2012 RENAULT FLUENCE ZERO EMISSION lock

1.20
ENG_UD20063_2
Verrouillage / Déverrouillage des portes (L38 - X38 - Renault)
ENG_NU_914-4_L38e_Renault_1
lOcKiNg/UNlOcKiNg the DOOrS (2/2)
interior locking/unlocking
door control
Switch 3 simultaneously controls the
doors and the boot.
If a door or the tailgate is open or not
closed properly, the doors and tailgate
lock/unlock quickly.
If you need to transport objects with the
boot open, the other opening elements
can still be locked: with the engine
stopped, press switch 3 for more than
five seconds to lock the other opening
elements.
locking the opening
elements without the radio
frequency remote control
For example, in the event of a dis -
charged battery or the radio frequency
remote control temporarily not working.
With the engine switched off and
an opening element (door or boot)
open, press and hold switch 3 for more
than five seconds.
When the door is closed, all the doors
and the tailgate will be locked.
The vehicle can only be locked from
the outside using the radio frequency
remote control.
Door and tailgate status
indicator
With the ignition on, the indicator light
integrated in the switch 3 informs you
of the status of the opening elements:
– when the light is on, the opening ele-
ments are locked;
– indicator light off, the doors and tail-
gate are unlocked.
When you lock the doors, the indicator
light remains lit and then goes out.3
Driver’s responsibility
Never leave your vehicle
with the key or remote con-
trol inside.
If you decide to keep the doors
locked when you are driving, re -
member that it may be more diffi -
cult for those assisting you to gain
access to the passenger compart -
ment in the event of an emergency.

RENAULT ANTI-INTRUDER DEVICE (RAID) (up to the end of the DU)
central door locking .............................. (up to the end of the DU)
doors ..................................................... (up to the end of the DU)
locking the doors .................................. (up to the end of the DU)
doors/tailgate ........................................ (up to the end of the DU)
1.21
ENG_UD21529_3
Condamnation automatique des ouvrants en roulage (L38 - X38 - Renault)\
ENG_NU_914-4_L38e_Renault_1
Automatic locking of opening elements when driving
AUt OmA tic lOcKiNg WheN DriviNg
Activating/deactivating the
function
Depending on the vehicle:
– Please refer to the information on
the “Vehicle settings customisation
menu” in Section 1; “Auto door lock-
ing while driving ”:
= function activated
< function deactivated.
– With the engine running , press
button 1 for approximately 5 seconds
until you hear a beep.
Operating principle
After the vehicle is started, the system
automatically locks the doors when you
are driving at approximately 6 mph (10
km/h) and over.
The door can be unlocked:
– by pressing the door unlocking
button 1.
– by opening a front door (vehicle sta-
tionary).
NB: if a door is opened or closed, it
will automatically lock again when the
vehicle reaches a speed of 6 mph (10
km/h).
Operating faults
If you experience an operating fault
(no automatic locking, the indicator
light incorporated in button 1 does not
light up when trying to lock the open -
ing elements, etc.), firstly check that the
opening elements are properly closed.
If they are properly closed, contact an
authorised dealer.1
Driver’s responsibility
If you decide to keep the
doors locked when you are
driving, remember that it
may be more difficult for those as -
sisting you to gain access to the
passenger compartment in the
event of an emergency.

headrest................................................ (up to the end of the DU)
front seats adjustment ...................................... (up to the end of the DU)
adjusting your driving position .............. (up to the end of the DU)
1.22
ENG_UD29257_1
Appuis-tête avant (L38 électrique - Renault)
ENG_NU_914-4_L38e_Renault_1
Jaune NoirNoir texte
Headrests - Seats
FrONt heADreStS (1/2)
headrest A
to raise the headrest
Pull the headrest upwards to the de -
sired height.
t o lower the headrest
Press button 2 and guide the headrest
down to the desired height. t
o adjust the angle of the headrest
Depending on the vehicle, push back or
draw the headrest 4 nearer to you until
the desired position.
t o remove the headrest
Raise the headrest to its highest po -
sition (tilt the seatback backwards if
necessary). Press button 1 and lift the
headrest to release it.
t o refit the headrest
Pull out the headrest rods 3 as far as
possible by pulling from the top. Take
care to ensure they are clean and cor-
rectly aligned and, if there are any prob-
lems, check that the notches are facing
forwards.
Insert the headrest rods into the holes
(tilt the seatback backwards if neces -
sary).
Lower the headrest until it locks, press
button 1 and lower the headrest as far
as possible.
Check that each headrest rod 3 is se -
curely locked in the seatback by trying
to pull them up or push them down.
The headrest is important
for safety. Ensure that it is in
place and in the correct po-
sition: The top of the head -
rest should be as close as possible
to the crown of the head and the dis-
tance between your head and the
headrest should be the least pos -
sible.
2
3
A
1
The three upper positions can
be manipulated without pressing
button 2. However, it is preferable to
press this button to lower the head-
rest.
4

