2012 RENAULT PULSE brake


> (GLW    0RGHO .$2(0B5HQDXOW @
5. Place the ignition switch in the “ON” \fosition tounlock the steering wheel.
\bhe vehicle may be moved to the desired location.
Re\flace the removed shift lock release cover after the
o\feration.
For model with Intelligent Key system: If the battery is
discharged com\fletely, the steering wheel cannot be
unlocked. Do not move the vehicle with the steering
wheel locked.
If the selector lever cannot be moved out of the “P”
(Park) \fosition, have a RENAUL\b dealer check the
CV\b system as soon as \fossible.
WARNING:
If the selector lever cannot be moved from the
“P” (Park) position while the engine is running
and the brake pedal is depressed, the stop lights
may not work. Malfunctioning stop lights could
cause an accident injuring yourself and others.
High fluid tem\ferature \frotection mode
\bhis transmission has a high fluid tem\ferature \frotec-
tion mode. If the fluid tem\ferature becomes too high
(for exam\fle, when climbing stee\f grades in high
tem\ferature with heavy loads, such as when towing a
trailer) , engine \fower and, under some conditions,
vehicle s\feed will be decreased automatically to
reduce the chance of transmission damage. Vehicle
s\feed can be controlled with the accelerator \fedal,
but engine and vehicle s\feed may be limited.
Fail-safe
When the fail-safe o\feration occurs, the CV\b will not
be shifted to the selected driving \fosition.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
place the ignition switch in the “OFF”position
and wait for 10 seconds. Then turn the ignition
switch back to the “ON”position. The vehicle
should return to its normal operating condition.
If it does not return to its normal operating
condition, have a RENAULT dealer check the
transmission and repair it if necessary.
WARNING:
When the fail-safe operation occurs, vehicle
speed may be gradually reduced. The reduced
speed may be lower than other traffic, which
could increase the chance of a collision. Be
especially careful when driving. If necessary, pull
to the side of the road at a safe place and allow
the transmission to return to normal operation,
or have it repaired if necessary.
DRIVING WI\bH MANUAL \bRANSMISSION
(M\b)
WARNING:
. Do not downshift abruptly on slippery roads.
This may cause a loss of vehicle control.
. Do not over-rev the engine when shifting to
a lower gear. This may cause a loss of
vehicle control or engine damage.
CAUTION:
.Do not rest your foot on the clutch pedal
while driving. This may damage the clutch
system.
. Fully depress the clutch pedal before shift-
ing to help prevent transmission damage.
. Stop the vehicle completely before shifting
into the “R” (Reverse) position.
. When the vehicle is stopped for a period of
time, for example waiting at stoplights, shift
to the “N” (Neutral) position and release the
clutch pedal with the foot brake pedal
depressed.
. Do not shift to the "N" (Neutral) position
while driving. Doing so may result in an
accident due to loss of engine braking.
Starting and driving5-17
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-18Starting and driving
Starting vehicle
1. After \ftarting the engine, depre\f\f the cl\btch pedalto the floor and move the \fhift lever to the “1” (1\ft)
or “R” (Rever\fe) po\fition.
2. Slowly depre\f\f the accelerator pedal, relea\fing the cl\btch pedal and parking brake at the \fame
time.
Shifting gear
SSD0084
To change gear\f, or when \bp\fhifting or down\fhifting,
f\blly depre\f\f the cl\btch pedal, \fhift into the appropriate
gear, then \flowly and \fmoothly relea\fe the cl\btch
pedal.
To en\f\bre \fmooth gear change\f, f\blly depre\f\f the
cl\btch pedal before operating the \fhift lever. If the
cl\btch pedal i\f not f\blly depre\f\fed before the
tran\fmi\f\fion i\f \fhifted, a gear noi\fe may be heard.
Tran\fmi\f\fion damage co\bld occ\br.
Start the vehicle in the “1” (1\ft) po\fition and \fhift to
the “2” (2nd) , “3” (3rd) , “4” (4th) and “5” (5th) gear in
\feq\bence according to the vehicle \fpeed.
Yo\b cannot \fhift directly from the “5” (5th) po\fition into
the “R” (Rever\fe) po\fition. Fir\ft \fhift into the “N”
(Ne\btral) po\fition, then \fhift into the “R” (Rever\fe) po\fition.
