2012 SSANGYONG KORANDO engine

04-24
6) Power Relay Control
(1) OFF to engine starting
(2) ACC to IGN

04-258712-03
(3) IGN to starting
(4) IGN/engine ON to ACC
(5) IGN/engine ON to OFF

04-26
7) START Switch Control
Status Turning on conditions
OFF IGN OFF, IGN ON & engine ON
Green Engine can be started by START switch operation/Engine is cranking (IGN OFF &
brake switch ON, ACC ON & brake switch ON, IGN ON & brake switch ON, etc.)
Yellow ACC ON
Red IGN ON & engine OFF or error
Ignition status indicator on START switch ▶
(1) START switch indicator
START switch indicator output ▶
* When an error occurs, the indicator is illuminated for 0.5 sec. and goes off for 0.5 sec., and
then flashes for 10 sec.
* When all the doors are closed with B+, the LED does not flash.
Start switch indicator control ▶
Door coupled function -
1. When the driver's door is opened, the switch indicator comes on (the indicator remains on
while the door is open).
2. The indicator goes off immediately when the interior lamps are turned off.
3. The indicator goes off after the driver's door is closed and 10 sec. ON timer is activated.
4. The indicator is reset when the driver's door is opened.
Tail lamp coupled function -
Ignition
statusPower OFF
ACC ON IGN ON
(STOP)IGN ON
START ErrorRemark
Door
CloseDoor
Open
Indica-
tion
Indicator
statusOFF OFF Orange Red OFF Green Red
OFF OFF ON ON OFF ON Flashing
Illumina-
tionOFF TIME
Controlled by SKMLED
Engine START/STOP

04-278712-03
8) SKM Warning Control
(1) Smart key not found warning (Key out warning)
If no verified smart key is identified as being in the vehicle with IGN ON or ACC ON, the SKM sends the
signal, which identifies that there is no verified key inside the vehicle, to the BCM and instrument cluster
through the BCAN (Smart key not found warning). This warning continues for up to 10 sec. until the
warning condition is deactivated.
The SKM stops the warning immediately after the warning condition is deactivated.
Initial condition:
& & &
Operation by driver
<006b009600960099009a006100470063006b009600960099009a004700960097008c00950047008c009f008a008c0097009b0047008b00990090009d008c0099004e009a0047008b00960096009900650047004d00470063007b008800900093008e008800
9b008c004700960097008c0095006502e70047006300680093>l doors closed> &

SKM operation -
-
-
The SKM starts to identify a smart key by using the interior antenna after confirming that all the
doors are closed through CAN communication.
If no smart key is found it sends the signal for [Smart key not found warning].
* No cyclic smart key searching after transmission
If a smart key is found, no operation is performed.
- Smart key not found warning deactivation conditions
If below conditions are met, the SKM sends the signal for [Smart key not found warning]
to deactivate the warning.
: OR OR 1.
2.
3. Smart key not found warning with ACC ON ▶
Smart key not found warning with IGN/ENGINE ON ▶
Initial condition:
& & &
Operation by driver
<006b009600960099006100470063006b009600960099004700960097008c009500650047004d00470063007b008800900093008e0088009b008c004700960097008c00950065004702e7004700630068009300930047008b009600960099009a0047008a00
930096009a008c008b00650047004d00470063007b00880090>lgate closed>
SKM operation -
-
-
The SKM starts to identify a smart key by using the interior antenna if the [Smart key not found
warning] signal is not output.
a. If no smart key is found it sends the signal for [Smart key not found warning].
b. If a smart key is found, no operation is performed.
The SKM searches for a smart key inside the vehicle at 3 sec. intervals while the [Smart key not
found warning] signal is output.
a. If no smart key is found it sends the signal for [Smart key not found warning].
b. If a smart key is found it sends the signal for [Smart key not found warning
deactivation] signal to deactivate the key out warning. 1.
2.

