2012 NISSAN X-TRAIL light


> (GLW    0RGHO 7$@
1. Ifthe booster batteryisin another vehicle
*
B
,
position thetwo vehicles
*
A
and
*
B
to bring the
batteries intoclose proximity toeach other.
CAUTION:
If the battery ofvehicle
*
A
equipped withthe
Intelligent Keysystem isdischarged, theignition
switch cannot bemoved fromtheªLOCKº
position and,ifthe steering lockisengaged,
the steering wheelcannot bemoved. Connect
the jumper cablestothe booster vehicle
*
B
before turning orpushing theignition switchand
disengaging thesteering lock.
2. Apply theparking brake.
3. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªNº (Neutral) position.
4. Switch offallunnecessary electricalsystems
(headlights, heater,airconditioner, etc.).
5. Place theignition switchinthe ªLOCKº position.
6. Remove thevent caps, ifequipped, onthe battery .
7. Cover thebattery withafirmly wrung outmoist
cloth toreduce thehazard ofan explosion.
8. Connect thejumper cablesinthe sequence as
illustrated (
*
1
,
*
2
,
*
3
,
*
4
) .
CAUTION:
. Always connect positive +topositive +and
negative 7tobody ground, NOTto the
battery's negative7.
. Besure thatthejumper cablesdonot touch
moving partsinthe engine compartment. .
Besure thatthejumper cable's clamps do
not contact anyother metal.
9. Start theengine ofthe booster vehicle
*
B
and let
it run forafew minutes.
10. Depress theaccelerator pedalofthe booster
vehicle
*
B
at about 2,000 rpm.
11. Start theengine ofthe jumped vehicle
*
A
in the
normal manner.
CAUTION:
Never keepthestarter motorengaged formore
than 10seconds. Ifthe engine doesnotstart
right away, placetheignition switchªOFFºand
wait atleast 10seconds beforetryingagain.
12. After theengine isstarted, carefully disconnect
the jumper cablesinthe opposite sequence from
that illustrated (
*
4
,
*
3
,
*
2
,
*
1
) .
13. Remove anddispose ofthe cloth asitmay be
contaminated withcorrosive acid.
14. Replace thevent caps, ifremoved.
NO TE:
. For model withStop/Start SystemorIdling
Stop System, usethespecial batterythatis
enhanced inregard tothe charge-discharge
capacity andlifeperformance. Avoidusinga
non-special batteryforthe Stop/Start Sys-
tem orIdling StopSystem, asthis may cause
early deterioration ofthe battery oramal-
function ofthe Stop/Start SystemorIdling
Stop System. Forthebattery, itis recom-
mended touse Genuine NISSANparts.For
more information, contactaNISSAN dealer. .
For model withStop/Start SystemorIdling
Stop System, itmay take some timeuntil
Stop/Start SystemorIdling StopSystem
activates whenthebattery isreplaced orthe
battery terminal isdisconnected forex-
tended periods andthen reconnected.
In case ofemergency
6-9
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
6-10
In case ofemergency
T32A1308 27-F123FE9 F-EA80-4BD 4-8400-0FE8 D527FD22
Do not attempt tostart theengine bypushing the
vehicle.
CAUTION:
. Continuously Variable Transmission (CVT)/
Manual Transmission (MT)model cannot be
started bypushing. Attempting todo somay
cause damage tothe transmission.
. Three-way catalystequipped modelshould
not bestarted bypushing. Attempting todo
so may cause damage tothe three-way
catalyst.
. Never trytostart theengine bytowing.
When theengine starts,theforward surge
could cause thevehicle tocollide withthe
towing vehicle.
. Stop/Start SystemorIdling StopSystem
equipped modelcannot bestarted bypush-
ing the vehicle.
T32A130827- 0650D05A-CC 67-40AA-8C96-B273BCC7A50B
WARNING:
. Never continue drivingifyour vehicle over-
heats. Doingsocould cause avehicle fire.
. Never openthehood ifsteam iscoming out.
. Never remove theradiator orcoolant reser-
voir capwhile theengine ishot. Ifthe
radiator orcoolant reservoir capisremoved
when theengine ishot, pressurized hot
water willspurt outand possibly cause
burning, scalding orserious injury.
. Ifsteam orcoolant iscoming fromthe
engine, standclearofthe vehicle toprevent
getting burned.
. The engine cooling fancan start atany time
when thecoolant temperature exceedspre-
set degrees.
