2012 SSANGYONG KORANDO ECO mode

15-170000-00
(2) Warm-up Control Function
Low voltage ▶
If low voltage is detected by the ECU, the idle speed increases up to 100 rpm selectively under the
driving mode until the ignition switch is turned off. Idle speed control ▶
The idle speed is controlled according to the fuel/air mixture when the engine load is changed, the
power steering wheel is turned to its end, the selector lever is in the "D" position and the A/C compresso
r
is in operation. It is also controlled according to the charge level during the purge control operation.
Ignition timing ▶
The idle speed is controlled according to the fuel/air mixture when the engine load is changed, The
<0090008e00950090009b009000960095004700880095008e0093008c0047008a0088009500470089008c00470099008c009b00880099008b008c008b0047009c00970047009b00960047005a005d020b00470096009900470088008b009d00880095008a00
8c008b0047009c00970047009b0096004700590057020b0047>to help idle speed control.
Air conditioner compressor operation ▶
The air conditioner control unit sends the air conditioner operation signal to the ECU to increase the
throttle valve opening amount in order to prevent reduction of the engine speed when the air conditioner
compressor is in operation at idling.
(3) Warm-up Control Operating Conditions
To make the catalytic converter reach a operating temperature, the ignition timing is retarded for about
20 seconds under the following conditions:
The coolant temperature is 15°C ~ 40°C when the engine is started.
The selector lever is in the "P" or "N" position. ▶
▶
Also, the idle speed increases to 1100 ~ 1500 rpm simultaneously by the idle speed control. However, as
soon as the selector lever is shifted to the D position, warming up control of the catalytic converter will be
inhibited. The information necessary to perform such control is as follows:
Coolant temperature
Engine rpm
Intake air mass
Recognizing idling status
Selector lever position ▶
▶
▶
▶
▶

03-10
1) Wiper Control
(1) Wiper mist & front washer coupled wiper
Wiper mist ▶
When the multi-function switch is rotated for more than 0.1 second to activate the mist mode with
IGN1 ON, the wiper relay is activated after 0.1 second. It will be deactivated when the wiper motor
is in the parking position.
While the wiper operates at high speed when the mist switch signal is received, it operates at low
speed if the switch is returned to its starting position. 1.
2.
Front washer coupled wiper ▶
When holding the front washer switch at ON position for more than 0.6 seconds with IGN ON, the
wiper relay is activated 0.5 seconds after. The wiper stops after three more wipes since that the
washer switch is turned to "OFF" position. 1.

03-12
Auto washer coupled wiper ▶
When turning ON the auto washer switch with IGN ON and intermittent/automatic wiper switch OFF,
the washer fluid is sprayed onto the windshield glass for 2 seconds and the wipers operate 4 times.
After then, additionally, the washer fluid is sprayed for 1.5 seconds and the wipers operate 3 times
again.
The auto washer switch signal is overridden during speed sensitive intermittent wiper, washer
coupled wiper or auto washer coupled wiper operation.
When turning the wiper switch to AUTO position during the operation of auto washer, the auto
washer stops its operation and the intermittent/automatic wiping mode will be started.
The front and rear washer switch signal are overridden during the operation of auto washer. 1.
2.
3.
4.

03-16
Washer coupled wiper in rain sensing mode ▶
When the washer switch signal is received during intermittent operation coupled with rain sensor
with IGN ON and intermittent/automatic washer switch operation, the wipers operate in washer
coupled mode regardless of the communication with the rain sensor. However, if the washer switch
signal is received the washer relay is activated and wiper relay remains activated, when the data
coupled with rain sensor indicates continuous wiper operation.
Even though the wiping system is in washer coupled wiper mode, the operating data are sent to rain
sensor. 1.
2.
Sensitivity adjustment (instant wiping) ▶
When the wiping speed control switch is turned to "FAST" with IGN2 ON, intermittent/automatic wiper
switch in "ON" position and wiper motor stop (parking position), the wiper motor operates one cycle at
low speed.
(only when the rain sensor detects raindrops)
If the wiping speed control switch is changed more than 2 stages within 2 seconds, the wiper motor
operates only one cycle. 1.
*

03-20
Wiper low/high control ▶
The wiper low relay is activated when the wiper low switch is operated and the wiper high relay
activated when the wiper high switch is operated.
The wiper motor returns to parking position and stops, even when turning off the ignition switch during
wiper operation.
The wiper relay should remain activated during wiper operation in low/high mode even though the
system does not receive P-POS signal. (During intermittent/automatic wiper operation, the wiper relay
should be deactivated after 5 seconds if there is no P-POS signal for 3 seconds in order to inform the
driver of faulty signal)
While the wiper operates at low/high speed, the front/rear washer switch can be operated but the auto
washer switch cannot.
The wiper motor returns to parking position and stops when turning off the ignition switch during wiper
operation in high mode. 1.
2.
3.
4.
5.