If it i\f diffic\blt to move the \fhift lever into the “R”
(Rever\fe) or “1” (1\ft) po\fition, \fhift to the “N” (Ne\btral)
po\fition, and then relea\fe the cl\btch pedal once. F\blly
depre\f\f the cl\btch pedal again and \fhift into “R” or “1”.
S\bgge\fted maxim\bm \fpeed in each gear
Down\fhift to a lower gear if the engine i\f not r\bnning
\fmoothly, or if yo\b need to accelerate.
Do not exceed the maxim\bm \f\bgge\fted \fpeed (\fhown
below) in any gear. For level road driving, \b\fe the
highe\ft gear \f\bgge\fted for that \fpeed. Alway\f ob\ferve
po\fted \fpeed limit\f, and drive according to the road
condition\f which will en\f\bre \fafe operation. Do not
over-rev the engine when \fhifting to a lower gear a\f it
may ca\b\fe engine damage or lo\f\f of vehicle control.
HR12DE engine model (for Thailand, Pakistan,
Australia and New Zealand):
km/h (MPH)
1\ft 43 (27)
2nd 79 (49)
3rd 116 (72)
4th 157 (97)
5th — (—)HR12DE engine model (for India and South
Africa):
km/h (MPH)
1\ft 47 (29)
2nd 86 (53)
3rd 126 (78)
4th 160 (99)
5th — (—)
HR12DE engine model (for Europe)/HR15DE
engine model (for China): km/h (MPH)
1\ft 51 (32)
2nd 93 (58)
3rd 137 (85)
4th 174 (108)
5th — (—)
HR15DE engine model (for Australia, New Zeal-
and and South Africa): km/h (MPH)
1\ft 44 (27)
2nd 79 (49)
3rd 117 (73)
4th 158 (98)
5th — (—)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
HR12DE engine model (for Indonesia, Brunei,
Singapore) :km/h (MPH)
1st 39 (24)
2nd 72 (4\f)
3rd 10\f (66)
4th 143 (\b9)
\fth — (—)
HR12DE engine model (for Central and South
America, and Caribbean countries): km/h (MPH)
1st 39 (24)
2nd 71 (44)
3rd 10\f (6\f)
4th 133 (\b3)
\fth — (—)
HR12DDR engine model (for Europe): km/h (MPH)
1st 47 (29)
2nd \b6 (\f3)
3rd 127 (79)
4th 171 (106)
\fth — (—)K9K engine model:
km/h (MPH)
1st 36 (22)
2nd 6\f (41)
3rd 92 (\f7)
4th 126 (7\b)
\fth — (—)The Idling Stop System activates to prevent unneces-
sary fuel consumption, exhaust emissions and noise.
.
When you stop the vehicle, the engine is turned
off automatically.
. When you start the vehicle again, the engine is
turned on automatically.
CAUTION:
When the vehicle is moved with the engine
stopped by the system on a downhill grade
(approximately 2km/h or more) , depress the
brake pedal quickly because the engine restarts
automatically. This may lead to an accident.
NOTE:
Idling Stop System will not activate under the
following conditions
.when the engine is kept idling without any driving
after the engine is turned on.
. when the engine coolant temperature is low.
. when the battery capacity is low.
. when the battery temperature is low or extremely
high.
. when the vehicle is moved.
. when a negative pressure booster decreases.
. when the engine hood is opened with the engine
running.
. when the engine is turned on with the engine hood
open.
. when the steering wheel is operated.
. when Idling Stop System indicator blinks at a low
speed.
. when the accelerator pedal is depressed.
Starting and driving\f-19
IDLING STOP SYSTEM (if equipped
for Thailand)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-20Starting and driving
.when the selector lever is in the "R" (Reverse\f
position.
. when the rear \befogger is turne\b on.
. when the air con\bitioner is turne\b on.
. when the Electric power steering warning light or
the Anti-lock Braking System (ABS\f warning light
(if equippe\b\f illuminate.
. when the brake pe\bal is not \bepresse\b.
. when stopping the vehicle on sloping roa\bs.
. when the power consumption is large.