JauneNoirNoir texte
1.23
ENG_UD29257_1
Appuis-tête avant (L38 électrique - Renault)
ENG_NU_914-4_L38e_Renault_1
headrest B
to raise the headrest
Pull the headrest upwards to the de -
sired height.
t o lower the headrest
Press button 5 and guide the headrest
down to the desired height. t
o remove the headrest
Raise the headrest to its highest po -
sition (tilt the seatback backwards if
necessary). Press button 5 and lift the
headrest to release it.
t o refit the headrest
Pull the headrest rods fully out 6 by pull-
ing from the top. Take care to ensure
they are clean and correctly aligned
and, if there are any problems, check
that the notches are facing forwards.
Insert the headrest rods into the holes
(tilt the seatback backwards if neces -
sary).
Lower the headrest until it locks, press
button 5 and lower the headrest as far
as it will go.
Check that each headrest rod 6 is se -
curely locked in the seatback by trying
to pull them up or push them down.
FrONt heADreStS (2/2)
B
5
6
The headrest is important
for safety. Ensure that it is in
place and in the correct po-
sition: The top of the head -
rest should be as close as possible
to the crown of the head and the dis-
tance between your head and the
headrest should be the least pos -
sible.

front seat adjustment ............................(up to the end of the DU)
front seats adjustment ...................................... (up to the end of the DU)
front seats with manual controls ........................................ (current page)
1.25
ENG_UD23710_3
Sièges avant à commandes manuelles (L38 - X38 - Renault)
ENG_NU_914-4_L38e_Renault_1
FrONt SeA tS With mANUAl cONtrOl
to move the seat forwards or
back
Lift handle 1 to unlock. Release the
handle once the seat is in the correct
position and ensure that the seat is fully
locked into position.
t o raise or lower the seat
base
Move lever 2 as many times as neces-
sary upwards or downwards.
t o tilt the seatbackTurn control knob 3 to the required po-
sition.
For safety reasons, carry out any adjustments when the vehicle is not
being driven.
We would advise you not to recline the seatbacks too far to ensure that
the effectiveness of the seat belts is not reduced.
No object should be placed on the floor (in front of the driver). Nothing should be
placed around the driver’s feet as such objects may slide under the pedals during
sudden braking manoeuvres and obstruct their use.
1
3
2
4
t o adjust the lumbar support
on the driver’s seat
(depending on vehicle)
Lower handle 4 to increase the support
and lift it to decrease it.

JauneNoirNoir texte
1.27
ENG_UD25350_3
Ceintures de sécurité (L38 - X38 - Renault)
ENG_NU_914-4_L38e_Renault_1
UnfasteningPress button 4 and the seat belt will be
rewound by the inertia reel. Guide the
belt into position.
™Front seat belt reminder
warning light
It lights up on the central display when
the engine is started and, if the driv -
er’s seat belt is not fastened, the light
flashes and a beep sounds for about
two minutes when the vehicle reaches
a speed of approximately 12 mph
(20 km/h).
NB: an object placed on the passenger
seat cushion may activate the warning
light in some cases.
SeA t BeltS (2/3)
locking
Unwind the belt slowly and smoothly
and ensure that buckle 3 locks into
catch 5 (check that it is locked by pull -
ing on buckle 3). If the belt jams, allow
it to return slightly before attempting to
unwind it again.
If your seat belt is completely jammed,
pull slowly, but firmly, so that just over
3 cm unwinds. Allow it to return slightly
before attempting to unwind it again.
If there is still a problem, contact an ap-
proved dealer.
1
5
34
5
Adjusting the front seat belt
height
Press button 6 to adjust the seat belt
height so that the shoulder strap 1 is
worn as shown previously:
– to lower the seat belt, press button 6
and lower the seat belt at the same
time;
– to raise the seat belt, press button 6
and raise the seat belt at the same
time.
Make sure that the seat belt is locked
in position correctly after you have ad-
justed it.
6

