Page 191 of 304
8
189
Practical information
Fitting a wheel
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. Have the tightening of the bolts and thepressure of the spare wheel checked
by a PEUGEOT dealer or a qualified workshop without delay. Have the punctured wheel repaired and refitted to the vehicle as soon as possible.
List of operations
)
Put the wheel in place on the hub. )
Screw in the bolts fully by hand. )
Pre-tighten the security bolt using the
wheelbrace 1fitted with the security socket 4.4 ) Pre-tighten the other bolts using the
wh
eelbrace 1only.
Page 192 of 304
190
Practical information
Lower the vehicle fully. )Fold the jack 2 and detach it.
)
Tighten the security bolt using the wheelbrace 1fitted with the security socket 4.4 )
Tighten the other bolts using the
wheelbrace 1 only. )
Refit the bolt covers on each of the bolts
(according to equipment). )
Store the tools in the box.
Page 196 of 304
194
Practical information
Direction indicators (halogen model)
)Turn the wheel fully inwards for easy access to the wheel arch liner. )Remove the two fixing screws for the access flap, located in the wheel arch. )Pull away the wheel arch liner.
) Turn the bulb holder a quar ter of a turn and
pull it out. ) Disconnect the bulb holder connector. )
Pull the bulb and change it.
For reassembly, carry out these operations in reverse order.
Yo u m ay also contact a PEUGEOT dealer
or a qualified workshop to have these bulbs
replaced.
Integrated direction indicator
side repeaters
You should contact a PEUGEOT dealer or aqualified workshop for the replacement of thesebulbs.
Door mirror spotlamps
You should contact a PEUGEOT dealer or aqualified workshop for the replacement of the light emitting diode - LED.
Page 209 of 304
8
207
Practical information
Recovering the vehicle on a fl at-bed
From the front Access to the tools
The towing eye is located behind the rear seats. )For access to it, fold the 2/3 par t of the rear seats.
)
On the front bumper, unclip the cover bypressing at the bottom to disengage the securing lugs. )
Screw the towing eye in fully. )
Install the towing system. )
Switch on the hazard warning lamps.
Always recover the vehicle on a flat bed lorry or trailer.Never tow the vehicle with the four wheels on the ground (or the front or rear wheels only), you risk damaging the transmission.Place the gear selector in position Nand switch off the engine (Readylamp off). )
Place the gear selector in neutral - position N .
Failure to obser ve this special condition could result in damage to cer tainbraking components and the absence of braking assistance the next time the engine is star ted.
Procedure for havin
g your vehicle recovered on a flat bed lorry or trailer.
Page 211 of 304
8
209
Practical information
Vehicle recovery
Before doing any work, with the ignition on, press the brake pedal and put the gear selector toposition N, then switch off the hybrid system.
If necessary because access to the vehicle is difficult, it can be moved a few dozen metres at a speed not exceeding 6 mph (10 km/h).
Th
e front or rear wheels must not be on theground, use a flat-bed lorry or trailer to recover
the vehicle.
Use the towing eyes only to pull a vehicle out or
to pull it onto a flat-bed.
Page 215 of 304
8
213
Practical information
Accessories
A wide range of accessories and genuine par ts is available from the PEUGEOT dealer network.
These accessories and par ts have been tested and approved for reliability and safety.
They are all adapted to your vehicle and benefit from PEUGEOT's recommendation and warranty.
"Comfort":
cool box, smoker's kit, 230 V socket, torch...
"Transport solutions":
booster seats and child seats, boot tray, roof box, ski carrier, towbar-mounted bicycle carrier,
towbars (swan-neck, quickly detachable ball,folding), harnesses, sliding floor, utility vehicle conversion kit, ...
The trailer towbar and its harness shouldpreferably be fitted by a PEUGEOT dealer.
"Style":
spoiler, front and rear mud flaps, aluminium gear lever knob, alloy wheels (16 ", 17 ", 18 ",
19 "), body kit, door mirror shells, door air
deflectors, ...
*
To avoid an
y risk of jamming of the pedals:
- ensure that the mat is positioned and
secured correctly,
- never fit one mat on top of another.
"Safety and security":
speed limiter/cruise control, anti-theft alarm,
microwave unit, window etching, wheel securitybolts, breathalyser, first aid kit, warningtriangle, high visibility vest, stolen vehicle
tracking system, winter equipment (17" wheels for snow chains), reversing camera, front and rear parking sensors, boot spacers...
"Protection":
mats *
, seat covers, vehicle covers, sun blinds,boot net, load protection net, dog guard, door
and boot sill protectors, resin side rubbing
strips...
Page 231 of 304
10
229
Technical data
Identifi cation markings
Various visible markings for the identification and tracing of your vehicle.
A.Vehicle Identification Number (VIN) under the bonnet.
This number is engraved on the bodyworknear the damper suppor t.
The tyre pressures must be checked when the tyres are cold, at least oncea month.
Low tyre pressures increase fuelconsumption.
B.Vehicle identification Number (VIN) on
the windscreen lower crossmember. This number is indicated on a self-adhesive label which is visible through the
windscreen.
C.Manufacturer's label.The VIN is indicated on a self-destroying
label affixed to the door aper ture, on the driver's side.
D.Tyre/paint label.This label is fitted to the middle pillar, on
the driver's side. It bears the
following information:
- the tyre inflation pressures with and without
load,
- the tyre sizes,
- the brands o
f tyre recommended by themanufacturer,
- the inflation pressure of the spare wheel,
- the paint colour code.
The use of snow chains is onlyauthorised on the front wheels.
The selector must be in 4WD mode.
Page 272 of 304
270
08RADIO
By alphabetical list
Pr
ess RADIOor LIST , select the station
of your choice and confi rm.
B
y automatic frequency search
Pr
ess or for the automatic searchfor a lower or higher radio frequency.
Or turn the thumb wheel at the steeringmounted controls.
B
y manual frequency search
Pr
ess or to adjust the radiofrequency step by step.
Press the button on the numericalkeypad to recall a preset station.
Or press then turn the thumb wheel at
the steering mounted controls.
SELECTING A STATION
The external environment (hill, building, tunnel, underground car park...) may interfere with the reception, including in RDS station tracking mode.This phenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a fault with the audio system.
PRESETTING A STATION
After selecting a station, press one of
the buttons on the numerical keypad for 2 seconds to preset the current station.
An audible si
gnal confi rms that the
station has been preset. The qualit
y of reception is represented by the number of active waves in this
symbol.