NOTE:
It may take some time until Idling Stop System
activates under the following conditions:
. when the battery is \bischarge\b.
. when the outsi\be temperature is low.
. when the battery is replace\b or the battery
terminal is \bisconnecte\b for exten\be\b perio\bs
an\b then reconnecte\b.
NOTE:
The engine will not restart with releasing the
brake pedal while Idling Stop System is acti-
vated under the following condition:
. when the selector lever is in the "P" (Park\f
position.
NOTE:
The engine will restart without releasing the
brake pedal while Idling Stop System is acti-
vated under the following conditions:
. when the rear \befogger is turne\b on.
. when the air con\bitioner is turne\b on.
. when the accelerator pe\bal is \bepresse\b. .
when the steering wheel is operate\b.
. when the battery capacity is low.
. when the power consumption is large.
. when the brake pe\bal is release\b on sloping roa\bs
an\b the vehicle is move\b.
. when the brake pe\bal is release\b with the selector
lever in the "D" (Drive\f or "N" (Neutral\f position.
. when the selector lever is place\b in the "L" (Low\f ,
"D" (Drive\f or "R" (Reverse\f position from the "N"
or "P" position.
. When the negative pressure of the brake system is
not sufficiently applie\b by \bepressing the brake
pe\bal several times.
Use this system while waiting at stoplight, etc. When
the vehicle is stoppe\b for long perio\bs of time, turn off
the engine.
When the engine hoo\b is opene\b with I\bling Stop
System on, the engine will be in the normal stoppe\b
state with the buzzer soun\bing. In this case, restart the
engine with the ignition switch.
When the \briver’s \boor is opene\b with I\bling Stop
System on, I\bling Stop System continues to be
activate\b although the buzzer soun\bs an\b the I\bling
Stop System in\bicator light blinks.
OPERATING IDLING STOP SYSTEM
NOTE:
. The engine stops automatically when the
brake pedal is depressed with the selector
lever in the "D" (Drive) position.
. When the brake pedal is released, the
engine restarts automatically.
. When the Idling Stop System is activated,
the Idling Stop System indicator light illu-
minates in the meter. .
The buzzer sounds and the indicator light
appears in the meter, indicating the condi-
tion of the Idling Stop System. For more
details, see “Stop/Start System indicator
light (if equipped for Europe)/Idling Stop
System indicator light (if equipped for Thai-
land)” (P.2-18) or “Idling Stop System remin-
der buzzer (if equipped for Thailand)” (P.2-
19) .
. The accumulated time of Idling Stop System
and the current saved fuel consumption by
Idling Stop System can be checked using the
drive computer, see “Accumulated time and
current saved fuel consumption (ml (mili-
liter)) by Idling Stop System (if equipped for
Thailand)” (P.2-27) .
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
The Stop/Start System is designed to prevent
unne\fessary fuel \fonsumption, e\bhaust emissions,
and noise during a journey:
.When the vehi\fle \fomes to rest the engine is
automati\fally stopped.
. The engine is then automati\fally restarted before
you are ready to drive away.
CAUTION:
At the end of the journey the engine must be
stopped and ignition switch be turned off. Lock
the vehicle as normal. Turning the ignition OFF
will shut down all electrical systems. Failure to
do this may result in a flat battery.
NORMAL OPERATION
The Stop/Start System stops the engine and will
automati\fally restart the engine. The Stop/Start
indi\fator light is shown in the meter.
The Stop/Start System will automati\fally stop
the engine when all the following \fonditions
are valid.
For MT model
.The shift lever is in Neutral position.
. The \flut\fh pedal is fully released.
. The vehi\fle speed is below about 2 km/h (1
MPH) .
. The driver’s seat belt is fastened.
. The Intelligent Key is in the vehi\fle.
. The driver’s door is \flosed.
For CVT model
. The sele\ftor lever is in the "D" (Drive) or "N"
(Neutral) position. .
The brake pedal is depressed.
. The vehi\fle is stopped.
. The driver’s seat belt is fastened.
. The driver’s door is \flosed.
NOTE:
The following conditions must also be satisfied
before the engine is automatically stopped. If
the engine does not stop this does not indicate a
malfunction in the system:
. The engine coolant temperature is at normal
operating levels.
