Page 120 of 284
FITTINGS
118
BOOT FITTINGS
1.
Rear parcel shelf
2.
Hooks
3.
12 V accessory socket (120 W)
4.
Rear seats folding controls
5.
Boot
fl oor
6.
Storage well (lift the boot fl oor)
Page 121 of 284
FITTINGS
The hooks can be used to secure shop-
ping bags.
Hooks
)
To connect a 12 V accessory (max
power: 120 W), remove the cap and
connect an appropriate adaptor.
)
Turn the key to the ignition on position.
12 V accessory socket
Adjustable boot floor
)
Push the fl oor forwards, then lift up.
To place and support the fl oor at an
angle.
)
Raise the fl oor towards the rear par-
cel shelf.
)
Pass two retractable stops then
place the fl oor back on these two
stops.
Do not place more than 100 kg on the
fl oor.
Page 122 of 284
FITTINGS
Rear parcel shelf
To fold it:
)
unhook the two cords,
)
fold it concertina-style to the rear
seats.
To remove it:
)
fold the rear parcel shelf as de-
scribed above,
)
unclip the fi xings on the left and on
the right by pushing gently,
)
place your hands as shown on the
illustration then pull the assembly
towards you,
To store it at the bottom of the boot:
)
remove the rear parcel shelf as de-
scribed above,
)
push the boot fl oor towards the
bottom of the vehicle then lift it up-
wards,
)
place the rear parcel shelf ( A
) in its
location at bottom of the boot,
)
refi t the boot fl oor, the rear parcel
shelf is protected.
This consists of three sections which
can be folded back on each other.
To put it back in place:
)
remove the rear parcel shelf from its
location under the boot fl oor,
)
take hold of the rear parcel shelf
with both hands then place it on its
support,
)
unfold it to the boot pillars,
)
hook the two cords,
)
if necessary, press on the top of the
rear parcel shelf, on the left and on
the right, to engage the fi xings.
Page 123 of 284
FITTINGS
121
)
Push up the boot carpet for access
to the storage well.
Depending on the confi guration, this
has areas for storing:
- a box of spare bulbs,
- a fi rst aid kit,
- a tyre repair kit,
- a warning triangle,
- ...
Storage well
Rear side blinds
Fitted on the rear windows, these pro-
tect your young children from the sun.
)
Pull the blind by the central tab.
)
Position the blind attachment on the
hook.
Page 149 of 284
D
R
147
Emergency release
For safety reasons, after this
manoeuvre it is essential to
contact a PEUGEOT dealer
urgently to replace the protec-
tive cover.
Following an emergency unlocking,
immobilisation of the vehicle is no
longer guaranteed once the manual
emergency release has been de-
ployed and the manual control does
not allow the re-application of your
parking brake.
Take no action, either on control le-
ver A
, or stopping / starting the hybrid
system while the release device is en-
gaged.
Take care not to allow moisture or dust
in the proximity of the protective cover.
)
Immobilise the vehicle (or keep
it stationary, if the brake pedal is
pressed), with the hybrid system ac-
tive, by putting the gear selector into
position M
or R
.
)
Switch off the hybrid system but leave
the ignition on (position 2). If it is im-
possible to immobilise the vehicle, do
not action the control and urgently
contact a PEUGEOT dealer.
)
Fetch the two vehicle blocks and
the release device, located under
the boot carpet (see "Changing a
wheel" in the "Practical information"
section).
)
Immobilise the vehicle by placing
blocks in front and behind one of the
front wheels.
)
Slide the front left-hand seat back
as far as possible.
)
Lift up the fl oor plug B
in the carpet
under the seat.
)
Pierce the protective cover C
on the
tube D
with the release device.
)
Place the release device in the tube D
.
)
Turn the release device clockwise.
For safety reasons
, it is essential
to continue turning the device as far
as it will go. The parking brake is re-
leased.
)
Remove the release device and store it
with the blocks in the toolbox.