. Becareful nottoallow yourhands, hair,
jewelry orclothing tocome intocontact with,
or toget caught inthe cooling fanordrive
belts.
If your vehicle isoverheating (indicatedbythe high
temperature indicator),or ifyou feel alack ofengine
power, detectunusual noise,etc.,takethefollowing
steps:
1. Safely movethevehicle offthe road away from
traffic.
2. Turn onthe hazard indicator flasherlights.
3. Apply theparking brake.
4. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªNº (Neutral) position.
DO NOTST OP THE ENGINE . 5.
Open allthe windows.
6. Turn offthe airconditioner. Movethetemperature
control tomaximum hotand thefancontrol tohigh
speed.
7. Get outfrom thevehicle.
8. Visually inspectandlisten forsteam orcoolant
escaping fromtheradiator beforeopening the
hood. Wait until nosteam orcoolant canbeseen
before proceeding.
9. Open theengine hood.
10. Visually inspectifthe cooling fanisrunning.
11. Visually inspecttheradiator andradiator hosesfor
leakage.
If the cooling fanisnot running orthe coolant is
leaking, stoptheengine.
12. After theengine coolsdown, checkthecoolant
level inthe reservoir withtheengine running. Do
not open theradiator cap.
13. Add coolant tothe reservoir ifnecessary .
Have yourvehicle inspected/repaired ataNISSAN
dealer.
PUSH STARTING IFYOUR VEHICLE OVERHEA TS
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
7-2
Appear anceandcare
T32A1308 27-B546E8 D4-F62E-4E44-86B7-FD A25D20C022
In order tomaintain theappearance ofyour vehicle, itis
important totake proper careofit.
Whenever possible,parkyourvehicle insideagarage
or inacovered areatominimize thechances of
damaging thepaint surface ofyour vehicle.
When itis necessary topark outside, parkinashady
area orprotect thevehicle withabody cover. Be
careful nottoscratch thepaint surface when
putting onorremoving thebody cover.
W ASHING
T32A130827-7 5EA71EE-82C3-45D9-8 9B6-534587A2F13A
In the following instances, washyourvehicle assoon
as possible toprotect thepaint surface:
. After arainfall, whichmaycause thepaint surface
damage fromacidrain.
. After driving oncoastal roads,whichmaycause
rusting fromthesea breeze.
. When contaminants suchassoot, birddroppings,
tree sap, metal particles orbugs getonthe paint
surface.
. When dustormud builds uponthe paint surface.
1. Wash thevehicle surface withawet sponge and
plenty ofwater.
2. Clean thevehicle surface gentlyandthoroughly
using amild soap, aspecial vehiclesoapora
general purpose dishwashing liquidmixed with
clean, lukewarm (neverhot)water.
CAUTION:
. Donot wash thevehicle withstrong house-
hold soap, strong chemical detergents, ga-
soline orsolvents.
. Donot wash thevehicle indirect sunlight or
while thevehicle bodyishot, asthe paint
surface maybecome water-spotted. .
Avoid usingtight-napped orrough cloths,
such aswashing mitts.Caremust betaken
when removing caked-ondirtorother for-
eign substances sothe paint surface isnot
scratched ordamaged.
3. Rinse thevehicle thoroughly withplenty ofclean
water.
4. Use adampened chamoistodry the paint surface
and avoid leaving waterspots.
When washing thevehicle, takecare ofthe following:
. Inside flanges, jointsandfolds onthe doors,
hatches andhood areparticularly vulnerabletothe
effects ofroad salt.Therefore, theseareasmust
be cleaned regularly.
. Besure thatthedrain holes inthe lower edgeof
the doors arenot clogged.
. Spray watertothe underbody andinthe wheel
wells toloosen thedirt and/or washawayroad
salt.
REMOVING SPOTS
T32A1308 27-D69C8C6 E-23D2-464A-971C-BACAC 95FCE20
Remove tarand oilspots, industrial dust,insects, and
tree sapasquickly aspossible fromthepaint surface
to avoid lasting damage orstaining. Specialcleaning
products areavailable ataNISSAN dealerorany
automotive accessorystore.
W AXING
T32A130827- D9B96C11-516D-48E7- 8EEB-9F4E4A00E581
Regular waxingprotects thepaint surface andhelps
maintain anew vehicle appearance.
After waxing, polishing isrecommended toremove
built-up residueandtoavoid aweathered appearance.
A NISSAN dealercanassist youinchoosing the
appropriate waxingproducts.
CAUTION:
. Wash yourvehicle thoroughly andcomple-
tely before applying waxtothe paint surface.