. The vehicle has driven some distance since
engine start.
. The battery voltage and temperature are
within normal levels.
. The hood is closed.
. The steering wheel is not being turned.
. The system is not in front defogger mode.
(automatic air conditioner)
. The mode dial is not in front defogger mode.
(manual air conditioner)
. The rear window defogger is not operated.
NOTE:
The engine will not restart if the brake pedal is
released while the Stop/Start System is acti-
vated under the following condition:
. The selector lever is in the "P" (Park) position
(for CVT model) .
When the Stop/Start System indi\fator light is
displayed the engine starts running automa-
ti\fally under at least one of the following
\fonditions.
.The \flut\fh pedal is depressed (for MT model) .
. The brake pedal is released with the sele\ftor lever
in the "D"(Drive) or "N"(Neutral) position (for CVT
model) .
. The sele\ftor lever is pla\fed in the "L"(Low) ,
"D"(Drive) or "R"(Reverse) position from the "N"
or "P" position (for CVT model) .
. The driver’s seat belt is unfastened, or the driver’s
door is open (for CVT model) .
. The brake pedal is repeatedly pressed (to maintain
vehi\fle braking performan\fe) .
. The brake pedal is strongly depressed and then
released with the sele\ftor lever in the "P" (Park)
position, resulting in de\freased va\fuum pressure
of the brake booster (for CVT model) .
. The battery voltage be\fomes low (due to ele\ftri\fal
load from other vehi\fle systems like headlights,
heaters, et\f., or au\biliary devi\fes \fonne\fted to the
12 volt so\fket inside the vehi\fle) .
. The vehi\fle speed is above about 2 km/h (1
MPH) .
. The system is in front defogger mode. (automati\f
air \fonditioner)
. The mode dial is in front defogger mode. (manual
air \fonditioner)
. The rear window defogger is operated.
NOTE:
The following conditions will prevent the Stop/
Start System from automatically restarting the
engine. Starting the engine by the ignition
switch is then necessary:
Starting and driving5-21
STOP/START SYSTEM (if equipped
for Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-24Starting and driving
WARNING:
.The VDC system is designed to help improve
driving stability but does not prevent acci-
dents due to abrupt steering operation at
high speeds or due to careless or dangerous
driving techniques. Reduce vehicle speed
and be especially careful when driving and
cornering on slippery surfaces and always
drive carefully.
. Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars, bushings and
wheels are not RENAULT-approved or are
extremely deteriorated, the VDC system may
not operate properly. This could adversely
affect vehicle handling performance, and the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If brake related parts such as brake pads,
rotors and calipers are not standard equip-
ment or are extremely deteriorated, the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If engine related parts such as a muffler are
not standard equipment or are extremely
deteriorated, the “VDC OFF” indicator or
“ SLIP ”indicator or both indicator lights
may illuminate.
. When driving on extremely inclined surfaces
such as higher banked corners, the VDC
system may not operate properly and the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate. Do not
drive on these types of roads. .
When driving on unstable surfaces such as a
turntable, ferry, elevator or ramp, the “VDC
OFF” indicator or “SLIP”indicator or both
indicator lights may illuminate. This is not a
malfunction. Restart the engine after driving
onto a stable surface.
. If wheels or tires other than those recom-
mended are used, the VDC system may not
operate properly and “VDC OFF”indicator or
“SLIP” indicator or both indicator lights may
illuminate.
. The VDC system is not a substitute for winter
tires or tire chains on a snowcovered road.
When accelerating or \friving on slipper\b surfaces, the
tires ma\b spin or sli\fe. With the Vehicle D\bnamic
Control (VDC) s\bstem, sensors \fetect these move-
ments an\f control the braking an\f engine output to
help improve vehicle stabilit\b.
. When the VDC s\bstem is operating, the “SLIP”
in\ficator in the instrument panel blinks.
. If the “SLIP” in\ficator blinks, the roa\f con\fitions
are slipper\b. Be sure to a\fjust \bour spee\f an\f
\friving to these con\fitions. Be sure to \frive
carefull\b. (See “Slip in\ficator light” (P.2-17)
an\f“Vehicle D\bnamic Control (VDC) off in\ficator
light” (P.2-18) .)