- The operation of the parking
brake reinitialises when the igni-
tion is switched off then on again.
If the reinitialisation of the parking
brake proves impossible, contact a
PEUGEOT dealer.
- The subsequent time required for ap-
plication may be longer than during
normal operation.
Front left seat moved back fully.
In the event of the electric parking brake
malfunctioning or the battery running
fl at, an emergency manual device can
release the parking brake.
Page 172 of 284
PRACTICAL INFORMATION
170
All of these tools are specifi c to your
vehicle. Do not use them for other
purposes.
1.
12 V compressor.
Contains a sealant cartridge for
the temporary repair of a tyre and
can be used to adjust the tyre
pressures.
2.
Two chocks to chock the vehicle.
3.
Socket for security bolts (located
in the glove box) * .
For adapting the wheelbrace to
the special security bolts.
List of tools
Other accessories
4.
Removable towing eye.
Refer to "Electric parking
brake" in the "Driving" section.
Refer to the paragraph "Towing
the vehicle".
5.
Electric parking brake emergency
release control.
TEMPORARY PUNCTUREREPAIR KIT
Complete system consisting of a com-
pressor and a sealant cartridge which
permits temporary repair
of a tyre so
that you can drive to the nearest ga-
rage.
It is designed to repair most punctures
which could affect the tyre, located on
the tyre tread or shoulder.
Access to the kit
This kit is installed in the storage box,
under the boot fl oor.
*
Depending on destination country.
Page 178 of 284
PRACTICAL INFORMATION
176
The tools are stowed in the boot.
Access to the tools
All of these tools are specifi c to your
vehicle. Do not use them for other
purposes.
1.
Wheelbrace. *
For removing the wheel fi xing bolts.
2.
Jack with integral handle. *
For raising the vehicle.
3a.
Wheel trim remover (depending
on equipment) * .
For removing the central wheel
trim on alloy wheels.
3b.
"Bolt cover" tool (depending on
equipment) * .
For removing the bolt protectors
(covers) on alloy wheels.
List of tools
Other accessories
4.
Centre guide * .
For refi tting an alloy wheel to the
hub.
5.
Socket for the security bolts (locat-
ed in the glove box) * .
For adapting the wheelbrace to
the special "security" bolts.
6.
Chocks to immobilise the vehicle.
7.
Removable towing eye.
See "Electric parking brake".
See "Towing the vehicle".
8.
Electric parking brake emergency
release control.
Before doing any work on your
vehicle, switch off the ignition
( Ready
lamp off) to avoid any
risk of injury resulting from automatic
operation of the engine.
When using lifting equipment
(a jack for example), take care
to use the jacking points pro-
vided, so as to avoid damaging
the high voltage cables.
CHANGING A WHEEL
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.
*
According to country of sale.
Page 180 of 284
PRACTICAL INFORMATION
178
Fitting a wheel
List of operations
)
Put the wheel in place on the hub.
)
Screw in the bolts by hand to the
stop.
)
Pre-tighten the security bolt (if your
vehicle has them) using the wheel-
brace 1
fi tted with the security socket 5
.
)
Pre-tighten the other bolts using the
wheelbrace 1
only.
)
Lower the vehicle fully.
)
Fold the jack 2
and detach it.
)
Tighten the security bolt (if your vehicle
has them) using the wheelbrace 1
fi t-
ted with the security socket 5
.
)
Tighten the other bolts using the
wheelbrace 1
only.
)
Refi t the central wheel trim then
press to clip it in place, or refi t the
bolt covers to each bolt.
)
Stow the tools.
After changing a wheel
To store the punctured wheel in the
boot correctly, fi rst remove the cen-
tral cover.
Have the tightening of the bolts and
the pressure of the spare wheel
checked by a PEUGEOT dealer with-
out delay.
Have the punctured wheel repaired
and replace it on the vehicle as soon
as possible.
