2012 Peugeot 508 RXH wheel bolts

8
185
i !
Practical information










Changing a wheel
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
The tools are located in the boot, behind the
r
ear seats.

Access to the tools
List of tools

All of these tools are specific to your vehicle andcan vary according to the level of equipment. Donot use them for other purposes.1.Wheelbrace. For removing the wheel trim and removing
the wheel bolts.
2. Jack with integral handle.
For raising the vehicle.
3."Bolt cover" tool.
For removing the bolt protectors
(covers)on alloy wheels.4.Socket for the security bolts (located in theglove box).
For adapting the wheelbrace to the special
"security" bolts.
5.One wheel chock for immobilising the
vehicle.
6. Towing eye.
See "Towing the vehicle".



Before doing any work on your vehicle,switch off the ignition (Ready
lamp off) to avoid any risk of injury resulting fromautomatic operation of the engine.
When using lifting equipment (a jackfor example), take care to use the
jacking points provided, so as to avoid damaging the high voltage cables.

186
ii
Practical information

Wheel with trim
When refitting the wheel
, refit the trimstarting by placing its notch facing thevalve and press around its edge withthe palm of your hand.

Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level, stable and not slippery. Apply the parking brake unless it has
been programmed to automatic mode, switch off the ignition and put the gear lever in position A
, M
or Rto block the wheels.Check that the braking warning lampand the P
warning lamp in the parkingbrake control lever come on. The occupants must get out of thevehicle and wait where they are safe.Never go underneath a vehicle raisedusing a jack; use an axle stand.


List of operations
)Remove the bolt cover from each of
the bolts using the tool 3 (according to equipment).)Fit the security socket 4on the
wheelbrace 1to slacken the security bolt(if fitted). )Slacken the other bolts using the
wheelbrace 1only.

8
187
Practical information
)Place the jack 2 in contact with one of thetwo front Aor rear B
locations provided on
the underbody, whichever is closest to the
wheel to be changed.

)
Raise the vehicle until there is sufficient space between the wheel and the ground
to admit the spare (not punctured) wheel easily.) Remove the bolts and store them in a clean place.
)
Remove the wheel.
)
Extend the jack 2
until its base plate is in contact with the ground. Ensure that the centreline of the jack base plate is directly below the location Aor B
used.

188
i
Practical information
Fitting a wheel
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. Have the tightening of the bolts and thepressure of the spare wheel checked
by a PEUGEOT dealer or a qualified workshop without delay. Have the punctured wheel repairedand refitted to the vehicle as soon as possible.


List of operations
)Put the wheel in place on the hub. )Screw in the bolts fully by hand.)Pre-tighten the security bolt using the
wheelbrace 1fitted with the security socket 4 . )Pre-tighten the other bolts using the
wh
eelbrace 1only.

8
189
Practical information
)Lower the vehicle fully.)Fold the jack 2 and detach it.
)
Tighten the security bolt using the wheelbrace1fitted with the security socket 4.4)
Tighten the other bolts using the
wheelbrace 1 only.)
Refit the bolt covers on each of the bolts
(according to equipment). )
Store the tools in the box.

212
Practical information




Accessories
A wide range of accessories and genuine par ts is available from the PEUGEOT dealer network.
These accessories and par ts have been tested and approved for reliability and safety.
They are all adapted to your vehicle and benefit from PEUGEOT's recommendation and warranty.
"Comfort":
cool box, smoker's kit, 230 V socket, torch...
"Transport solutions":
booster seats and child seats, boot tray, roof box, ski carrier, towbar-mounted bicycle carrier,
towbars (swan-neck, quickly detachable ball, folding), harnesses, sliding floor, utility vehicleconversion kit, ...
The trailer towbar and its harness must befitted by a PEUGEOT dealer.


"Style":

spoiler, front and rear mud flaps, aluminium gear lever knob, alloy wheels (16 ", 17 ", 18 ", 19 "), body kit, door mirror shells, door air deflectors, ...

*
To avoid an
y risk of jamming of the pedals:
- ensure that the mat is positioned and
secured correctl
y,
- never fit one mat on top of another.


"Safety and security":

speed limiter/cruise control, anti-theft alarm,
microwave unit, window etching, wheel securitybolts, breathalyser, first aid kit, warningtriangle, high visibility vest, stolen vehicle
tracking system, winter equipment (17" wheels for snow chains), reversing camera, front andrear parking sensors, boot spacers...

"Protection":

mats *
, seat covers, vehicle covers, sun blinds,boot net, load protection net, dog guard, door
and boot sill protectors, resin side rubbing
strips...