2012 PEUGEOT 4007 lock
[x] Cancel search: lockPage 26 of 236
1
INSTRUMENTS and CONTROLS
Warning lamp
is on
Cause
Actions/Observations
Driver's
seat belt not
fastened
Fixed The driver has not
fastened or has
unfastened their seat
belt. This is accompanied by a message on the
instrument panel screen.
Fasten the driver's seat belt.
ABS
Fixed This comes on if an anti-
lock braking system fault
occurs. It is accompanied by a message in the instrument
panel screen. The vehicle retains conventional
braking without assistance but you are advised to
stop. Have it checked by a PEUGEOT dealer or
a qualifi ed workshop.
Airbags and
pretensioners
Fixed This comes on for a
few seconds when the
ignition is turned to "ON"
then goes off. It should go off when the engine is started. If it
does not go off, contact a PEUGEOT dealer or a
qualifi ed workshop.
This comes on if an
airbag or pretensioner
fault occurs. It is accompanied by a message on the
instrument panel screen. Have the system
checked by a PEUGEOT dealer or a qualifi ed
workshop without delay.
Dynamic
stability control
system (ASC)
Fixed This comes on if a
dynamic stability control
system fault occurs. It is accompanied by a message on the
instrument panel screen. Have the system
checked by a PEUGEOT dealer or a qualifi ed
workshop without delay.
Page 27 of 236
1
INSTRUMENTS and CONTROLS
Each time the engine is started: a series of warning lamps and/or messages come on, applying a checking self test. They go
off after a few seconds. Engine running: the warning lamp or the message becomes a warning if it remains on continuously
or fl ashes. This initial warning may be accompanied by an audible signal and a message on the screen. Do not ignore these
warnings.
The messages displayed may differ between the type 1 instrument panel and the type 2 instrument panel.
When the cause of the appearance of the warning lamp or warning message has been rectifi ed, the warning disappears
from the screen automatically. If the cause of the warning is not rectifi ed, you can return to the previous screen at any time
by pressing the INFO
button on the dashboard.
The symbol "!"
is displayed.
To return to the previous screen (with the "!"
symbol), you must press the INFO
button several times.
INSTRUMENT PANEINSTRUMENT PANEL DISPLAYS
Warning messages (ignition at "OFF")
You can close the warning messages which show these symbols in order to move on to the next screen.
To do this, press the INFO
button according to the symbol displayed.
Press briefl y
. Press and hold
.
Symbols which appear in the top right corner of the screen.
Message
is on
Cause
Solution - action
Observations
Key in
ignition
Fixed The driver's door is open
and you have forgotten
to remove the key from
the ignition. Turn the ignition switch
to the LOCK position
and remove the key. Only if the engine has
been started.
An intermittent audible
signal is heard.
Lighting
left
on
Fixed You have forgotten to
switch off the vehicle
lighting. Switch off the vehicle
lighting by placing the
stalk at OFF. An intermittent audible
signal is heard.
Page 28 of 236
1
INSTRUMENTS and CONTROLS
Warning messages (ignition at "ON")
Message
is on
Cause
Solution - action
Observations
ABS
Fixed Anti-lock braking system
(ABS) fault. Contact a PEUGEOT
dealer or a qualifi ed
workshop.
The vehicle retains
conventional braking
without assistance but
you are advised to stop.
Braking
system
Fixed
Associated warning
lamp.
The level of brake
fl uid in the reservoir
is too low. Stop and top up, otherwise
contact a PEUGEOT
dealer or a qualifi ed
workshop. If the message remains
on after topping up,
contact a PEUGEOT
dealer or a qualifi ed
workshop.
Associated warning
lamp.
Braking system fault. Contact a PEUGEOT
dealer or a qualifi ed
workshop.
You must stop as
soon as it is safe to
do so.
Parking brake
on
Fixed You have moved off with
the parking brake still
applied. Release the parking brake.
Coolant
temperature
Flashing
High engine
temperature. If the message fl ashes
,
wait for the engine to cool
before topping up the level,
if necessary.
You must stop your
vehicle as soon as it
is safe to do so.
Flashing
If the message fl ashes
and the service warning
light comes on
, contact
a PEUGEOT dealer or
a qualifi ed workshop
without delay.
Seat belt
Fixed The driver has not fastened
or has unfastened his seat
belt. Fasten your seat belt. There is an intermittent
audible signal above
5 mph (8 km/h).
Page 32 of 236
1
INSTRUMENTS and CONTROLS
Prevention messages
Information messages (ignition at "ON")
Message
is on
Status of the system
2WD two wheel
drive system
Flashing When the "2WD" (2 wheel drive) mode is selected using
the transmission mode selector.
4WD four wheel
drive system
Flashing When the "4WD" (4 wheel drive) mode is selected using
the transmission mode selector.
This mode is the default mode.
