2012 RENAULT SCENIC Engine And Peripherals EDC16CP33 Workshop Manual

13B-273V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042CRUISE CONTROL/SPEED LIMITER
STATUS
DEFINITIONNOT DETECTED: This status indicates that the cruise control or speed limiter function
is not present on the vehicle.
INACTIVE: This status indicates that the main on/off switch of the cruise control/speed
limiter is in the rest (or neutral) position.
LIMITER: This status indicates that the driver has used the main switch to select the
speed limiter.
CRUISE CONTROL: This status indicates that the driver has used the main switch to
select the cruise control.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NOT DETECTEDThe cruise control or speed limiter function is not present on the vehicle.
INACTIVENo button has been pressed.
LIMITERThe speed limiter ON/OFF button has been pressed.
Lights the orange warning light on the instrument panel.
CRUISE
CONTROLThe cruise control ON/OFF button has been pressed.
Lights the green warning light on the instrument panel.
EDC16CP33_V18_ET042 / EDC16CP33_V1C_ET042 / EDC16CP33_V54_ET042 / EDC16CP33_V20_ET042 / EDC16CP33_V58_ET042 /
EDC16CP33_V5C_ET042 / EDC16CP33_V24_ET042 / EDC16CP33_V04_ET042 / EDC16CP33_V08_ET042 / EDC16CP33_V44_ET042 /
EDC16CP33_V4C_ET042 / EDC16CP33_V34_ET042 / EDC16CP33_V38_ET042 / EDC16CP33_V74_ET042 / EDC16CP33_V28_ET042 /
EDC16CP33_V62_ET042 / EDC16CP33_V26_ET042 / EDC16CP33_V60_ET042
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-274V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 1
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NOT DETECTEDIf the vehicle is not fitted with cruise control/speed limiter function buttons, status
ET042 Cruise control/speed limiter is permanently NOT DETECTED. Confirmation
of the absence of the cruise control or speed limiter function on the vehicle.
If the vehicle is fitted with cruise control or speed limiter function buttons and the main
switch is in the rest (or neutral) position and after the injection computer has been
programmed or reprogrammed, then status ET042 is NOT DETECTED.
To activate the cruise control or speed limiter function, press the main switch in the
cruise control position and then in the speed limiter position.
Return to rest position
The tool displays status ET042: INACTIVE.
If not, several steps must be checked:
1. Return to the multiplex network test page on the Clip application. Repeat the
multiplex network test. Re-establish dialogue with the injection computer.
CheckET042. If ET042 is INACTIVE, the injection computer has detected the
various positions of the main switch. The cruise control/speed limiter is active.
2. If ET042 is still NOT DETECTED, check that the owner of the vehicle has not
had the cruise control/speed limiter function deactivated in the past. Contact
the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-275V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 2
"INACTIVE"
When the main button is in rest position (or Neutral), status ET042 Cruise control/
speed limiter is INACTIVE.
If CRUISE CONTROL or SPEED LIMITER appears despite the main switch being in
the rest (or neutral) position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition on the switch connector on the following connections:
•AP10 of component 1081 (for Vel Satis ph 2, Laguna II ph2 and Espace IV ph2),
•AP43 of component 1081 (for Mégane II ph2),
•AP43 of component 1546 (for Scénic II ph2).
Disconnect the main switch, and when it is in the rest position, check the insulation
between the following connections:
•AP10 and 3FX of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP10 and 3PD of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP43 and 3FX of component 1081 (for Mégane II ph2),
•AP43 and 3PD of component 1081 (for Mégane II ph2),
•AP43 and 3FX of component 1546 (for Scénic II ph2),
•AP43 and 3PD of component
1546 (for Scénic II ph2).
With speed limiter selected, check the continuity between the following connections:
•AP10 and 3PD of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP43 and 3PD of component 1081 (for Mégane II ph2),
•AP43 and 3PD of component 1546 (for Scénic II ph2).
