2012 PEUGEOT 4008 stop start

1
35
Instruments and controls
Screen 1Screen 2CauseSolution - ActionObservations

Warning messages (ignition at "ON")
Fault with the electric power steering. Stop the vehicle, wait few moments
then start the engine again. If the message remains after
restarting, contact a PEUGEOT
dealer or a qualified workshop.
The batter
y for the "Keyless Entry and Starting" system is flat. Replace the battery (see "Changingthe batteries").
The electronic ke
y that you have onyour person is not recognised. Check that you have the correctelectronic key. If the message persists, contact a
PEUGEOT dealer.
The electronic ke
y is still in the
vehicle and you have tried to lock
the doors or boot from the outside. Ensure that
you have the electronickey on your person before lockingthe vehicle.
One of the doors or the boot is not properly closed when locking the
vehicle from the outside. Close the door or the boot, then lock
the vehicle.
Fault with the "Ke
yless Entry andStarting" system. Contact a PEUGEOT dealer.

36
Instruments and controls
Screen 1Screen 2CauseSolution - ActionObservations
The brake fluid level is too low. Top up using a brake fluid listed by
PEUGEOT. If the problem persists, contact a PEUGEOT dealer or a qualified workshop.
Fault with the brakin
g system. You must stop as soon as it is safe
to do so. Have the system checked by a PEUGEOT dealer or a qualified workshop.
Fault with the anti-lock braking
s
ystem (ABS). Contact a PEUGEOT dealer or a qualified workshop. The vehicle retains conventional
braking without assistance but you
are advised to stop.
One of the doors or the boot is notproperly closed. Close the door or the boot. The opening in question is identified
in the screen.
The bonnet is not properly closed. Close the bonnet.
F
ault with the electronic anti-theft
system. Switch off the ignition then start the engine again. If the problem persists, contact a
PEUGEOT dealer.
The driver's door is open and theignition is still on. Switch off the ignition before leavingthe vehicle.

40
Instruments and controls
Screen 1Screen 2CauseSolution - ActionObservations
Engine oil level not correct (below minimum level or above maximum level). Stop the vehicle as soon as it is safe
to do so.
Check the level with the dipstick and
top-up if the level low.
I
f the level is above the maximum
mark, do not restar t the engine andcontact a PEUGEOT dealer or aqualified workshop. Never drive with an incorrect oil
level.
Presence of water in the Diesel fuel filter. Risk of damage to the injection system on Diesel engines. Contact a PEUGEOT dealer or
a qualified workshop as soon as possible.
The ambient temperature is at or
below 3 °C
(37 °F). There may be black ice on the road.
Take care and drive gently.
The clutch pedal is not depressed
while star tin
g the engine. Depress the clutch pedal to star t theengine. For vehicles fitted with a manual gearbox.
The gear lever is not in position P
or position N
when starting the engine. Place the gear lever at position P tostart the engine. For vehicles fitted with a CVT gearbox.
The brake
pedal is not pressed
while star ting the engine. Press the brake pedal to star t theengine.

1
55
Instruments and controls
If no action is carried out within 10 seconds, the system will exit the "Functions setting mode" menuautomatically.
)Turn button B
"TUNE" to the left or to theright to select "CT ON"
(automatic mode)or "CT OFF"(manual mode). )After selecting the mode, you can exit the "Functions setting mode" menu by pressingbutton B
"TUNE" for approximately2 seconds.
The digital clock does not display seconds.
When the "minutes" display is set or reset to zero, the clock starts at the zero second of the minute selected.
The time setting is lost if the battery is disconnected.

Manual adjustment
)
With the ignition on or in the ACC (Accessories) position, press and hold
the CLOCK
button until the time displayflashes.)
Press the appropriate button to set the
time:
ButtonH:to set the hours The hours digits scroll when you press this button. Button M:
to set the minutes
The minutes digits scroll when you press this button.
Button 00:to reset the minutes to zero.


- from 1 to 29 min:
rounded down to theprevious hour,

- from 30 to 59 min:
rounded up to the nexthour.)
After setting the time, press theDISPbutton; the time display stops flashing.
Set the time using the buttons as indicated below:

