2012 RENAULT SCENIC Engine And Peripherals EDC16CP33 Workshop Manual

13B-321V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET742
ET743
ET744
ET745
ET746
ET747
ET748
ET749
ET750
ET751
CONTINUED
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
STATUS1Request by weight of soot
Regeneration was requested based on the measurement of maximum soot weight in
the particle filter, without the particle filter warning light coming on.
STATUS2Request by estimated weight of soot
Regeneration was requested based on an estimation of maximum soot weight in the
particle filter, without the particle filter warning light coming on.
STATUS3Request by distance travelled
Regeneration has been requested after a maximum distance has been travelled
since the last successful regeneration without the particle filter warning light
coming on.
STATUS4Request by number of regeneration failures or weight of soot
This status corresponds to the appearance of DF312 Speed request.
This corresponds to the maximum number of failed regeneration or to the maximum
weight of soot in the particle filter, with the particle filter warning light coming on.
EDC16CP33
Program No.: C4
VDiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-322V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
COOL*: Cooling
ET776RECIRCULATED EXHAUST GAS COOL* SETPOINTS
STATUS
DEFINITION
ACTIVE: This status indicates that the recirculated exhaust gas cooling setpoint
is active.
INACTIVE: This status indicates that the recirculated exhaust gas cooling setpoint
is not active.
NOTESNone.
Conformity check: Engine stopped and ignition on and Engine running and engine coolant
temperature > 80°C
This status gives a setpoint for status ET587 Recirculated exhaust gas cooling. This programming changes
depending on the computer.
In the event of a fault, see the interpretation of faults DF209 EGR valve position sensor circuit and DF647 EGR
valve position regulation.
EDC16CP33_V18_ET776 / EDC16CP33_V1C_ET776 / EDC16CP33_V54_ET776 / EDC16CP33_V20_ET776 / EDC16CP33_V58_ET776 /
EDC16CP33_V5C_ET776 / EDC16CP33_V24_ET776 / EDC16CP33_V04_ET776 / EDC16CP33_V08_ET776 / EDC16CP33_V44_ET776 /
EDC16CP33_V4C_ET776 / EDC16CP33_V34_ET776 / EDC16CP33_V38_ET776 / EDC16CP33_V74_ET776 / EDC16CP33_V28_ET776 /
EDC16CP33_V62_ET776 / EDC16CP33_V26_ET776 / EDC16CP33_V60_ET776
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-323V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET781HEATER PLUGS
STATUS
DEFINITIONThis status indicates what type of heater plugs are fitted to the engine.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
STATUS1Slow plugs
STATUS2Fast plugs
STATUS3NOT DEFINED
Electrical conformity
STATUS1Slow plugs
Status ET781 is STATUS 1 if the heater plugs fitted to the engine have black rings,
otherwise run command SC036 Reinitialise programming and select HEATER
PLUGS (see Interpretation of commands).
EDC16CP33_V20_ET781 / EDC16CP33_V24_ET781 / EDC16CP33_V04_ET781 / EDC16CP33_V08_ET781 / EDC16CP33_V44_ET781 /
EDC16CP33_V4C_ET781 / EDC16CP33_V34_ET781 / EDC16CP33_V38_ET781 / EDC16CP33_V74_ET781 / EDC16CP33_V28_ET781 /
EDC16CP33_V62_ET781/ EDC16CP33_V26_ET781 / EDC16CP33_V60_ET781
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 20, 24,
26, 28, 34, 38, 44, 4C, 60,
62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-324V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET781
CONTINUED
STATUS2
Fast plugs
Status ET781 is STATUS 2 if the heater plugs fitted to the engine have white rings,
otherwise run command SC036 and select HEATER PLUGS (see Interpretation of
commands).
STATUS3NOT DEFINED
Status ET781 is STATUS 3 when the heater plugs are not configured in the injection
computer.
To determine the heater plugs fitted to the engine, visually check the colour of the
plug rings, then run command SC036 and select HEATER PLUGS
(seeInterpretation of commands).
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 20, 24,
26, 28, 34, 38, 44, 4C, 60,
62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-325V12 MR-372-J84-13B300$110.mif
13B
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
OCR*: Opening Cyclic RatioTool parameter Diagnostic tool title
PR002Alternator charge (Mégane II ph2/Scénic II ph2 only)
PR005EGR valve opening setpoint
PR006Rail pressure regulator current
PR007Rail pressure regulator current setpoint
PR008Rail reference pressure
PR009Turbocharging pressure setpoint
PR015Engine torque
PR017Fuel flow
PR022EGR valve position feedback loop difference
PR023Air flow difference
PR030Accelerator pedal position
PR035Atmospheric pressure
PR037Refrigerant pressure (Mégane II ph2/Scénic II ph2 only)
PR038Rail pressure
PR041Turbocharging pressure
PR042Filtered turbocharging pressure
PR048OCR* rail pressure regulation valve
PR051EGR valve position feedback
PR053Engine speed requested by air conditioning
PR055Engine speed
PR059Inlet air temperature
PR061Exterior air temperature
PR063Fuel temperature
PR064Coolant temperature
PR074Battery voltage
PR077EGR valve position sensor voltage
DIESEL INJECTION
Fault finding – Parameter summary table