. Always followthemanufacturer's instruc-
tions supplied withthewax.
. Donot use awax containing anyabrasives,
cutting compounds orcleaners thatmay
damage thevehicle finish.
Machine compounding oraggressive polishingona
base coat/clear coatpaint finish maydullthefinish or
leave swirlmarks.
GLASS
T32A130 827-EF64A8 17-F9D8-41D 9-9211-AFD2A86FD09E
Use glass cleaner toremove smokeanddust filmfrom
the glass surfaces. Itis normal forglass tobecome
coated withafilm after thevehicle isparked inthe hot
sun. Glass cleaner andasoft cloth willeasily remove
this film.
CLEANING EXTERIOR
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
8 Maintenance anddo-it-yourself
Maintenance requirements ....
...................................................... ..............8-2
Scheduled maintenance ....
....................................... ...........................8-2
General maintenance ....
............................................ ...........................8-2
Where togo for service ....
....................................... ...........................8-2
General maintenance ....
................................................................ ..............8-2
Explanation ofgeneral maintenance items....
................................. 8-2
Maintenance precautions....
...................................................... ..........8-4
Engine compartment checklocations ....
................................................ 8-5
QR25DE enginemodel....
................................................. ..................8-6
MR20DD enginemodel....
....................................... ...........................8-7
R9M engine model....
............................................ ...............................8-8
Engine cooling system ....
............................................ ...............................8-8
Checking enginecoolant level....
............................................ ..........8-9
Changing enginecoolant ....
...................................................... ..........8-9
Engine oil....
................................................................ ................................8-10
Checking engineoillevel ....
...................................................... .......8-10
Changing engineoiland oilfilter ....
............................................... 8-10
Protect environment ....
........................................................... ...........8-13
Drive belt....
....................................... .......................................................... 8-14
Spark plugs(gasoline enginemodels) ....
........................................... 8-14
Iridium-tipped sparkplugs ....
............................................ ...............8-14
Brakes ....
............................................ .......................................................... 8-15
Checking parkingbrake....
....................................... ........................8-15
Checking footbrake pedal ....
.......................................................... 8-15
Brake booster ....
................................................. ................................8-15
Brake fluid....
................................................. .............................................8-16
Clutch fluid(ifequipped) ....
....................................... ............................8-17
Continuously Variable Transmission (CVT)fluid(ifequipped) ....
.... 8-17
Air cleaner filter....
............................................ .........................................8-17Wiper
blades ....
................................................................ ........................8-18
Windshield wiperblades ....
............................................ ...............8-18
Rear window wiperblade ....
......................................................... 8-19
Window washerfluid....
........................................................... ...............8-19
Battery ............................................................... .........................................8-20
V ehicle battery ....
...................................................... ........................8-20
Remote controller battery....
.......................................................... 8-21
Intelligent Key battery ....
...................................................... ...........8-22
V ariable voltage controlsystem (ifequipped) ....
.............................. 8-23
Fuses ....
...................................................... .................................................8-24
Engine compartment ....
....................................... ............................8-24
Passenger compartment ....
................................................. ...........8-24
Lights ....
............................................ .......................................................... 8-27
Headlights ....
............................................ .........................................8-27
Exterior lights....
....................................... ......................................... 8-28
Interior lights....
................................................. ................................8-29
Light locations ....
...................................................... ........................8-30
Legal requirement toadjust headlight beam....
........................ 8-33
Tires andwheels ....
...................................................... ............................8-36
Tire Pressure Monitoring System(TPMS) (ifequipped) ....
.... 8-36
Tire inflation pressure ....
...................................................... ...........8-36
T ypes oftires ....
....................................... ......................................... 8-36
Tire chains ....
............................................ .........................................8-36
Tire rotation ....
........................................................... ........................8-37
Tire wear anddamage ....
....................................... ........................8-37
Tire age ....
................................................. .........................................8-37
Changing tiresandwheels ....
............................................ ...........8-37
Wheel balance ....
................................................. ............................8-38
Spare tire(ifequipped) ....
...................................................... .......8-38
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
8-2
Mainten anceanddo-it-yo urself
T32A130827- 0502B887-92 93-4255-B737-1A75B9 EBE59B
Some day-to-day andregular maintenance isessential
to maintain yourvehicle's goodmechanical condition,
as well asitsemission andengine performance.
It is the owner's responsibility tomake surethatthe
specified maintenance, aswell asgeneral mainte-
nance, isperformed.
