2012 RENAULT KANGOO ZERO EMISSION charging

heating system ..................................... (up to the end of the DU)
heating, air conditioning: programming (up to the end of the DU)
ventilation ............................................. (up to the end of the DU)
3.7
ENG_UD23009_2
Chauffage, climatisation : préchambrage (X61 électrique - Renault)
ENG_NU_911-4_F61e_Renault_3
programming
Air ConditioninG/HeA tinG: programming (1/2)
Adjusting the programming
This function enables the electric net -
work (and the not the traction battery)
to be used under certain conditions, in
order to obtain a comfortable tempera-
ture prior to using the vehicle.
It triggers the heating in cold weather
and the fan in warm weather.
1
operating conditions
– the ignition must be switched off;
– the battery charging must be finished
for the function to be triggered;
– the vehicle has to be plugged into
the mains;
and
– control 1 must be position
ṗ.
2
In cold weather (< 0°C), you are rec-
ommended to position control 2 in
air recirculation position. This ena -
bles greater efficiency and lower
energy consumption in the passen-
ger compartment ambient tempera-
ture.

3.8
ENG_UD23009_2
Chauffage, climatisation : préchambrage (X61 électrique - Renault)
ENG_NU_911-4_F61e_Renault_3
Air ConditioninG/HeA tinG: programming (2/2)
Activating the function
– With the ignition on, control 1 on
ṗ;
– switch off the ignition;
– charge your vehicle;
The function triggers on the hour pre -
ceding the hour programmed in order to
reach a comfortable temperature.
Automatically switching off the
function
– about 30 minutes after the pro -
grammed time;
– if the charging socket is discon -
nected;
– if control 1 is not in position
ṗ.
2
3
A
B
Programming the function start time
– To programme the start time, hold
button B down on stalk 3 until the
message “Settings menu” appears
on the display 2;
– scroll through the menu using but -
tons A and B until you see the
ṗ
symbol;
– hold down button B on stalk 3 - the
hours flash; –
press button A to adjust them;
– hold down button B on stalk 3 - the
minutes flash;
– press button A to adjust them;
– confirm by pressing button B on
stalk 3.
The
ṗ symbol and the programmed
time are displayed on the instrument
panel.

bonnet................................................... (up to the end of the DU)
maintenance: mechanical ...................................... (up to the end of the DU)
4.2
ENG_UD20963_2
Capot moteur (X61 - F61 - Renault)
ENG_NU_911-4_F61e_Renault_4
Jaune NoirNoir texte
Bonnet
Opening
Pull control 1 towards you.
Lift the bonnet by several centimetres
and push lever 2 to the left.
Lift the bonnet up and release stay 4
from its holder 5. For your own safety,
it is very important to fit the stay into
its retainer 3. Check that it is correctly
locked.
BOnnet (1/2)
The engine may be hot
when carrying out opera -
tions in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
1
2
In the event of an impact,
even slight, against the ra -
diator grille or bonnet, have
the bonnet catch checked
by an approved dealer as soon as
possible.
After carrying out any work
in the engine compart -
ment, check that nothing
has been left behind (cloth,
tools, etc.).
Otherwise, this may lead to engine
damage.
Do not do any work under
the bonnet when the vehicle
is charging or when the igni -
tion is switched on.

coolant ................................................................... (current page)
levels: coolant ............................................................. (current page)
tanks and reservoirs coolant ............................................................. (current page)
4.4
ENG_UD26206_3
Niveaux (X61 électrique - Renault)
ENG_NU_911-4_F61e_Renault_4
Jaune NoirNoir texte
Replacement intervals
Refer to the Maintenance Document for
your vehicle.
Levels
coolant
LeveLs (1/2)
CoolantThe level is checked with the engine
switched off and on flat ground. The
level when cold must be between the
“MIN” and “MAX” marks on coolant res-
ervoir 1 and 2 measures.
Top this level up when cold before the
“MINIMUM” mark is reached. Checking intervals
Check the coolant level regularly
(very severe damage is likely to be
caused to the engine if it runs out of
coolant).
If the level needs to be topped up, only
use products approved by our Technical
Department which ensure:
–
protection against freezing;
– anticorrosion protection of the cool -
ing system.
No operations should be
carried out on the cooling
circuit when the engine is
hot.
Risk of burns.
Consult your approved dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
12
The engine may be hot
when carrying out opera -
tions in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
Do not do any work under
the bonnet when the vehicle
is charging or when the igni -
tion is switched on.

12 volt battery ....................................... (up to the end of the DU)
12 volt battery maintenance ................................... (up to the end of the DU)
4.6
ENG_UD25386_3
Batterie (X61 électrique - Renault)
ENG_NU_911-4_F61e_Renault_4
Jaune NoirNoir texte
12 volt battery
Maintenance
Refer to the Maintenance Document for
your vehicle.
Handle the battery with care
as it contains sulphuric acid,
which must not come into
contact with eyes or skin. If
it does, wash the affected area with
plenty of cold water. If necessary,
consult a doctor.
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
12 vOL t BatteR y (1/2)
never open the battery cover 1.
The charge status of the 12V battery
can decrease, especially if you use
your vehicle:
– when the exterior temperature drops;
– after extended use of energy-con -
suming devices (radio etc.) with the
engine switched off.
Replacement
As this operation is complex, we advise
you to contact an approved Dealer.
1
The battery is a specific
type , please ensure it is
replaced with the same
type. Consult an approved
dealer.
Do not work on the 12 volt
battery (charging, replac -
ing, etc.):
– without switching off the
ignition;
– if your traction battery is charg -
ing.
Please refer to the information
on “Electric vehicle: charging” in
Section 1.
Risk of serious injury.
Replacing the 12V battery
For your own safety, you
must respect the replace -
m e n t i n te r v a l s ( w i th o u t
exceeding them) as stated in the
maintenance document.