. In\ficator light
If a malfunction occurs in the s\bstem, the “SLIP”
an\f “VDC OFF” in\ficator lights illuminate in the
instrument panel. As long as these in\ficators are
illuminate\f, the VDC s\bstem function is cancele\f.
The VDC s\bstem uses a Brake Limite\f Slip Differential
(BLSD) function to improve vehicle traction. The BLSD
s\bstem works when one of the \friving wheels is
spinning on a slipper\b surface. The BLSD s\bstem
brakes the spinning wheel, which \fistributes the \friving power to the other \frive wheel. If the vehicle
is operate\f with the VDC OFF switch pushe\f an\f the
VDC s\bstem turne\f off, all VDC s\bstems will be turne\f
off. The BLSD s\bstem will still operate with the VDC
s\bstem off. If the BLSD s\bstem is activate\f, the “SLIP”
in\ficator light will blink an\f \bou ma\b hear a clunk noise
an\f/or feel a pulsation in the foot brake pe\fal. This is
normal an\f is not an in\fication of a malfunction. While
the VDC s\bstem is operating, \bou ma\b feel a pulsation
in the foot brake pe\fal an\f hear a noise or feel a
vibration from un\fer the hoo\f. This is normal an\f
in\ficates that the VDC s\bstem is working properl\b.
The VDC s\bstem computer has a built-in \fiagnostic
feature that tests the s\bstem each time \bou start the
engine an\f move the vehicle at a low spee\f forwar\f or
backwar\f. When the self-test occurs, \bou ma\b hear a
“clunk” noise an\f/or feel a pulsation in the foot brake
pe\fal. This is normal an\f is not an in\fication of a
malfunction.
VEHICLE DYNAMIC CONTROL (VDC) OFF
SWITCH
SIC1881
The vehicle shoul\f be \friven with the Vehicle D\bnamic
Control (VDC) s\bstem ON for most \friving con\fitions.
When the vehicle is stuck in mu\f or snow, the VDC
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM (if equipped except for
Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
system reduces the engine output to reduce wheel
spin. The engine speed will \fe reduced even if the
accelerator is depressed to the floor. \bf maximum
engine power is needed to free a stuck vehicle, turn
the VDC system off.
To turn off the Vehicle Dynamic Control (VDC) system,
push the VDC OFF switch. The
indicator light will
illuminate on.
Push the VDC OFF switch again or restart the engine
to turn ON the system.
WARNING:
. The Electronic Stability Program (ESP) sys-
tem is designed to help improve driving
stability but does not prevent accidents due
to abrupt steering operation at high speeds
or due to careless or dangerous driving
techniques. Reduce vehicle speed and be
especially careful when driving and corner-
ing on slippery surfaces and always drive
carefully.
. If engine related parts such as a muffler are
not standard equipment or the “ESP OFF”
indicator or “SLIP”indicator or both indica-
tor lights may illuminate.
. Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars and bushings
are not RENAULT approved or are extremely
deteriorated the ESP system may not oper-
ate properly. This could adversely affect
vehicle handling performance, and the
“ESP OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If brake related parts such as brake pads,
rotors and calipers are not standard equip-
ment or are extremely deteriorated, the “ESP
OFF” indicator or “SLIP”indicator or both
indicator lights may illuminate.
. When driving on extremely inclined surfaces
such as higher banked corners, the ESP
system may not operate properly and the
“ESP OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate. Do not
drive on these types of roads. .
When driving on unstable surfaces such as a
turntable, ferry, elevator or ramp, the “ESP
OFF” indicator or “SLIP”indicator or both
indicator lights may illuminate. This is not a
malfunction. Restart the engine after driving
onto a stable surface.
. If wheels or tires other than those recom-
mended are used, the ESP system may not
operate properly and “SLIP”indicator light
may illuminate.
. The ESP system is not a substitute for winter
tires or tire chains on a snow-covered road.
. When the ESP system is operating, the “SL\bP”
indicator
in the instrument panel \flinks.
. \bf the “SL\bP” indicator \flinks, the road conditions
are slippery. Be sure to adjust your speed and
driving to these conditions. Be sure to drive
carefully. (See “Slip indicator light” (P.2-17) and
“Electronic Sta\fility Program (ESP) off indicator
light” (P.2-16) .)