As the vehicle owner,youaretheonly onewho can
ensure thatyour vehicle receives theproper main-
tenance care.
SCHEDULED MAINTENANCE
T32A1308 27-1AF9EF DF-11D3-4E79-A687-B 1800356718 0
For your convenience, therequired scheduled main-
tenance itemsaredescribed andlisted inaseparate
W arranty Information andMaintenance booklet.You
must refertothat booklet toensure thatnecessary
maintenance isperformed onyour vehicle atregular
intervals.
GENERAL MAINTENANCE
T32A1308 27-21A9EC DE-764E-44 8F-9627-03CA CE492717
General maintenance includesthoseitemswhich
should bechecked duringnormal day-to-day operation
of the vehicle. Theyareessential ifyour vehicle isto
continue tooperate properly.It is your responsibility to
perform theseprocedures regularlyasprescribed.
Performing generalmaintenance checksrequires
minimal mechanical skillandonly afew general
automotive tools.
These checks andinspections canbedone by
yourself, aqualified technician, orifyou prefer, a
NISSAN dealer.
WHERE TO GO FOR SERVICE
T32A130827- E992BEEB-58F2-4980-B 85D-7522676C7996
If maintenance serviceisrequired oryour vehicle
appears tomalfunction, havethesystems checked and
tuned byan authorised NISSANdealer.
T32A1308 27-336118 83-3F4A-4D 74-9C04-47 9B9B808DE 3
During normal day-to-day operationofthe vehicle,
general maintenance shouldbeperformed regularlyas
prescribed inthis section. Ifyou detect anyunusual
sounds, vibrations orsmells, besure tocheck forthe
cause orhave aNISSAN dealerdoitpromptly .In
addition, youshould notifyaNISSAN dealerifyou think
that repairs arerequired.
When performing anychecks ormaintenance work,
closely observe ªMaintenance precautionsº(P.8-4) .
EXPLANA TIONOFGENERAL MAINTE-
NANCE ITEMS
T32A130 827-9E64D 705-5D51-4 EF3-B757-C 014C6BA1081
Additional information onthe following items
with ª*ºisfound laterinthis section.
Outside vehicle
T32A1308 27-3B6990FC-07B7- 4E4D-A8A2 -E7502A73D 704
The maintenance itemslisted hereshould beper-
formed fromtimetotime, unless otherwise specified.
Doors andhood:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Check thatalldoors andthehood operate smoothly as
well asthe back door, trunklidand hatch. Alsomake
sure thatalllatches locksecurely .Lubricate if
necessary .Make surethatthesecondary latchkeeps
the hood fromopening whentheprimary latchis
released. Whendriving inareas usingroadsaltor
other corrosive materials, checklubrication frequently.
Lights*:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Clean theheadlights onaregular basis.Makesurethat
the headlights, stoplights, taillights, turnsignal lights,
and other lights arealloperating properlyandinstalled
securely .Also check theaim ofthe headlights.
MAINTENAN CEREQUIREME NTS GENERALMAINTENANCE
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
Tires*:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Check thepressure withagauge oftenandalways
prior tolong distance trips.Adjust thepressure inall
tires, including thespare, tothe pressure specified.
Check carefully fordamage, cutsorexcessive wear.
Tire rotation*:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
In the case thatTwo-Wheel Drive(2WD) andfront &
rear tires aresame size;Tires should berotated every
10,000 km(6,000 miles).
Tires marked withdirectional indicatorscanonly be
rotated between frontandrear.
Make surethatthedirectional indicatorspointinthe
direction ofwheel rotation afterthetire rotation is
completed.
In the case thatFour-Wheel Drive(4WD) andfront &
rear tires aresame size;Tires should berotated every
5,000 km(3,000 miles).
Tires marked withdirectional indicatorscanonly be
rotated between frontandrear.
Make surethatthedirectional indicatorspointinthe
direction ofwheel rotation afterthetire rotation is
completed.
In the case thatfront tiresaredifferent sizefrom rear
tires; Tirescannot berotated.
However, thetiming fortire rotation mayvaryaccording
to your driving habitsandtheroad surface conditions.
Tire Pressure Monitoring System(TPMS)trans-
mitter components (ifequipped) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Replace theTPMS transmitter grommetseal,valve
core andcap when thetires arereplaced duetowear
or age. Wheel
alignment andbalance:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
If the vehicle shouldpulltoeither sidewhile driving on
a straight andlevel road, orifyou detect uneven or
abnormal tirewear, theremaybeaneed forwheel
alignment. Ifthe steering wheelorseat vibrates at
normal highway speeds,wheelbalancing maybe
needed.
