2012 Peugeot 508 buttons

3
89
!
Comfort

8. Air distribution adjustment
)Press the corresponding button for:
Windscreen and side windows.
Centre and side vents.
F
ootwells.
To s u i t
your requirements, you cancombine two distribution buttons or select the three distribution modes
simultaneously.
9. Air fl ow adjustment
)Press this "full fan"button
to increase the air flow.
)Press "empty fan"
button
to reduce the air flow.



10. Air intake/Air recirculation
)Press this "empty fan"air flow button until the fan symbol
disappears and "--"appears.
Switching the system off
) Press this button for recirculation of the interior air. The indicator
lamp on the button comes on.

Air recirculation enables the passenger compartment to be isolated from exterior odours and smoke. It is activated automatically
when operating the screenwash.

Avoid driving for long periods with the system off (risk of condensation and deterioration of the air quality).
Pressing the "full fan"button reactivates the system with the valuesin use at the time it was switched off. The air
flow symbol, the fan, fills progressively according to the value requested.
Thi
s action switches off all of the functions of the
air conditioning system.
Temperature related comfor t is no longer guaranteed but a slight flow of air, due to the forward movement of the vehicle, can still be felt.
)
As soon as possible, press this button
again to permit the intake of outside air and prevent the formation of condensation. The
indicator lamp in the button goes off.

3
91
i
i
i
Comfort

5. Automatic visibility programme
6. Mono-zone/Quad-zone
7. Air conditionin
g On/Off
Manual o
peration

If you wish, you can change one of settings
provided by the system. The other functions will
still be controlled automatically.
Press one of the Soft/Auto/Fast buttons toreturn to fully automatic operation.

On entering the vehicle, if the interior temperature is much colder or warmer than the comfort value, there is no
need to change the value displayed in order to obtain the comfort required.The system corrects the differencein temperature automatically and asquickly as possible.
See "Front demisting-defrosting". Press this button to appl
y the driver'scomfort setting value to the front and
rear passen
gers (mono-zone). The
indicator lamp on the button comes on.
The air conditioning is designed to
operate effectively in all seasons,
with the windows closed.
It allows you:
- in summer, to lower the tem
perature,
- in winter, above 3°C, to improve demistingperformance.
Switchin
g on) Press the "A/C"
button, the associatedgreen indicator lamp comes on.The air conditioning does not operate when
the air flow control is set to off.
Switching off) Press the "A /C "
button again, the
associated green indicator lamp goes off.
Switching off the air conditioning may result in
some discomfort
(humidity, misting).

For maximum cooling or heating of thepassenger compar tment, it is possibleto exceed the minimum value 14 or themaximum value 28.)
Turn the dial 3or 4to the left until"LO"is displayed or to the right until "HI"
is displayed.
With Stop & Start, when demisting has been activated, the STOP mode is notavailable.

92
Comfort
8. Air distribution adjustment
)Press this "full fan"
button toincrease the air flow.)Press the corresponding button for:

Windscreen and side windows.
Centre and side vents.

Footwells.
To s u i t
your requirements, you cancombine two distribution buttons or select the three distribution modes
simultaneously.
)Press "empty fan"button toreduce the air flow.
)Press this "empty fan"
air flow button until the fan symbol
disappears and "- -"appears.
Automatic air intake mode
It is activated by default with automatic comfort regulation.


9. Air fl ow adjustment
The symbol for air flow, the fan, fills
progressively according to the value requested.

Switching the system off

This action switches off all of the functions of theair conditioning system.
Temperature related comfor t is no longer
assured but a slight flow of air, due to the
for ward movement of the vehicle, can still be felt.
Avoid drivin
g for long periods with the system
o
ff (risk of condensation and deterioration of
the air quality). Pressing the "full fan"buttonreactivates the system with the values in use at
the time it was switched off.

10. Air intake/Air recirculation
Air recirculation enables the passenger compar tment to be isolated from exterior
odours and smoke. It is activated automatically
when operatin
g the screenwash. It is inactive
when the ambient temperature is below 5°C to
guard against the risk of misting in the vehicle. )As soon as possible, press this buttonagain to permit the intake of outside air and prevent the formation of condensation. The
indicator lamp in the button goes off.

4
121
i
Driving





Head-up display


System which projects various information onto
a smoked strip in the field of vision of the driver so that they do not have to take their eyes off
the road.
This system operates when the engine is
running and the settings are stored when the
ignition is switched off.
1
.Head-up display on. 2. Head-up display off (long press).3.
Brightness adjustment. 4.
Display height adjustment.
Buttons
Once the system has been activated, thefollowing information is grouped together in the
head-up display:A.The speed of your vehicle. B. Cruise control/speed limiter information.


Displays during operation
C.
Navigation information (according to
version).
For more information on the navigation system, refer to the "Audio andtelematic" section.