4WD LOCK four
wheel drive system
Flashing When the "LOCK" (4 wheel drive) mode is selected using
the transmission mode selector.
Ambient
temperature
Fixed This indicates the ambient temperature.
When the vehicle is stationary or if the speed is below 12 mph
(20 km/h) the temperature displayed may not be the true
temperature.
Display
is on
Cause
Solution - action
Observations
Service
indicator
Fixed Informs the driver of
the time remaining
before the vehicle's
scheduled service. Contact a
PEUGEOT dealer
or a qualifi ed
workshop. This is displayed for a few
seconds when the ignition is
switched on.
Break
advised
Fixed Informs the driver that
they should stop to
take a break. You are advised to
take a break. This is displayed when the
driving time that you set
previously is reached.
An audible signal is heard
3 times and is then heard
every 5 minutes until the
vehicle stops.
Page 41 of 236
1
INSTRUMENTS and CONTROLS
MONOCHROME SCRCHROME SCREEN
This provides the following information:
- the time,
- audio system information (refer to
the "Audio and Telematics" section).
Setting the time
The digital clock can be set in automatic
mode
or in manual mode
.
Selecting the Setting
Select the automatic mode
or the
manual mode
as follows:
)
Press button A
"PWR" to switch on
the audio system.
)
Access the setting mode by press-
ing button B
"TUNE" for approxi-
mately 2 seconds.
)
Press button B
"TUNE" several
times to scroll through the various
menus and select the CT menu
(clock time).
The order of the menus is the
following: AF/CT/REG/TP-S/PTY
display language/SCV/PHONE/
Functions setting mode OFF.
Automatic mode
This mode permits automatic setting
of the local time using the signal from
RDS stations.
The symbol "CT"
appears on the
screen.
Manual mode
This mode permits manual setting of
the time using the audio equipment but-
tons.
It can also be used when the "Automatic
mode" displays an inaccurate time,
when the local RDS stations are broad-
casting from a different time zone.
Page 42 of 236
1
INSTRUMENTS and CONTROLS
Set the time using the buttons as indi-
cated below:
)
with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK
button until the
time display fl ashes.
)
Press the appropriate button to set
the time:
Button
H:
to set the hours
The hours digits scroll when you press
this button.
Button M:
to set the minutes
The minutes digits scroll when you
press this button.
Button 00:
to reset the minutes to
zero.
- from 1 to 29 min
:
rounded down to
the previous hour,
- from 30 to 59 min:
rounded up to
the next hour.
)
After setting the time, press the
DISP
button; the time display stops
fl ashing.
Manual mode
Automatic mode
In this mode, setting is automatic using
the signal from the RDS radio stations. The digital clock does not dis-
play seconds.
When the "minutes" display is
set or reset to zero, the clock
starts at the zero second of the
minute selected.
The time setting is lost if the bat-
tery is disconnected.
)
Turn button B
"TUNE" to the left or
to the right to select "CT ON"
(auto-
matic mode) or "CT OFF"
(manual
mode).
)
After selecting the mode, you can
exit the "Functions setting mode"
menu by pressing button B
"TUNE"
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the "Functions setting mode"
menu automatically.
Page 44 of 236
1
INSTRUMENTS and CONTROLS
Setting the time
The digital clock is set automatically
.
This mode enables the system to set
the local time automatically using the
signal from the RDS stations.
)
On the control panel, press button B
(SET) to access the "Settings"
menu.
)
On the touch screen, press button B
to access the "System"
menu.
The system settings screen is dis-
played.
"Info" menu
On the control panel, press button D
(INFO)
to access the "Info"
screen and
consult:
- "Support info"
to display the soft-
ware and data versions,
- "Vehicle position"
to display the
GPS location of the vehicle,
- "Calendar"
to make a note of
events, birthdays, etc.,
- "Journey"
to display the average
speed, fuel consumption, distances
and driving time,
- "Environment"
to display the alti-
tude, the atmospheric pressure, the
exterior temperature (the ice symbol
is displayed if there is a risk of ice),
- "Air conditioning"
to display the
information relating to the air condi-
tioning,
- "Mobile phone"
to enter a number,
delete a character, make or receive
a call.
"Route" menu
On the control panel, press button E
(NAVI)
to access the "Route Menu"
screen and select:
- "Detour"
to make a detour through
a specifi ed region,
- "Itinerary"
to change the route,
- "View route"
to display a route in
different ways,
- "Delete route"
to delete a route,
-
"Nearby POI"
to search for the
POIs in the surrounding area.
Page 56 of 236
2
COMFORT
Rear armrest
Lower the armrest to use it.
To return to the initial confi guration,
push the armrest until it locks in its ver-
tical position.
Access to the third row
The passenger gains access to the
third row of seats by tilting a second
row seat.
To put this seat back in place, refer to
the following pages.