69
2
Access
Visit a PEUGEOT dealer with the vehicle's registration document and your personal identification documents and if possible the key code label.
The PEUGEOT dealer will be able to retrieve the key code and the transponder code required to order a new key.
Electronic key
The electronic key is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock the vehicle, without you being aware of it.Do not repeatedly press the buttons of your electronic key out of range and out of sight of your vehicle. You run the risk of stopping it from working and the remote control would have to be reinitialised.The electronic key cannot operate as a remote control when it is in the reader or even when the ignition is switched on.
Locking the vehicle
Driving with the doors locked may make access to the passenger compar tment by the emergency ser vices more difficult in an emergency.
As a safety precaution (with children on board), take the Keyless Entry and Star ting electronic key when you leave the vehicle, even for a shor ttime.
Electrical interference
The Keyless Entry and Starting electronic key may not operate if close to certain electronic devices: telephone, laptop computer, strong magnetic fields, ...
Anti-theft protection
Do not make any modifications to the electronic engine immobiliser system; this could cause malfunctions.Don't forget to turn the steering to engage the steering lock.
When purchasing a second-hand vehicle
Have all of the keys in your possession paired by a PEUGEOT dealer, to ensure that only your keys allow your vehicle to be unlocked and started.

73
2
Access
For all work on the alarm system, contact a PEUGEOT dealer or a qualified workshop.






Alarm * System which protects and provides a deterrent against theft and break-ins. It provides the following types of monitoring:




- perimeter

The system checks for any opening of the vehicle.
The alarm is triggered if anyone tries to open adoor, the boot, the bonnet...


- volumetric

The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compar tment or moves inside the vehicle.

- tilt

The system checks for any change in theattitude of the vehicle.
The alarm is triggered if the vehicle is lifted,moved or knocked.


Self-protection function

The system checks for the putting out of service of its components.
The alarm is triggered if the battery, the centralcontrol or the siren wiring are put out of service
or damaged.
Locking the vehicle with full
alarm system
Activation
)
Switch off the ignition (OFF mode if your
vehicle has the Keyless Entry and Star ting system).) Remove the key from the ignition switch,
if your vehicle does not have the "Keyless
Entry and Starting" system.) Leave the vehicle, and close all the doorsand the bonnet. )
Press the locking button on the remote control or one of the door or boot buttons
if your vehicle has the "Keyless Entry and Starting" system.
Deactivation

Do one of the the following to deactivate thealarm:)
Press the unlocking button on the remotecontrol or one of the door or boot buttonsif your vehicle has the "Keyless Entry andStarting" system.
)
Switch on the ignition (ON mode if your
vehicle has the "Keyless Entry andStarting" system). ) Open a door or the boot while the system is being activated.
The alarm system is deactivated: the indicator
lamp A
goes off.
The alarm is bein
g activated: the indicator
lamp A flashes rapidly accompanied byan intermittent audible signal for about
20 seconds.

Once the 20 seconds have expired, the
system is active . The audible signal stops and
the indicator lamp in the button flashes slowly.

*
According to equipment.

75
2
Access

Tr iggering of the alarm


This is indicated by sounding of the siren andflashing of the direction indicators for thirtyseconds.
A message then appears in the instrument
panel screen while the siren is operating.
When the ignition is next switched on (ONmode if your vehicle has the "Keyless Entry and Starting" system), an audible signal sounds four
times to inform you that the alarm was triggeredduring your absence.
Complete deactivation of
the alarm
)
Switch off the ignition (OFF mode if your vehicle has the "Keyless Entry andStarting" system). )
Remove the key from the ignition switch,
if your vehicle does not have the "Keyless
Entry and Star ting" system.) Open the driver's door. )
Place the lighting control stalk in the "OFF"position. )
Pull the wiper control stalk towards you and
hold.
After about ten seconds there is an audible signal.) When the audible signal stops, continue to
hold the wiper stalk pulled towards you and
press the remote control locking button.
You can completely deactivate the alarm
system. To do this, proceed as follows:
) The state of the system is then signalled to you by the number of beeps:
One beep: the alarm system is completely deactivated.
Two beeps: the alarm system is activated.
Each new press of the remote control
lockin
g button changes the state of thesystem.
It is possible to adjust the sensitivity of the alarm sensor and to deactivatethe function via the colour screen"Equipment" menu.

78
Access








Panoramic sunroof It has a motorised blind.
Motorised blind
With the ignition on, there are two ways of
opening or closing the blind:)Briefly pull or push the control indirection 1 or 2, the blind stops when you release the control. )Maintain pressure on the control in direction 1 or 2
until movement starts, the
blind then opens or closes fully.


Stopping temporarily
)
To stop the opening or closing of the blind,
press par t 3of the control or reverse themovement of the control.



Safety anti-pinch

At the end of its travel, if the blind encounters
an obstacle to closing, it stops and moves back
slightly.

Remember to always switch off theignition when leaving the vehicle, even for a short time.
When operating the control, the driver should ensure that there is nothing preventing movement of the blind.
The driver must ensure that passengersuse the blind correctly.
Be aware of children when operating the blind.