignition switch and turning it to the “ON”
position or pressing the unlock button “
”
on the remote keyless entry transmitter
will disarm the alarm system. Refer to
“Alarm system ”F 2-15.
2. Enter the vehicle. Do not depress the
brake pedal.
3. Insert the key into the ignition switch
and turn to the “ON”position. If the ignition
switch is accidentally turned to the
“START ”position, the system ’s “starter
anti-grind” feature will prevent the starter
from re-cranking.
4. Depress the brake pedal. The remote
starter disengages, the vehicle’ s power
window features are re-enabled and the
vehicle will operate normally.
& Entering the vehicle follow-
ing remote engine start shut-
downAn alarm trigger may occur if the vehicle is
opened by the remote keyless entry transmitter within a few seconds immedi-
ately following remote engine start shut-
down.
&
Pre-heating or pre-cooling
the interior of the vehicleBefore exiting the vehicle, set the tem-
perature controls to the desired setting
and operation. After the system starts the
vehicle, the heater or air-conditioning will
activate and heat or cool the interior to
your setting.&Service modeIn service mode, the remote start function
is temporarily disabled to prevent the
system from unexpectedly starting the
engine while being serviced.
! To engage the service mode
Turntheignitionswitchtothe “ON ”
position, depress and hold the brake
pedal, then press and release the “
”
button on the remote engine start trans-
mitter three times. The system will pause
for 1 second and then flash the turn signal
lights and honk the horn three times
indicating that the system is in service
mode. When attempting to activate the
remote start system while in service
mode, the turn signal lights will flash and
the horn will honk two times and will not
Starting and operating
7-11
– CONTINUED –
7