13B-326V12 MR-372-J84-13B300$110.mif
DIESEL INJECTION
Fault finding – Parameter summary table13B
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
OCR*: Opening Cyclic Ratio
SV*: Solenoid valveTool parameter Diagnostic tool title
PR079Atmospheric pressure sensor voltage
PR080Rail pressure sensor voltage
PR082Fuel temperature sensor voltage
PR083Air temperature sensor voltage
PR084Coolant temperature sensor voltage
PR086Pedal potentiometer voltage gang 1
PR088Pedal potentiometer gang 2 voltage
PR089Vehicle speed
PR104Turbocharging SV* OCR* setpoint
PR128First EGR valve offset
PR129Last EGR valve offset
PR130Cruise control setpoint
PR132Air flow
PR157Fuel flow setpoint
PR171Air flow setpoint for EGR
PR190Engine idle speed setpoint.
PR209Turbocharging pressure loop difference
PR213Rail pressure loop difference
PR224Turbocharging pressure sensor voltage
PR225Air flow sensor voltage
PR290AC refrigerant pressure sensor voltage (Mégane II ph2/Scénic II ph2 only)
PR364Cylinder no. 1 fuel flow correction
PR365Cylinder no. 4 fuel flow correction
PR381Particle filter downstream temperature
PR382Particle filter upstream temperature
PR383Weight of soot in the particle filter

13B-327V12 MR-372-J84-13B300$110.mif
DIESEL INJECTION
Fault finding – Parameter summary table13B
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
repl*: replacement,
diff.*: differential,
OCR*: Opening Cyclic Ratio.Tool parameter Diagnostic tool title
PR385Exhaust pipe flow
PR391Mileage since particle filter repl*
PR405Cylinder no. 2 fuel flow correction
PR406Cylinder no. 3 fuel flow correction
PR412Mileage at last successful regeneration
PR414Particle filter diff* pressure
PR415Time since last regeneration
PR484Fuel regulation solenoid valve OCR*
PR490Engine air flow
PR636Turbine upstream pressure
PR667Turbine upstream temperature
PR668Turbine upstream temperature sensor voltage
PR672Damper valve position setpoint
PR739Fuel flow solenoid valve current
PR747Damper valve position
PR782Turbine upstream pressure sensor voltage
PR784DF312 recording No. 1
PR785DF312 recording No. 2
PR786DF312 recording No. 3
PR787DF312 recording No. 4
PR788DF312 recording No. 5
PR789DF312 recording No. 6
PR790DF312 recording No. 7
PR791DF312 recording No. 8

13B-328V12 MR-372-J84-13B300$110.mif
DIESEL INJECTION
Fault finding – Parameter summary table13B
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
OCR*: Opening Cyclic Ratio,
SV*: Solenoid valve,
solen*: solenoid valve.Tool parameter Diagnostic tool title
PR792DF312 recording No. 9
PR793DF312 recording No. 10
PR794Stored regeneration failure no. 1
PR795Stored regeneration failure no. 2
PR796Stored regeneration failure no. 3
PR797Stored regeneration failure no. 4
PR798Stored regeneration failure no. 5
PR799Stored regeneration failure no. 6
PR800Stored regeneration failure no. 7
PR801Stored regeneration failure no. 8
PR802Stored regeneration failure no. 9
PR803Stored regeneration failure no. 10
PR808Supplier 1-0 signal
PR816Stored regeneration start No.1
PR817Stored regeneration start No. 2
PR818Stored regeneration start No.3
PR819Stored regeneration start No.4
PR820Stored regeneration start No. 5
PR821Stored regeneration start No.6
PR822Stored regeneration start No.7
PR823Stored regeneration start No.8
PR824Stored regeneration start No.9
PR825Stored regeneration start No. 10
PR846Turbocharging SV* OCR*
PR848Regeneration failure number
PR850Fuel flow solen.* current setpoint