seat belts .............................................. (up to the end of the DU)
additional methods of restraint ............. (up to the end of the DU)
additional methods of restraint to the front seat belts ......................(up to the end of the DU)
additional methods of restraint to the rear seat belts .......................(up to the end of the DU)
air bag ................................................... (up to the end of the DU)
air bag ................................................... (up to the end of the DU)
pretensioners ........................................ (up to the end of the DU)
seat belt pretensioners front seat belt .................................. (up to the end of the DU)
seat belt pretensioners ......................... (up to the end of the DU)
methods of restraint in addition to the seat belts
(up to the end of the DU)
1.29
ENG_UD23032_2
Dispositifs complémentaires à la ceinture avant (L38 électriqu\
e - Renault)
ENG_NU_914-4_L38e_Renault_1
Methods of restraint in addition to the child seat belts
methODS OF reStrAiNt iN ADDitiON t O the FrONt SeAt BeltS (1/4)
Depending on the vehicle, they are
composed of:
– seat belt inertia reel pretension -
ers;
– lap belt pretensioners;
– chest-level load limiters;
– front airbags for driver and front
passenger.
These systems are designed to act in-
dependently or together when the vehi-
cle is subjected to a frontal impact.
Depending on the severity of the
impact, the system can trigger:
– seat belt locking;
– the seat belt inertia reel pretensioner
(which engages to correct seat belt
slack);
– the low volume front air bag;
– the lap seat belt pretensioners to
hold the occupant in his seat;
– the large volume front air bag.
Pretensioners
The pretensioners hold the seat belt
against the body, holding the occupant
more securely against the seat, thus in-
creasing the seat belt’s efficiency.
In the event of a severe frontal impact
and if the ignition is switched on, the
system may engage the following de -
pending on the force of the impact:
– seat belt inertia reel pretensioner 1
which instantly retracts the seat belt;
– the lap pretensioner 2 on the front
seats.
– Have the entire restraint
system checked following
an accident.
– No operation whatso -
ever is permitted on any part of
the system (pretensioners, air
bags, computers, wiring) and the
system components must not
be reused on any other vehicle,
even if identical.
– To avoid incorrect triggering of
the system which may cause
injury, only qualified personnel
from an approved dealer may
work on the pretensioner and air
bag system.
– The electric trigger system may
only be tested by a specially
trained technician using special
equipment.
– When the vehicle is scrapped,
contact an approved dealer for
disposal of the pretensioner and
air bag gas generators.
12

1.32
ENG_UD23032_2
Dispositifs complémentaires à la ceinture avant (L38 électriqu\
e - Renault)
ENG_NU_914-4_L38e_Renault_1
methODS OF reStrAiNt iN ADDitiON t O the FrONt SeAt BeltS (4/4)
Warnings concerning the driver’s air bag
– Do not modify the steering wheel or the steering wheel boss.
– Do not cover the steering wheel boss under any circumstances.
– Do not attach any objects (badge, logo, clock, telephone holder, etc.) to the steering wheel boss.
– The steering wheel must not be removed (except by qualified personnel from our Network).
– When driving, do not sit too close to the steering wheel. Sit with your arms slightly bent (see the information on “Adjusting
your driving position” in Section 1). This will allow sufficient space for the air bag to deploy correctly and be fully effective.
Warnings concerning the passenger air bag
– Do not attach or glue any objects (badge, logo, clock, telephone holder, etc.) to the dashboard on or near the air bag.
– Do not place anything between the dashboard and the passenger (pet, umbrella, walking stick, parcels, etc.).
– The passenger must not put his or her feet on the dashboard or seat as there is a risk that serious injuries may occur. In
general, parts of the body should be kept away from the dashboard (knee\
s, hands, head, etc.).
– The devices in addition to the front passenger seat belt should be reactivated as soon as a child seat is removed, to ensure
the protection of the passenger in the event of an impact.
A reAr-FAciNg chilD SeA t mUSt NOt Be FitteD tO the FrONt PASSeNger SeA t UNleSS
the ADDitiONAl reStrAiNt SYStemS, i.e. the PASSeNger Air BAg, Are DeActiv AteD.
(refer to the information on “Child safety: deactivating/activating \
the front passenger air bag” in Section 1)
All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when\
the air bag inflates.