03-318710-01
7) Room Lamp
Door coupled room lamp and dimming control ▶
When opening any of doors while the room lamp switch in overhead console is pressed in ("Door"
coupled position), the room lamps come on. If the key is removed and door stays open, the room lamps
automatically goes off after 10 minutes. The sleep mode will be deactivated when the door is locked or
closed with the lamp OFF automatically.
When closing the door with IGN ON, the room lamps go off immediately.
When closing the door with IGN OFF, the room lamps stays on for 2 seconds and are dimmed out for
3 seconds.
When turning the ignition switch to ON position during dimming out operation, the room lamps go off
immediately.
When receiving the door unlock signal with IGN OFF, key removed and door closed, the room lamps
come on for 30 seconds. (It operates depending on REKES unlock and manual unlock signals for
BCM with SKM.)
4. When receiving the door unlock signal again in Step (4), the overhead room lamp and center room
lamp stay on for 30 seconds additionally. (For BCM with SKM, the extension depends on the REKES
unlock signal.)
When opening a door during the linked and dimming operation, the room lamps stays ON. When
closing it again, the system performs the operation in Step (1) and (2).
When all the door switches are changed from its closing state to its opening state, the room lamps are
dimmed out. The room lamps go off immediately when entering into the theft deterrent mode. (For
BCM with SKM, door lock is carried out by the REKES lock and manual lock signals.)
The room lamps come on when the auto approach function is activated. 1.
2.
3.
4.
5.
6.
7.
8.Room lamp control by door coupled room lamp operation ▶

03-32
8) Key Hole Illumination
When opening the door with IGN OFF, the key hole lamp comes on.
When closing the door, the key hole lamp stays on for 10 seconds and goes off.
When turning the ignition switch to ON position during the operation of key hole illumination, it goes of
f
immediately.
When receiving the door lock signal (entering into theft deterrent mode), the lamp goes off.
The key hole illumination function has a priority over the immobilizer function.
If the communication with the immobilizer is interrupted, the lamp comes on for 11 seconds with the
interval of 0.5s ON/0.5s OFF regardless of the operating conditions of key hole lamp.
When turning the ignition switch to ON position in "Virgin" condition, the lamp comes on for 8 seconds
with the interval of 0.5s ON/0.5s OFF. 1.
2.
3.
4.
5.
6.
(*1) ON: IGN ON
OFF: IGN OFF(*2) Open: driver or passenger door is open
Close: driver and passenger door are closed
Room lamp OFF control ▶
The room lamps stop operating when the BCM enters into the theft deterrent or sleep mode. (This is
to prevent battery discharge if the overhead room lamp and sensor room lamp switch is ON position.)
The room lamps go off automatically 10 minutes after the key is removed. After that, if the door unlock
or all door open signal is received and the key is inserted, the sleep mode is deactivated and the room
lamps operate for another 10 minutes.
The room lamps come on when the key is inserted (BCM without SKM) or the ignition switch is turned
to "ACC" or "ON" position (BCM with SKM) while the room lamps are OFF. 1.
2.
3.

03-358710-01
10) Keyless Entry
Transmitter (REKES key) ▶
When the user operates the switch of the remote control key, the vehicle control messages formatted by
its CPU are sent to the main unit wirelessly. The, the CPU control the vehicle and the main unit controls
the vehicle operation.
Door unlock/panic buttonDoor lock
Door unlock/panic button ▶
Unlocking door and tailgate (briefly press)
If you press this button, it unlocks all doors and the tailgate and deactivates the theft deterrent mode.
When the theft deterrent mode is deactivated, the emergency hazard lights blink once.
If the door, tailgate or engine hood is not opened within 30 seconds after unlocking the door with the
remote control key in theft deterrent mode, the door is locked automatically, hazard warning flasher
blinks twice and buzzer sounds once. (entering into theft deterrent mode)
Panic function (press and hold for more than 2 sec)
When pressing (over 2 sec) the button, the hazard warning flasher blinks and buzzer sounds for
about 30 seconds.
Press the UNLOCK or PANIC button to deactivate this function. 1.
-
-
-
2.
-
-