122
i !
Driving
)With the engine running, press button 1 toactivate the system and deploy the strip. )Press and hold button 2
to deactivate the
system and retract the strip.
The activated/deactivated state is saved and restored on restar ting the engine.
Activation/Deactivation
) With the engine running, adjust the
brightness of the information displayedusing buttons 3 :


- the "sun" to increase the brightness,

- the "moon" to decrease the brightness.





Brightness adjustment
We recommend that adjustments aremade using these buttons only whenthe vehicle is stationary. When stationary or while driving, noobjects should be placed around thestrip (or in its recess) so as to not impede deployment of the strip and itscorrect operation.


In certain extreme weather conditions (rain and/or snow, bright sunshine, ...) the head-up display may not be legibleor may suffer temporary interference. Some sunglasses may hamper readingof the information.
To clean the strip, use a clean, soft cloth (such as a spectacles cloth or microfibre cloth). Do not use a dry or abrasive cloth or detergent or solventproducts as these could scratch thestrip or damage the non-reflectivecoating.

Height adjustment
)With the engine running, adjust the display
to the desired height using buttons 4 :
- up to move the display up,
- down to move the display down.

4
125
!
Driving
) Press 1, the speed limiter mode is
activated but remains paused.
You do not have to switch the s
peed limiter
on in order to set the speed. ) Set the speed value by pressingbutton 2or 3(e.g.: 55 mph (90 km/h)).


Programming


Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed speed will not have any effect unless you press the pedal firmlypast the point of resistance.
The speed limiter is deactivated temporarily and the programmedspeed, which is still displayed, flashes.
Returning to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically cancels the
flashing of the programmed speed.


Off/Return to normal
driving
)
Press 5, the speed limiter is deactivated.

On a steep descent or in the event of sharp acceleration, the speed limiter willnot be able to prevent the vehicle from exceeding the programmed speed.
The use of mats not approved byPEUGEOT may adversely affect the normal operation of the accelerator pedal and impede the operation of thespeed limiter.
Mats approved by PEUGEOT have a third fixing in the area of the pedals to avoid any risk of inter ference with thepedals.
In the event o
f a speed limiter fault, the speed
is cleared resulting in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a qualified workshop.


Operating fault
You can then change the programmed speed using buttons 2
and 3:


- by + or - 1 mph (km/h) = shor t press,

- by + or - 5 mph (km/h) = long press,

- in steps of + or - 5 mph (km/h) = maintained press. )Switch the speed limiter on by pressing button 4 . )Suspend the speed limiter by pressing button 4: the screen confirms the suspension with "Pause".)Switch the speed limiter back on by pressing button 4
again.

4
127
!
Driving
) Press 1, the cruise control is activated but remains paused.
)
Set the programmed speed by
accelerating to the required speed,
then press button 2or 3(e.g.: 70 mph (11 0 k m / h)).

Programming

You can then change the programmed speed using buttons 2
and 3
:


- by + or - 1 mph (km/h) = shor t press,

- by + or - 5 mph (km/h) = long press,

- in steps of + or - 5 mph (km/h) = maintained press. )Pause the cruise control by pressing button 4
: the screen confirmsthe suspension with with "Pause".)Switch the cruise control back on by pressing button 4again.




Exceeding the programmed speed

Intentional or unintentional exceeding of the programmed speed results
in flashing of this speed on the display.
Return to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically cancels theflashing of the speed.
When the cruise control is switched on,be careful if you maintain the pressure on one of the programmed speedchanging buttons: this may result in avery rapid change in the speed of your vehicle. Do not use the cruise control on slippery roads or in heavy traffic.

On a steep descent, the cruise control will not be able to prevent the vehicle from exceeding the programmed speed.
To avoid any risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- never fit one mat on top of another.
In the event o
f a cruise control fault, the speed
is cleared resulting in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a qualified workshop.


Operating fault

Off/Return to normal drivin
g
)Press 5
; cruise control mode is deactivated The screen returns to
the distance recorder.

274
08
1a
1b
1c
1
2
RADIO
By alphabetical list
Pr
ess RADIOor LIST , select the station
of your choice and confi rm.
B
y automatic frequency search
Pr
ess or for the automatic searchfor a lower or higher radio frequency.
Or turn the thumb wheel at the steeringmounted controls.
B
y manual frequency search
Pr
ess or to adjust the radiofrequency step by step.
Press the button on the numericalkeypad to recall a preset station.

Or press then turn the thumb wheel at
the steering mounted controls.








SELECTING A STATION


The external environment (hill, building, tunnel, underground car park...) may interfere with the reception, including in RDS station tracking mode. This phenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a fault with the audiosystem.


PRESETTING A STATION


After selecting a station, press one of
the buttons on the numerical keypad for 2 seconds to preset the current station.
An audible si
gnal confi rms that the
station has been preset. The qualit
y of reception is represented by the number of active waves in this
symbol.