2012 SSANGYONG KORANDO turn signal

01-50000-00
High mounted stop lamp
Rear combination lamp
Vehicle without
spoiler Vehicle with spoiler
License plate lamp
Stop lamp and tail lamp
Rear fog lamp
Turn signal lamp
Backup lamp

02-278410-00
4) Operating Process By Power Supply
(1) Rear wiper relay
(2) Rear fog lamp relay
The rear wiper motor relay is turned on when the rear wiper switch is turned on with the ignition key ON.
This relay is turned off when the rear wiper switch is turned off.
The power is supplied to the ICM no. B6 connector through the SB4 and no. 39.
The power for the rear fog lamp relay is supplied through the memory fuse in the engine compartment
CE box and fuse no. 52 in the interior IP box. This relay is controlled (ON/OFF) by the relay operation
signal which is connected to the no. A11 of the BCM.
The rear fog lamp is turned on when the rear fog lamp switch is turned on with the headlamp turned
on (i.e. IGN2 switch ON).
Turning on the rear fog lamp switch again when the relay is activated turns off the fog lamp.
The rear fog lamps do not come ON when the IGN2 switch is turned to OFF position or the light
switch is OFF.
The rear fog lamp should not automatically come on again if it has been turned off by any methods
other than the rear fog lamp switch. 1.
2.
3.
4.Operating conditions ▶

02-298410-00
(5) Horn relay
The power for the theft deterrent horn relay is supplied to the ICM terminal no. C5 through the battery
SB1 and fuse no. 45 in the interior fuse box.
The relay is operated by the signals from the BCM terminal no. A24. Refer to Conditions For Theft
Deterrent for operating conditions.
(6) Tailgate relay
The power for the tailgate relay is supplied to the ICM terminals no. C10 and no. B5 through the battery
SB1 and fuse no. 42 in the interior fuse box. The relay is operated (i.e. ON/OFF) by the operation signal
from the BCM terminal no. D6.
Deactivation condition ▶
Without SKM
The tailgate open relay is turned OFF immediately after the driver's door is locked or the vehicle
speed becomes 3 km/h or more during its activation.
With SKM
Refer to the section Tailgate of BCM for the operating conditions. -
-

02-30
(7) Shift lock relay
The shift lock relay is used in the models with A/T and receives power through the SB2 and fuse no. 31
in the interior fuse box with the IGN1 turned ON. If the operating conditions are met (stop lamp switch
ON), the battery power is supplied to the ICM terminal no. C1. If the gear mode conditions are met, the
relay is operated by the signals from the terminal no. 10 of the gear selector lever.
(8) Power outlet relay
The power for the power outlet relay is supplied to the ICM terminal no. B10 through the battery SB1
and fuse no. 46 in the interior fuse box. The relay is earthed through the fuse no. 47 in the interior fuse
box and then ICM terminals no. B2 and no. B12 when the ignition key is turned to ACC.

03-6
FunctionSKM
without
BCMSKM
with
BCM
15 Theft deterrent control Theft deterrent mode control in
controlOX
Theft deterrent mode control in smart BCM X O
16 Time lag power
window controlTime lag power window control O O
17 System power sleep
modeSystem power sleep mode control O O
18 Flasher (blinking)
functionLH turn signal control O O
RH turn signal control O O
Hazard warning flasher switch control O O
Hazard warning flasher indicator control X X
Auto hazard warning flasher control O O
Emergency hazard warning flasher control
(coupled with ABS)OO
19 DRL (Daytime Running
Light) controlDRL (Daytime Running Light) control X X
20 Fog lamp control Fog lamp control O O
21 Auto light
control (LIN)Auto light control O O
22 Immobilizer function Key coding and synchronization O X
Challenge O X
CAN information O X
23 Mirror folding/unfolding
controlFolding/unfolding control O O
Auto folding/unfolding control O O
24 Approach (puddle)
lamp control
Approach (puddle) lamp control in BCM without
SKMOX
Approach (puddle) lamp control in BCM with
SKMXO
25 SKM warning buzzer
controlSKM warning buzzer control X O
26 Diagnosis function O O

03-78710-01
3. MAJOR CHANGES
Emergency hazard warning flasher control
Previous Current
Operating condition
If the emergency braking signal is received, the
hazard warning flasher blinks 4 times/second for
10 seconds.
Deactivation conditions:
Returns to normal operation after blinking 4
times/second
Deactivated when hazard warning flasher
switch is pressed once during operation by
emergency braking signal 1.
2.Operating condition
If the emergency braking signal is received, the
hazard warning flasher blinks 4 times/second for
10 seconds.
Operation priority
Hazard warning flasher switch → Emergency
braking signal → Emergency hazard warning
flasher → Multi-function automatic hazard
warning flasher
Deactivation conditions:
Vehicle speed exceeds 50 km/h when
emergency braking signal is received
(activated at speed of 50km/h or less)
Vehicle speed increases more than 10 km/h
above the speed when the signal is received
during operation by emergency braking signal
Turn emergency hazard warning flasher switch
OFF during operation by emergency braking
signal
Deactivated automatically 10 seconds after if
items 2) and 3) above are not met during
operation by emergency braking signal
If multi-function automatic hazard warning
flasher signal is received during operation by
emergency braking signal, it will be overridden. 1.
2.

03-10
1) Wiper Control
(1) Wiper mist & front washer coupled wiper
Wiper mist ▶
When the multi-function switch is rotated for more than 0.1 second to activate the mist mode with
IGN1 ON, the wiper relay is activated after 0.1 second. It will be deactivated when the wiper motor
is in the parking position.
While the wiper operates at high speed when the mist switch signal is received, it operates at low
speed if the switch is returned to its starting position. 1.
2.
Front washer coupled wiper ▶
When holding the front washer switch at ON position for more than 0.6 seconds with IGN ON, the
wiper relay is activated 0.5 seconds after. The wiper stops after three more wipes since that the
washer switch is turned to "OFF" position. 1.

03-118710-01
Rear washer motor control ▶
When turning ON the rear washer switch with the key inserted and IGN ON, the washer fluid is
sprayed the side fascia panel.
If the front washer or automatic washer switch signal is received during the rear washer switch
operation, the washer motor stops and the front washer or automatic washer motor begins to operate. 1.
2.
When holding the front washer switch at ON position for 0.1 to 0.59 seconds during the wiper
operation by the intermittent/automatic wiper switch, the wiper will operate only once. When holding
the washer switch for more than 0.6 seconds, the wiper relay is activated 0.5 seconds after. The
wiper stops after three more wipes since that the washer switch is turned to "OFF" position. 3.