With cruise control selected, check the continuity between the following connections:
•AP10 and 3FX of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP43 and 3FX of component 1081 (for Mégane II ph2),
•AP43 and 3FX of component 1546 (for Scénic II ph2).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-276V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 3
"INACTIVE"
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Check the continuity, insulation and the absence of interference resistance of
the following connections:
•3FX and 3PD between components 1081 and 120 (for Vel Satis ph2, Laguna II
ph2, Espace IV ph2 and Mégane II ph2),
•3FX and 3PD between components 1546 and 120 (for Scénic II ph2).
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Also check:
The engine management computer connections.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-277V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 4
LIMITER
When the driver presses the main switch to the speed limiter position, status ET042
Cruise control / speed limiter becomes SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the switch was pressed in
the speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition on the switch connector on the following connections:
•AP10 of component 1081 (for Vel Satis ph2, Laguna II ph2 and Espace IV ph2),
•AP43 of component 1081 (for Mégane II ph2),
•AP43 of component 1546 (for Scénic II ph2).
Disconnect the main switch, and when it is in the rest position, check the insulation
between the following connections:
•AP10 and 3FX of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP10 and 3PD of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP43 and 3FX of component 1081 (for Mégane II ph2),
•AP43 and 3PD of component 1081 (for Mégane II ph2),
•AP43 and
3FX of component 1546 (for Scénic II ph2),
•AP43 and 3PD of component 1546 (for Scénic II ph2).
With speed limiter selected, check the continuity between the following connections:
•AP10 and 3PD of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP43 and 3PD of component 1081 (for Mégane II ph2),
•AP43 and 3PD of component 1546 (for Scénic II ph2).
With cruise control selected, check the continuity between the following connections:
•AP10 and 3FX of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP43 and 3FX of component 1081 (for Mégane II ph2),
•.AP43 and 3FX of component 1546 (for Scénic II ph2).
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-278V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 5
LIMITER
Check the continuity, insulation and the absence of interference resistance of
the following connections:
•3FX and 3PD between components 1081 and 120 (for Vel Satis ph2, Laguna II
ph2, Espace IV ph2 and Mégane II ph2)
•3FX and 3PD between components 1546 and 120 (for Scénic II ph2).
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Also check:
The engine management computer connections.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-279V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 6
CRUISE
CONTROL
When the driver presses the cruise control switch, status ET042 Cruise control/
speed limiter becomes CRUISE CONTROL.
If SPEED LIMITER or INACTIVE appears although the driver pressed the switch in
the cruise control position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition on the switch connector on the following connections:
•AP10 of component 1081 (for Vel Satis ph2, Laguna II ph2 and Espace IV ph2).
•AP43 of component 1081 (for Mégane II ph2).
•AP43 of component 1546 (for Scénic II ph2).
Disconnect the main switch, and when it is in the rest position, check the insulation
between the following connections:
•AP10 and 3FX of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP10 and 3PD of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP43 and 3FX of component 1081 (for Mégane II ph2),
• AP43 and 3PD of component 1081 (for Mégane II ph2),
•
AP43 and 3FX of component 1546 (for Scénic II ph2),
•AP43 and 3PD of component 1546 (for Scénic II ph2).
With speed limiter selected, check the continuity between the following connections:
•AP10 and 3PD of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP43 and 3PD of component 1081 (for Mégane II ph2),
•AP43 and 3PD of component 1546 (for Scénic II ph2).
With cruise control selected, check the continuity between the following connections:
•AP10 and 3FX of component 1081 (for Vel Satis ph2, Laguna II ph2 and
Espace IV ph2),
•AP43 and 3FX of component 1081 (for Mégane II ph2),
•.AP43 and 3FX of component 1546 (for Scénic II ph2).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-280V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 7
CRUISE
CONTROL
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Check the continuity, insulation and the absence of interference resistance of
the following connections:
•3FX and 3PD between components 1081 and 120 (for Vel Satis ph2, Laguna II
ph2, Espace IV ph2 and Mégane II ph2),
•3FX and 3PD between components 1546 and 120 (for Scénic II ph2).
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Also check:
The engine management computer connections.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74