The vehicle tool kit and the lifting jack with sticker are housed in a plastic box in
the spare wheel or in the storage space for the spare wheel. There is also space
here for the removable ball rod for the trailer towing device. The box is attached
with a strap on the spare wheel.
The vehicle tool kit contains the following parts (depending on equipment fitted):
Screwdriver
Adapter for anti-theft wheel bolts
Towing eye
Clamps for removing the wheel trims
Car jack
Wheel wrench
Extraction pliers for wheel bolt caps
Replacement bulb set
Before placing the lifting jack back into its storage area, screw in the arm of the
lifting jack fully. WARNING
■ The factory-supplied lifting jack is only intended for your model of vehicle.
Under no circumstances attempt to lift heavier vehicles or other loads – risk of
injury!
■ Ensure that the vehicle tool kit is safely secured in the boot. Note
Ensure that the box is always secured with the strap. ÐChanging a wheel
ä
Introduction
This chapter contains information on the following subjects:
Preliminary work 147
Changing a wheel 147
Subsequent steps 147
Loosening and tightening wheel bolts 1481
2
3
4
5
6
7
8 Raising the vehicle 148
Securing wheels against theft 149
WARNING
■ If you are in flowing traffic, switch on the hazard warning light system and
set up the warning triangle at the prescribed distance! The national legal re-
quirements must be observed. In this way you are not only protecting yourself
but other road users as well.
■ If the wheel is damaged or in the event of a puncture, park the vehicle as far
away as possible from the flow of traffic. Park on as flat and firm a surface as
possible. ■ If the wheel has to be changed on a slope, first of all block the opposite
wheel with a stone or similar object to prevent the vehicle from unexpectedly
rolling away.
■ If the vehicle is subsequently fitted with tyres which are different to those it
was fitted with at the works, follow these guidelines » page 139, New wheels
and tyres .
■ Always raise the vehicle with the doors closed.
■ Never position any body parts, such as arms or legs under the vehicle, while
the vehicle is raised with a lifting jack. ■ Secure the base plate of the lifting jack with suitable means to prevent pos-
sible moving. A soft and slippery ground under the base plate may move the
lifting jack, causing the vehicle to fall down. It is therefore always necessary to
place the lifting jack on a solid surface or use a wide and stable base. Use a
non-slip base (e.g. a rubber foot mat) if the surface is smooth, such as cobbled
stones, tiled floor, etc. ■ Never start the engine with the vehicle sitting on the raised jack – danger of
suffering injury.
■ Only attach the lifting jack to the attachment points provided for this pur-
pose. CAUTION
■ The prescribed tightening torque of the wheel bolts for steel and light alloy
wheels is 120
Nm.
■ If the anti-theft wheel bolt is fastened too tightly, it can cause damage to the
anti-theft wheel bolt and adapter. £
146 Do-it-yourself
Loosening and tightening wheel bolts
Fig. 112
Changing a wheel: Loosening
the wheel bolts
First read and observe the introductory information and safety warn-
ings on page 146.
Loosening
›
Push the wheel wrench onto the wheel bolt up to the stop 1)
.
› Grasp the end of the wrench and turn the bolt about
one turn to the
left » Fig. 112 .
Tightening
› Push the wheel wrench onto the wheel bolt up to the stop 1)
.
› Grasp the end of the wrench and turn the bolt to the right until it is tight. WARNING
Undo the wheel bolts only a little (about one turn) as long as the vehicle has
not yet been jacked up – risk of an accident! Note
If it proves difficult to undo the bolts, carefully apply pressure to the end of the
wrench with your foodt. Keep hold of the vehicle when doing so, and make sure
you keep your footing. Ð
ä Raising the vehicle
Fig. 113
Changing a wheel: Jacking points
for positioning lifting jack Fig. 114
Attach lifting jack
First read and observe the introductory information and safety warn-
ings on page 146.
Position the lifting jack by selecting the jacking point that is closest to the faulty
wheel
» Fig. 113. The jacking point is located directly below the engraving in the
lower sill.
› Position the lifting jack below the jacking point and move it up until its claw is
positioned directly below the vertical web of the lower sill.
› Align the lifting jack so that its claw grasps the web
» Fig. 114 –
below the
embossing in the side surface of the lower sill.
› Ensure that the entire surface of the lifting jack base plate rests on level
ground and is located in a vertical position to the area » Fig. 114 where the claw
grasps the web. £
ä
1)
Use the appropriate adapter for undoing and tightening the anti-theft wheel bolts » page 149.
148 Do-it-yourself
F
Fire extinguisher 145
First-aid kit 145
Floor mats 74
Front airbag 100
Front seats 44
Fuel 124
Diesel 126
Fuel gauge 9
refer to Fuel 124
Refuelling 124
Unleaded petrol 125
Fuel consumption 110
Fuses Assignment 156
Replacing 156
G
Gear Recommended gear 11
General view Cockpit 7
Glow plug system – indicator light 21
GSM 84
H
Handbrake 72
HBA 72
Head airbag 102
Headlight cleaning system Headlight cleaning system 41
Headlights Driving abroad 113
Headlight cleaning system 41
Head restraint 46Heating 60
Defrosting windows 61
Exterior mirror 42
Rear window 39
Recirculated air mode 61
Seats 46
Heating rear window 39
HHC 72
Horn 7
I
Ignition 70
Ignition lock 70
Immobiliser 69
Information display see MAXI DOT 14
Instrument cluster 8
see Instrument cluster 8
Interior monitor 29
ISOFIX 107
J
Jacking points Raise vehicle 148
Jump-starting 152
L
Lever Main beam 36
Turn signal 36
Light Cockpit 38
Fog lights 35
Fog lights with the function CORNER 37
Hazard warning light system 37
Headlight flasher 36
Main beam 36
Parking light 34Rear fog light 35
Replacing bulbs 159
Turn signal 36
Lights Daytime running lights 35
Headlamp range adjustment 36
Low beam 34
Parking light 37
Parking light on both sides 37
Switching lights on and off 34
Warning lights 16
Loads 164
Lock Central locking system 27
Locking Emergency locking 30
Remote control 28
Locking and unlocking from the inside 27
M
MAXI DOT 14
Main menu 14
Settings 15
Maximum speed 167
MDI 90
Mirror Exterior mirror 42
Make-up 39
Manual dimming interior mirror 42
Mobile phone 84
Connecting to the hands-free system 86
Multifunction display Functions 11
Memory 12
Operation 12
Multimedia 89
172 Index
