2012 PEUGEOT 4008 check engine

193
7
Practical information
necessary (see "Checking levels").


Starting using another
battery
)
Connect the red cable to the positive
terminal (+) of the flat battery A
, then to the
positive terminal (+) of the slave battery B.
) Connect one end of the green or blackcable to the negative terminal (-) of the slave battery B.)
Connect the other end of the green or black cable to the ear th point C
on your vehicle(engine mounting). )
Operate the starter, let the engine run.)
Wait until the engine returns to idle anddisconnect the cables.

)Raise the protective cover on the (+)terminal.

194
Practical information

The batteries contain harmful substancessuch as sulphuric acid and lead. Theymust be disposed of in accordancewith regulations and must not, in any circumstances, be discarded withhousehold waste.
Take used remote control batteries andvehicle batteries to a special collection point.
Do not reverse the polarity and use only a 12 V charger. Do not disconnect the terminals while the engine is running. Do not charge the batteries without disconnecting the terminals first.
Do not push the vehicle to star t the engine if it is fitted with a CVT gearbox.


It is advisable to disconnect the battery
if the vehicle is to be left unused for more than one month.
Before disconnecting thebattery
Wait 2 minutes after switching off theignition before disconnecting the battery. Close the windows and the doors before disconnecting the battery.
Following reconnection of the battery
Following reconnection of the battery, switch on the ignition and wait 1 minutebefore starting to permit initialisation of theelectronic systems. However, if problemsremain following this operation, contact a PEUGEOT dealer or a qualified workshop.

)Disconnect the battery from the vehicle, if necessary.)Follow the instructions for use provided by
the manufacturer of the charger.)Reconnect starting with the negative
terminal (-). )Check that the terminals and connectors are clean. If they are covered with sulphate (whitish or greenish deposit), remove themand clean them.
Charging the battery using
a battery charger

195
7
Practical information

Removing a front or rear
wiper blade
) Raise the corresponding wiper arm.)
Remove the wiper blade, sliding it towards
the outside.










Changing a wiper
blade

Fitting a front or rear wiper
blade
) At the front, check the size of the wiper blade as the shorter blade is fitted on the
right-hand side of the vehicle.) Put the corresponding new wiper blade in
place and fix it. )
Fold down the wiper arm carefully.


Automatic power cut-off
to accessories
After the engine has stopped, when the ignition switch is in the "ACC" position(or the vehicle in "ACC" mode)
you can still use functions such as the audio equipment, windscreen wipers, dipped beamheadlamps, cour tesy lamps, etc. for about thirty
minutes.
Cutting off
Once the thir ty minutes have expired, thepower supply to the accessories will be automatically cut off.
Restoring power
The power supply will be restored the next time
the ignition is switched on.

The period before cut-off can beextended up to about sixty minutes or deactivated, via the colour screen"Equipment" menu.

200
Practical information
Driving advice
Distribution of loads
)Distribute the load in the trailer so that theheaviest items are as close as possible to
the axle and the nose weight approaches
the maximum permitted without
excee
ding it.
Air density decreases with altitude, thus reducing engine performance. Above
1 000 metres, the maximum towing load must
be reduced b
y 10 % of the GTW and so on for every 1 000 metres of altitude.
Refer to the "Technical Data" section for details
of the weights and towing loads which apply to your vehicle.
Side wind
)Take into account the increased sensitivity
to side wind.

Cooling

To w i ng a trailer on a slope increases the
temperature of the coolant.
As the fan is electricall
y controlled, its cooling capacity is not dependent on the engine speed.)
To lower the engine speed, reduce your speed.
The maximum towing load on a long slope
depends on the gradient and the outside
tem
perature.
In all cases, pay attention to the coolant
temperature.
) If this message is displayed, stop your vehicle as soon as it is safe to do so.


Braking

To w i ng a trailer increases the braking distance.


Tyres
)Check the tyre pressures of the towingvehicle and of the trailer, obser ving the recommended pressures.



Lighting
)Check the lighting and signalling on the
trailer.
I
f the message flashes slowly, wait for the engine to cool before topping up the level, if necessary.
If the messa
ge flashes rapidly, contact a PEUGEOT dealer or a qualified workshop
without delay.

205
8
Checks











Bonnet
)Open the left-hand front door.)Pull the interior bonnet release lever A ,
located at the bottom of the door aper ture.
Do not open the bonnet in high winds. When the engine is hot, handle theexterior safety catch and the bonnetstay with care (risk of burns).
)
Unclip the stay C
from its housing on the back of the bonnet. )
Fix the stay in the notch to hold the bonnet open.


Closing
)
Take the stay out of the support notch. )
Clip the stay in its housing on the back of
the bonnet.) Lower the bonnet and release it at the endof its travel. )
Pull on the bonnet to check that it is secured correctly.


The location of the interior bonnet releaselever prevents opening of the bonnet whilethe front left door is closed.


Opening
)Push the exterior safety catch B
to the left and raise the bonnet.
This messa
ge appears in the instrument panelscreen if the bonnet is not fully closed.
The cooling fan may star t after switching off the engine; take care
with ar ticles and clothing that mightbecome caught by the fan blades.

206
Checks
fluids and the replacement of cer taincomponents.














Petrol engines
1.
Screenwash and headlamp wash fluidreservoir.2.
Coolant header tank.3.
Brake fluid reservoir.4.
Battery. 5.
Fusebox.
6.Air filter.
7. Engine oil dipstick. 8.Engine oil filler cap.
1.6 litre 115
2.0 litre 150

207
8
Checks
checking the levels of the various fluids, for
replacing cer tain components and for primingthe fuel system.














Diesel engines
1.
Screenwash and headlamp wash fluidreservoir.2.Coolant reservoir.3.Brake fluid reservoir.4.
Battery.
5. Fusebox.
6.Air filter.
7. Engine oil dipstick.8.Engine oil filler cap.9.
Priming pump * . 1.6HDi 110
1.8 HDi 150
*

According to engine.

208
Checks
When the symbol begins to flashrapidly(approximately twice per second), there is not much fuelremaining in your tank (approximately5 litres).
You must fill the tank to avoid runningout of fuel.

































Fuel tank
Capacity of the tank: approximately 60 litres.
Low fuel level
Filling
A label, affixed on the inside of the flap, reminds you of the type of fuel to be usedaccording to your engine.
More than 5 litres of fuel must be added in
order to be re
gistered by the fuel gauge.

Location of the cap

When the low fuel level is reached,
this indication appears in the
instrument panel screen. When it firstcomes on, you have approximately
10 litres o
f fuel remaining.
The symbol flashes slowly(approximately
once per second).
1. Opening the filler flap. 2.Removing the filler cap.
3.Hooking the filler cap.
To
fill the tank safely: )the engine must be switched off,)
pull the control A
located at the bottom left of the driver's seat to release the fuel filler flap, )
open the fuel filler flap B , )
turn the filler cap C
to the left, )
remove the filler cap C,)
fill the tank, but do not continue after the
3rdcut- off of the nozzle
; this could cause
malfunctions.
When
you have filled the tank: )
refit the filler cap, inser ting the upper par t first,
)
screw in the filler cap to the right,)
close the flap.
Ensure that the fuel filler flap is closed correctly.This symbol indicates that the
fuel
tank cap is located on the left-handside of the vehicle.
Openin
g the cap may cause an inrush of air.
This vacuum, which is completely normal, is caused by the sealing of the fuel system.