Page 20 of 302
18
Familiarisation
Monitoring
On switching on, the dial needles go to
the extent of their travel then return to 0. A. With the ignition on, the needle shouldindicate the fuel remaining. B.With the engine running, the associated low level warning lamp should go off.
Instrument panel
1.
With the ignition on, the orange and red
warning lamps come on.2.With the engine running, these warninglamps should go off.
If a warning lamp remains on, refer to the page concerned.
Warning lamps
46
C.
With the ignition on, the instrument panelscreen should indicate the oil level.
If the levels are not correct, top up the level
whi
ch is low.
45
Page 28 of 302
26
i
Hybrid system
Stopping your vehicle and the hybrid system
- With the electronic key inside the vehicle,
then press the START/STOPbutton or turn
the key fully off to position 1 (stop) then
remove the key from the ignition switch;
the parking brake is applied automatically if configured to do so.
-
Otherwise apply the parking brake manually, the Pwarning lamp must be on. - Apply the brake until the vehicle comes to acomplete stop.
- Place the gear lever in position N.
When stationary, switch off the ignition and check that the Readylamp is off before leaving the vehicle. Otherwise the hybrid system will still be active.See the section on "Underbonnet precautions/warnings".
Page 29 of 302
.
27
!
Hybrid system
Ignition on without starting
the engine
(accessory position)
Anti-theft protection
Electronic engine immobiliser
The keys contain an electronic chip which hasa secret code. When the ignition is switched
on, this code must be recognised in order for
starting to be possible.
This electronic engine immobiliser locks
the en
gine management system a few minutesafter the ignition is switched off and prevents
starting of the engine by anyone who does not have the key.
In the event of a malfunction, you are informed by a message in the instrument panel screen.In this case, your vehicle does not start; contacta PEUGEOT dealer as soon as possible.
Turn the ke
y towards the dashboard to the
intermediate position or with the Keyless Entry
and Star ting key inside the vehicle, press the
"START/STOP" button, with no action on the pedal. This switches on the ignition and so
activates the ancillary equipment.
)Press the "START/STOP" button,
the instrument panel comes on
but the en
gine does not star t. )Press the button again to switchoff the ignition and so allow the
vehicle to be locked.
Using the ancillaries for a long periodintroduces the risk of a flat battery.
Page 38 of 302
36
Hybrid system
ECO OFF switch
being switched off and so ensures that a comfor table temperature can be maintained in
the passenger compar tment (air conditioningrunning continuously).On pressing the switch, the engine restar ts
immediately.
To return to normal o
peration, press the switchagain.
After switching off the ignition, the vehicle will return to normal operation (lamp in the switch off).
Page 43 of 302
.
41
!
!
Hybrid system
High voltage
Before doing any work on
the vehicle, switch off the
ignition ( Readylamp off). y
High voltage cables
High voltage cables are routed under the
vehicle (sills); take care not to damage them when the vehicle is used for off-road activity (such as covering rough ground).
Battery precautions
The high voltage battery must not in any
circumstances be charged from an externalsource and must only be handled by a
workshop technician.
There is the risk of serious burns, as well as electric arcs that could cause serious injury or even death.
A used Ni-MH (Nickel Metal Hydride) type
high voltage battery must be removed in an
appropriate manner by a repair workshop,so that its recycling presents no risk to the environment.
Take care to position lifting equipment(jack, hoist, ...) at the locations provided to avoid damaging the cables.
The volta
ge used for the operation of theelectric motor is in the range 150 to 270 Volts.
Be sure to take account of the warning labels
fitted to the vehicle.
Ta k e great care regarding the high voltage and high temperatures of components carrying thecurrent.
Emergency cut-off
In the event of an accident, a cut-off system
blocks the high voltage current and cuts off
the fuel pump; your vehicle can no longer bestarted.
To restar t the hybrid system, contact a
PE
UGEOT dealer.
Never touch, dismantle, remove or replace the high voltage par ts, orange cables or connectors, even in the event of an accident.
Page 45 of 302
.
43
!
Hybrid system
Underbonnet precautions/warnings
Always ensure that
the ignition is switched
off (Ready lamp off)
before opening thebonnet.
The alternator-star ter motor of your hybrid
vehicle is also supplied at high voltage. If the
vehicle ignition has not been switched off, there
is a risk of the engine restar ting at any time.
Also ensure that the ignition is switched off when refuelling to avoid the enginerestarting.
Page 46 of 302
44
i
Hybrid system
Vehicle recovery
Before doing any work, with the ignition on, press the brake pedal and put the gear lever inposition N
, then switch off the hybrid system.
The
front or rear wheels must not be on the ground, use a flat-bed lorry or trailer to recover the
vehicle.
Use the towing eyes only to pull a vehicle out or to pull it onto a flat-bed.
If necessary because access to the vehicle is difficult, it can be moveda few dozen metres at a speed notexceeding 6 mph (10 km/h).
Page 47 of 302
1
45
Instruments and controls
Instrument panel
1.
Energy consumption/generation indicator (power available as a percentage) For more information refer to the "Hybrid system" section. 2.Ready lamp.
Indicates that the vehicle is ready to drive. 3.Engine oil temperature gauge. 4. Fuel gauge.
5. Engine coolant temperature gauge.
6.Speedometer (mph or km/h).
7. Cruise control or speed limiter settings.
A.Main lighting dimmer. B.
Display of aler t log.
Recall of the service information.
C. Reset the trip distance recorder.
8. Gear lever position and gear for anelectronic gear control gearbox.
9. Display zone: hybrid flow, alert messages
or state of functions, trip computer.
10.Trip distance recorder (miles or km). 11.Automatic wipersSer vice indicator (miles or km) then,
total distance recorder.
These two functions are displayedsuccessively when switching on
the ignition.
Dials and screens
Control buttons