04-298712-03
(4) Smart key battery discharge warning (3) Smart key verification fail warning
When the verification is requested for ignition status change or engine starting and no verified smart key
is in the vehicle, the SKM sends the [smart key verification status] signal, which indicates that the
verification has failed, for up to 10 sec. until the verification fail conditions are deactivated.
Verification fail detection and transmission conditions ▶
When the ignition status is changed after a smart key is verified by the START switch ON input, the
SKM sends the verification status for 10 sec. -Normally, the smart key verification warning is one of the smart key fail conditions. -
Ignition status change
(OFF ->ACC) / (OFF ->IGN)/(ACC ->IGN) / (IGN -> engine ON) *
If above conditions are met again, the SKM re-verifies a smart key and sends the verification status for
another 10 sec.
When the ignition status is changed by the transponder verification while the smart key status is sent
through the BCAN, the SKM sends the smart key verification signal and also sends the transponder
verification signal for 10 sec. -
-
If low smart key battery is detected during the verification process for ignition status change or engine
start, the SKM sends the signal for [smart key battery low voltage warning] to the BCM and instrument
cluster through the BCAN for up to 10 sec. until the warning condition is deactivated.
Smart key battery discharge confirmation and deactivation ▶
If the smart key battery low voltage is confirmed, the SKM sends the smart key battery low voltage
warning signal.
If the smart key battery is in normal condition, the SKM sends the smart key battery low voltage
warning deactivation signal.
The smart key is the last used key. -
-
*
(5) Transponder verification fail warning
If a verified smart key is not found by the key verification process, the SKM sends the information that
indicates the key is not verified to the instrument cluster through the BCAN for up to 10 sec. until the
verification fail condition is deactivated.
The SKM sends the transponder verification warning when the verification has failed with the smart key
inserted into the immobilizer holder. -
Transponder verification fail detection and transmission conditions ▶
When the ignition status is changed after the transponder is verified by the START switch ON input,
the SKM sends the transponder verification status for 10 sec. -

04-30
Ignition status change
(OFF ->ACC) / (OFF ->IGN)/(ACC ->IGN) / (IGN -> engine ON) *
If above conditions are met again, the SKM re-verifies the transponder and sends the verification
status for another 10 sec.
When the ignition status is changed by a smart key verification while the transponder verification is
processed, the SKM sends the signal for [transponder verification fail], and sends the smart key
verification status for 10 sec. -
-
(6) Transmission position warning
When the gear selector lever is in a position other than P or N with IGN ON and engine started, the
SKM sends the [gear position warning] signal to the instrument cluster through the BCAN for up to 10
sec. until the operating conditions are deactivated.
Transmission position warning deactivation ▶
When re-attempting to start with IGN1 ON and transmission in P or N -
(7) SKM error alert
The SKM sends the SKM error alert signal to the instrument cluster through the BCAN for up to 10 sec.
when an in ignition status related error or passive entry system error occurs.
SKM error transmission conditions ▶
When any of the following errors is detected and a DTC is set, the SKM sends the error alert signal for
10 sec.
B+ (power) low voltage
B+ (logic) low voltage
ACC ON fail
ACC OFF fail
IGN1 ON fail
IGN1 OFF fail
IGN2 ON fail
IGN2 OFF fail
Short circuit in START switch 1.
2.
3.
4.
5.
6.
7.
8.
9.
The SKM sends the corresponding signal only once for 10 sec. when any of the above errors is detected
with IGN OFF/ON. It sends the signal again when a new error occurs.

05-58010-01
Previous Current
Ambient temperature also displayed on vehicle with manual A/C control switch
Both SVC and STD class
Previous Current
Warning lamp symbols fulfil ISO standards used on all models
(e.g. 4WD CHECK indicator symbol)
4) Warning lamps according to ISO standards
5) Ambient temperature display
SVC class
This is displayed for 2 seconds when activating winter mode, displayed for 2 seconds when deactivating
winter mode and displayed for 4 seconds when starting engine and driving off (DOT LCD message).
AutomaticAutomatic
Manual
SVC classSVC class
STD class

05-6
SVC class
Previous Current
Changed from figure type to bar graph type.
6) Average fuel economy reset and calibrated automatically when
refilling
7) Instant fuel consumption display changed
8) Pre-warning indicator for engine overheat removed
Both SVC and STD class
Previous Current
Reset by user Reset by user and automatic reset when refilling
9) TDMS logic changed
SVC class
Current
TDMS (Tier Direction Management System) is not displayed when EPS warning lamp comes on.
SVC class STD class
Pre-warning indicator for engine overheat is removed.
EPS warning lampTDMS displayLCD not displayed
EPS warning lamp
comes onLCD screen is not
displayed.