2012 Peugeot 508 RXH parking brake

122
Driving
Emergency braking
In the event of a failure of the main servicebrake, a continuous pull on the control lever Awill stop the vehicle.
The dynamic stability control provides stability
during emergency braking.
If the emergency braking malfunctions, a message will be displayed.

I
f a failure of the DSC system is
signalled by the lighting of this
warning lamp, then braking stability is
not
guaranteed.
In this event, stability must be assured by the
driver by repeating alternate "pull-release" actions on the control lever A.
Emergency parking brake release
)if your vehicle has one, take out the vehicle chock B , located behind the rear seats.)On a slope, immobilise the vehicle byplacing a chock in front or behind one of
the front wheels, opposing the slope. On level ground, immobilise the vehicle byplacing a chock in front or behind one of
the front wheels.
In the event o
f fault with the electric parkingbrake or a battery failure, an emergencymechanical control can be used to manually
releasethe parking brake.) Immobilise the vehicle (or chock it if the
brake pedal has not been released), with
the hybrid system active, place the gear selector in position M or R.)
Switch of the hybrid system, but leave the
ignition on. If you are unable to immobilise
the vehicle, do not operate this control and contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
The emergency braking must only be used in exceptional circumstances.

4
123
Driving
)Fold the 2/3 par t of the rear seat for access
to the green cap.

For reasons of safety you must contact a PEUGEOT dealer as soon as possibleto have the cap replaced.
Take care not to place anything dusty or
wet close to the cap.
With an emergency release,immobilisation of the vehicle is nolonger be assured once the mechanical release has started and the mechanicaltool cannot be used to apply the parking brake again.
Do not carry out any action on lever A
, or stop / star t the system while therelease tool is engaged.
Have it checked by a PEUGEOT dealer or a qualified workshop.
To r e - e ngage the electric parking brake(after correction of the fault or batteryfailure), make a long pull on the controllever A
until the parking brake warninglamp (!) flashes in the instrument panel, then make a second long pull until this warning lamp comes on fixed (not flashing).
)
Turn the release tool clockwise
. For
reasons of safetyit is essential
to keep
turning until the stop is reached. the
parking brake is released. ) Take care to refit the release tool in its
housing. ) The operation of the parking brake isreinitialised each time the ignition isswitched off and on. If reinitialisation of theparking brake is not possible, contact aPEUGEOT dealer. )
The application time may be longer than
with normal operation.
) Pierce the cap and inser t the release tool in
the tube.

The emergency braking should only be used in exceptional circumstances.

124
Driving
Operating faults
If the electric parking brake fault warning lamp comes on together with one or more of the warning lamps presented in these tables, place the vehicle ina safe condition (on level ground, gear engaged) and contact a PEUGEOT dealer or a qualified workshop without delay.
SituationsConsequences
Displa
y of the message "Parking brake fault" and of the following
warning lamps:

- The automatic functions are deactivated.

- Hill start assist is not available.

- The electric parking brake can only be used manually.
Displa
y of the message "Parking brake fault" and of the following
warning lamps:

- Manual release of the electric parking brake is only available by pressing the accelerator pedal and releasing the control lever.

- Hill start assist is not available.

- The automatic functions and the manual application are still available.
Displa
y of the message "Parking brake fault" and of the following
warning lamps:

- The automatic functions are deactivated.

- Hill start assist is not available.

4
125
Driving
SituationsConsequences
To apply the electric parking brake: ) immobilise the vehicle and switch off the ignition. )
pull the control for at least 5 seconds or until application is complete.)
switch on the ignition and check that the electric parking brake
warning lamps come on.
The application is slower than during normal operation.
To release the electric parking brake:
)
switch on the ignition. )
push the control lever and hold it for approximately 3 seconds then
release it.
If the braking warning lamp is flashing or if the warning lamps do not come on with the ignition on, these procedures will not work. Place the
vehicle on level ground and have it checked by a PEUGEOT dealer or aqualified workshop. and possibl
y

flashing
Display of the message "Parking brake fault" and of the following warning lamps:

- Only the automatic application on switching off the engine andautomatic release on acceleration functions are available.

- The manual application/release of the electric parking brake and theemergency braking are not available.
and possibly
flashin
g

Display of the message "Battery charge fault".

- You must stop as soon as it is safe to do so. Switch off and
immobilise
your vehicle (if necessary, place the a chock under a
wheel).

- Apply the electric parking brake before switching off the engine.

4
127
Driving

Engagement of reverse gear isaccompanied by an audible signal.
If you leave the vehicle, place the gear
selector in position Nand then you must stop the hybrid system by switching off the ignition (Ready
lamp off).
If the gear selector is not in position Non starting, Nflashes in the instrumentpanel, accompanied by an audiblesignal and a message in the instrument panel screen. Foot on brakeflashes on the instrument panel, accompanied by anaudible signal and a message in the instrument panel screen, if the brakepedal is not pressed on starting.


