Page 157 of 336

7/
CHECKS
MANUAL GEARBOX
AUTOMATIC GEARBOX
BRAKE PADS
BRAKE DISC WEAR
The gearbox does not require any maintenance (no oil change).
Refer to the servicing and warranty booklet for the details of
the level checking interval for this component.
The gearbox does not require any maintenance (no oil change).
Refer to the servicing and warranty booklet for details of the
level checking interval for this component.
Brake wear depends on the style of driving, particularly in
the case of vehicles used in town, over short distances.
It may be necessary to have the condition of the brakes
checked, even between vehicle services.
Unless there is a leak in the circuit, a drop in the brake fl uid level
indicates that the brake pads are worn. For information on checking brake disc wear, contact a
PEUGEOT dealer or a qualifi ed workshop.
Only use products recommended by PEUGEOT or products of
equivalent quality and specifi cation.
In order to optimise the operation of units as important as the
braking system, PEUGEOT selects and offers very specifi c
products.
To avoid damaging the electrical units, the use of a high pressure
washer in the engine compartment is strictly prohibited
.
PARKING BRAKE
If excessive travel or a loss of effectiveness of this system
is noticed, the parking brake must be checked, even
between two services.
Checking this system must be done by a PEUGEOT dealer
or a qualifi ed workshop.
Page 160 of 336
158
Take care, this product is harmful (e.g. ethylene-glycol,
colophony...) if swallowed and causes irritation to the eyes.
Keep this product out of the reach of children.
REPAIR PROCEDURE
1. Sealing
)
Switch off the ignition.
)
Uncoil the white pipe G
fully.
)
Unscrew the cap from the white pipe.
)
Connect the white pipe to the valve of the tyre to be repaired.
)
Connect the compressor's electric plug to the vehicle's 12 V socket.
)
Start the vehicle and leave the engine running.
Avoid removing any foreign bodies which have penetrated into the
tyre.
)
Turn the selector A
to the "sealant" position.
)
Check that the switch B
is in position "O"
.
Page 164 of 336
162
CHECKING TYRE PRESSURES / INFLATING
ACCESSORIES
You can also use the compressor, without injecting any product, to:
- check or adjust the pressure of your tyres,
- infl ate other accessories (balls, bicycle tyres...).
)
Turn the selector A
to the "Air" position.
)
Uncoil the black pipe H
fully.
)
Connect the black pipe to the valve of the wheel or
accessory.
If necessary, fi t one of the adaptors supplied with the kit fi rst.
)
Connect the compressor's electrical connector to the vehicle's 12 V
socket.
)
Start the vehicle and let the engine run.
)
Adjust the pressure using the compressor (to infl ate: switch B
in position "I"
; to defl ate: switch B
in position "O"
and press
button C
), according to the vehicle's tyre pressure label or the
accessory's pressure label.
)
Remove the kit then stow it.
Page 174 of 336

172
DISCONNECTING / RECONNECTING THE
CABLES
To avoid discharging the battery, do not leave the vehicle lighting
on repeatedly with the ignition off (refer to the "Energy economy
mode" paragraph).
It is advisable to disconnect the battery if the vehicle is to be left
unused for more than one month.
Do not disconnect the terminals while the engine is running.
Do not charge the batteries without disconnecting the terminals
fi rst.
Before disconnecting the battery
Wait 2 minutes after switching off the ignition before disconnecting
the battery.
Retract the active spoiler then close the windows and the doors
before disconnecting the battery.
Following reconnection of the battery
Following reconnection of the battery, switch on the ignition
and wait 1 minute before starting to permit initialisation of the
electronic systems. However, if slight problems remain following
this operation, contact a PEUGEOT dealer or a qualifi ed
workshop.
Referring to the corresponding section, you must yourself
reinitialise:
- the remote control key,
- the electric windows and the automatic partial opening of the
door windows,
- the GPS satellite navigation system.
)
Raise the locking tab D
fully.
)
Position the open clip E
of the cable on the positive terminal (+) of
the battery.
)
Press vertically on the clip E
to position it correctly against the
battery.
)
Lock the clip by lowering the tab D
.
CHARGING THE BATTERY USING A BATTERY
CHARGER
)
Disconnect the battery from the vehicle.
)
Follow the instructions for use provided by the manufacturer of the charger.
)
Reconnect starting with the negative terminal (-).
)
Check that the terminals and connectors are clean. If they are
covered with sulphate (whitish or greenish deposit), remove them
and clean them.
Do not force the tab as locking will not be possible if the clip is not
positioned correctly.
Start the procedure again.
Page 192 of 336