. \bndicator light
\bf a malfunction occurs in the system, the “SL\bP”
indicator lights illuminate in the instrument
panel. As long as these indicators are illuminated,
the ESP system function is canceled.
The ESP system uses a Brake Limited Slip Differential
(BLSD) function to improve vehicle traction. The BLSD
system works when one of the driving wheels is
spinning on a slippery surface. The BLSD system
\frakes the spinning wheel, which distri\futes the
driving power to the other drive wheel. \bf the vehicle
is operated with the ESP system turned off, all ESP
system functions will \fe turned off.
The BLSD system and ABS will still operate with the
ESP system off. \bf the BLSD system is activated, the
“SL\bP” indicator light will \flink and you may hear a
Starting and driving5-25
ELECTRONIC STABILITY PROGRAM
(ESP) SYSTEM (if equipped for
Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-26Starting and driving
clunk noise and/or feel a pulsa\fion in \fhe brake pedal.
\bhis is normal and is no\f an indica\fion of a malfunc\fion.
While \fhe ESP sys\fem is opera\fing, you may feel a
pulsa\fion in \fhe brake pedal and hear a noise or feel a
vibra\fion from under \fhe hood. \bhis is normal and
indica\fes \fha\f \fhe ESP sys\fem is working properly.
\bhe ESP sys\fem compu\fer has a buil\f-in diagnos\fic
fea\fure \fha\f \fes\fs \fhe sys\fem each \fime you s\far\f \fhe
engine and move \fhe vehicle a\f a low speed forward or
backward. When \fhe self-\fes\f occurs, you may hear a
“clunk” noise and/or feel a pulsa\fion in \fhe foo\f brake
pedal. \bhis is normal and is no\f an indica\fion of a
malfunc\fion.
ELEC\bRONIC S\bABILI\bY PROGRAM (ESP)
OFF SWI\bCH
JVS0022X
\bhe vehicle should be driven wi\fh \fhe Elec\fronic
S\fabili\fy Program (ESP) sys\fem on for mos\f driving
condi\fions.
When \fhe vehicle is s\fuck in mud or snow, \fhe ESP
sys\fem reduces \fhe engine ou\fpu\f \fo reduce wheel
spin. \bhe engine speed will be reduced even if \fhe
accelera\for is depressed \fo \fhe floor. If maximum
engine power is needed \fo free a s\fuck vehicle, \furn
\fhe ESP sys\fem off.\bo \furn off \fhe ESP sys\fem, push \fhe ESP OFF swi\fch
loca\fed on \fhe lower side of \fhe ins\frumen\f panel.
\bhe
indica\for ligh\f will illumina\fe.
Push \fhe ESP OFF swi\fch again or res\far\f \fhe engine
\fo \furn on \fhe sys\fem. \bhe speed limi\fer allows you \fo se\f \fhe desired vehicle
speed limi\f. While \fhe speed limi\fer is ac\fiva\fed, \fhe
driver can perform normal braking and accelera\fion,
bu\f \fhe vehicle will no\f exceed \fhe se\f speed.
WARNING:
.
Always observe posted speed limits. Do not
set the speed over them.
. Always confirm the setting status of the
speed limiter on the vehicle information
display and instrument panel.
When \fhe speed limi\fer is on, \fhe cruise con\frol canno\f
be opera\fed.
SPEED LIMI\bER OPERA\bIONS
Excep\f for HR12DDR engine model: \bhe speed limi\fer
can be se\f be\fween 30 km/h and 170 km/h or 20 MPH
and 105 MPH.
For HR12DDR engine model (for M\b model): \bhe
speed limi\fer can be se\f be\fween 30 km/h and 180
km/h or 20 MPH and 112 MPH.
For HR12DDR engine model (for CV\b model): \bhe
speed limi\fer can be se\f be\fween 30 km/h and 170
km/h or 20 MPH and 105 MPH.
\bhe speed limi\fer se\f swi\fches are loca\fed on \fhe
s\feering wheel.
SPEED LIMITER (if equipped for
Europe)
&RQGLWLRQ