JauneNoirNoir texte
4.7
ENG_UD25386_3
Batterie (X61 électrique - Renault)
ENG_NU_911-4_F61e_Renault_4
a234
567
Label A
Observe the indications on the battery:
– 2 naked flames and smoking are for-
bidden;
– 3 eye protection required;
– 4 keep away from children;
– 5 explosive materials;
– 6 refer to the handbook;
– 7 corrosive materials.
The engine may be hot
during operations in close
proximity. In addition, the
engine cooling fan may
start at any moment.
Risk of injury.
12 vOL t BatteR y (2/2)
Do not do any work under
the bonnet when the vehicle
is charging or when the igni -
tion is switched on.

4.10
ENG_UD26559_3
Entretien de la carosserie (X61 - X38 - X61 électrique - L38 électrique - X10 - Renault)
ENG_NU_911-4_F61e_Renault_4
using a roller type car wash
Return the windscreen wiper stalk to
the Park position (refer to the informa-
tion on the “Windscreen washer, wiper”
in Section 1). Check the mounting of
external accessories, additional lights
and mirrors, and ensure that the wiper
blades are secured with adhesive tape.
Remove the radio aerial mast if your
vehicle is fitted with this equipment.
Remember to remove the tape and refit
the antenna after washing.
Observe the vehicle stopping distances
when driving on gravelled surfaces to
prevent paint damage.
Repair, or have repaired quickly, areas
where the paint has been damaged, to
prevent corrosion spreading.
Remember to visit the body shop pe
-
riodically in order to maintain your
anti-corrosion warranty. Refer to the
Maintenance Document.
Respect local regulations about wash -
ing vehicles (e.g. do not wash your ve-
hicle on a public highway).
If it is necessary to clean mechani -
cal components, hinges, etc., spray
them with products approved by our
Technical Department to protect them
after they have been cleaned.
BODyWORk MaIntenanCe (2/2)
Cleaning the headlights
As the headlights are made of plastic
“glass”, use a soft cloth or cotton wool
to clean them. If this does not clean
them properly, moisten the cloth with
soapy water, then wipe clean with a soft
damp cloth or cotton wool.
Finally, carefully dry off with a soft dry
cloth.
Cleaning products containing alco -
hol must not be used.
vehicles with a matte paint
finish
This type of paint requires certain pre-
cautions.
Do not do the following
– use wax-based products (polishing);
– rub too hard;
– wash the vehicle in a roller-type car
wash;
– wash the vehicle using a high-pres-
sure device;
– attach stickers to the paintwork (risk
of leaving marks).
y ou should do the following
Wash the vehicle by hand using plenty
of water, using a soft cloth or a gentle
sponge.
We have selected special products
to care for your vehicle and you can
obtain these from the manufactur -
er’s accessory outlets.
Washing the vehicle
Never wash the engine
compartment, the charging
connection or the traction
battery with a high-pressure jet.
This risks damaging the electric cir-
cuit.
Never wash the vehicle while it is
charging.
Risk of electric shock and a risk to
life.

bulbschanging ......................................... (up to the end of the DU)
changing a bulb .................................... (up to the end of the DU)
front lights changing bulbs ................................ (up to the end of the DU)
bulbs changing ......................................... (up to the end of the DU)
lights: dipped beam headlights ................................... (current page)
lights changing bulbs ................................ (up to the end of the DU)
lights front ................................................. (up to the end of the DU)
5.15
ENG_UD25296_2
Projecteurs : remplacement des lampes (X61 - F61 - Renault)
ENG_NU_911-4_F61e_Renault_5
Headlights: changing bulbs
The bulbs are under pres -
sure and can break when
replaced.
Risk of injury.
Dipped beam/main beam
headlights
Turn cover 1 a quarter of a turn to
unlock it.
Disconnect the wiring.
Remove rubber protector 2.
Unclip spring 3 to remove the bulb.
heaDlIghts : changing bulbs (1/2)
1
2
3
Bulb type: h4
It is essential to use 55W anti UV bulbs
to prevent damage to the lights' plastic
glass.
Do not touch the bulb glass. hold it
by its base.
To refit it, carry out the above opera -
tions in reverse order.
Ensure that rubber protector 2 is re -
positioned correctly so that the three
strips can be seen.
To comply with local legislation, or
as a precaution, you can obtain an
emergency kit containing a set of
spare bulbs and fuses from an ap -
proved Dealer.
The engine may be hot
during operations in close
proximity. In addition, the
engine cooling fan may
start at any moment.
Risk of injury.
Do not do any work under
the bonnet when the vehicle
is charging or when the igni -
tion is switched on.