For optimum acceleration, for example
when overtaking another vehicle, pressthe accelerator pedal firmly past the point of resistance.


Displays in the instrument panel
N Neutral
R Reverse1, 2, 3, 4, 5, 6
Gears in manual mode A This comes on when automated mode is
selected. It goes off on changing to manual mode.
)Place your foot on the brakewhen a message appears in the
instrument panel screen.

Moving off
)
Select position N . )
Press the brake pedal down fully. )
Star t the hybrid system.
N
appears in the instrument panelscreen.
)
Select a gear (position M
or A
) or reverse A(position R).R)
Release the parking brake unless it is
programmed to automatic mode. ) Ta k e your foot off the brake pedal, thenaccelerate.
Aand 1or R
appear in the instrumentpanel screen.


Automatic mode
)
After star ting the vehicle, select position Afor enter automatic mode.
A
appears in the instrument panel screen.
The
gearbox is then operating in auto-active
mode, without any action on the par t of the driver. It continuously selects the most suitablegear, depending on the:


- st
yle of driving,

- profile of the road.


When the engine is idling with thebrakes off, if position R, Aor M
is selected, the vehicle will move off
on its own without any action on theaccelerator.

4
129
Driving
You must press the brake pedal when star ting the engine.
Whatever the circumstances, you mustmanually apply the parking brake when parking, unless the parking brake is programmed in automatic mode.

When immobilising the vehicle, with the hybrid system active, you must place the gear selector in neutral N
.Before carrying out any work in the engine compar tment, check that the gear selector is in neutral N
and that the
parking brake is applied.

Stopping the vehicle
With the ignition on, theflashing of this warning lamp,
accompanied by an audible
signal and a message in the instrument panelscreen, indicates a malfunction of the gearbox.
Have it checked by a PEUGEOT dealer or a qualified workshop. Be
fore switching off the engine, you can
choose to:
- move to position N
to engage neutral,
- leave the gear engaged; in this case, it will
not be possible to move the vehicle.
In both cases,
you should apply the parking brake to immobilise the vehicle.

Operating fault

This function facilitates manoeuvring of the
vehicle at low speed (when parking, in traffic jams, …).
With the hybrid system active and the parkingbrake released, if position A
, M
or Risselected, the vehicle moves as soon as you
take your foot off the brake pedal (even without
any action on the accelerator).

Creep function (moving
without the accelerator
)

Never leave children unsuper vised in the vehicle with the hybrid system active.

For
your safety, this function will only be
activated if you press the brake pedal when engaging for ward drive or reverse.
This function is deactivated if the driver's door
is opened. To reactivate it, close the door and
then press the brake or accelerator pedal.

130
Driving





Hill start assist
System which keeps your vehicle immobilised
temporarily (approximately 2 seconds) whenstarting on a gradient, the time it takes to
move your foot from the brake pedal to the accelerator pedal.
This function is only active when:
- the vehicle is completely stationary, withyour foot on the brake pedal,
- in par ticular conditions on a slope,
- with the driver’s door closed.
The hill start assist function cannot bedeactivated.
On an ascendin
g slope, with the vehiclestationary, the vehicle is held for a brief moment when you release the brake pedal,if the gear selector is in position A or M.
On a descending slope, with the vehicle
stationary and reverse gear engaged, thevehicle is held for a brief moment when you release the brake pedal.
Do not exit the vehicle while it is beingheld in the hill star t assist phase.
If you need to exit the vehicle with the hybrid system active, apply the parkingbrake manually then ensure that theparking brake warning lamp and thewarning lamp P
on the lever (of the electric brake) are permanently on.


Operating fault


If a malfunction of the system occurs, these
warning lamps come on. Contact a PEUGEOT
dealer or a qualified workshop to have the
system checked.

8
187
Practical information

Wheel with trim
When refitting the wheel
, refit the trim starting by placing its notch facing the valve and press around its edge withthe palm of your hand.

Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level,stable and not slippery. Apply the parking brake unless it has
been programmed to automatic mode,switch off the ignition and put the gear lever in position A
, M
or Rto block the wheels.Check that the braking warning lampand the P
warning lamp in the parking brake control lever come on.The occupants must get out of the vehicle and wait where they are safe. Never go underneath a vehicle raisedusing a jack; use an axle stand.


List of operations
)
Remove the bolt cover from each of
the bolts using the tool 3 (according to equipment).)
Fit the security socket 4
on the wheelbrace 1
to slacken the security bolt (if fitted). )
Slacken the other bolts using the
wheelbrace 1only.