Windshield:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Clean thewindshield onaregular basis.Check the
windshield atleast every sixmonths forcracks orother
damage. Repairasnecessary .
Wiper blades*:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Check forcracks orwear ifnot functioning correctly.
Replace asnecessary .
Inside vehicle
T32A130827-9 2ACDC4E-987C-49DA-8D8E-20CE2 0E92881
The maintenance itemslistedhereshould bechecked
on aregular basis,suchaswhen performing periodic
maintenance, cleaningthevehicle, etc.
Accelerator pedal:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Check thepedal forsmooth operation andmake sure
that thepedal doesnotcatch orrequire uneven effort.
K eep thefloor mats away fromthepedal.
Brake pedal*:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Check thepedal forsmooth operation andmake sure
that itis the proper distance fromthefloor matwhen
depressed fully.Check thebrake booster function. Be
sure tokeep thefloor mats away fromthepedal.
Parking brake*:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Check theparking brakeoperation regularly.Check
that thelever (ifequipped) orthe pedal (ifequipped)
has theproper travel.Alsomake surethatthevehicle is
held securely onafairly steep hillwhen onlythe
parking brakeisapplied. Seat
belts:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Check thatallparts ofthe seat beltsystem (for
example, buckles,anchors, adjusters andretractors)
operate properly andsmoothly ,and areinstalled
securely .Check thebelt webbing forcuts, fraying,
wear ordamage.
Steering wheel:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Check forchanges inthe steering condition, suchas
excessive play,hard steering orstrange noises.
Warning lightsandchimes:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Make surethatallwarning lightsandchimes are
operating properly.
Windshield defogger:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Check thattheaircomes outofthe defogger outlets
properly andingood quantity whenoperating the
heater orair conditioner.
Windshield wiperandwasher*:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Check thatthewipers andwasher operate properly
and that thewipers donot streak.
Under hoodandvehicle
T32A1308 27-7742FF 9D-6320-4F0 D-86C0-408787680914
The maintenance itemslistedhereshould bechecked
periodically (forexample, eachtimeyoucheck the
engine oilorrefuel) .
Battery*:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Except formaintenance freebattery ,check thefluid
level ineach cell.Itshould bebetween theªUPPERº
and ªLOWERº lines.Vehicles operated inhigh
temperatures orunder severe conditions require
frequent checksofthe battery fluidlevel.
Maintenan ceand do-it-you rself
8-3
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
8-12
Maintenance anddo-it-yours elf
JVM0421X
MR20DD engine
*
1
Oil filler cap
*
2
Oil drain plug
*
3
Oil filter
1. Place alarge drainpanunder thedrain plug.
2. Remove thedrain plugwithawrench.
3. Remove theoilfiller capand completely drainthe
oil.
If the oilfilter isto be changed, removeand
replace itat this time.
CAUTION:
Waste oilmust bedisposed ofproperly. Check
your local regulations.
4. Remove theplastic coverovertheoilfilter location
by removing thesmall plastic clipsasillustrated.
(For QR25DE engine)
5. Loosen theoilfilter withanoilfilter wrench.
6. Remove theoilfilter byturning itby hand.
7. Wipe theengine oilfilter mounting surfacewitha
clean cloth.
Be sure toremove anyoldgasket remaining onthe
mounting surface. 8.
Apply newengine oiltothe gasket ofthe new oil
filter.
9. Screw inthe oilfilter untilaslight resistance isfelt
and then tighten anadditional 2/3ofaturn to
secure thefilter.
Oil filter tightening torque:
15 to20 N´m
(1.5 to2.0 kg-m, 11to15 ft-lb)
10. Clean andreinstall thedrain plugandnew washer.
Securely tightenthedrain plugwithawrench. Do
not use excessive force.
Drain plugtightening torque:
29 to39 N´m
(3.0 to4.0 kg-m, 22to29 ft-lb)
11. Refill therecommended engineoiland quantity .
(See ªRecommended Fluids/lubricants andcapa-
citiesº (P.9-2) .)
When fillingtheengine oil,donot remove
the dipstick.
12. Securely installtheoilfiller cap.
13. Start theengine.
14. Check thedrain plugforany sign ofleakage.
15. Dispose ofthe used oilinthe proper manner.
Check yourlocal regulations.
16. Check theengine oillevel according tothe proper
procedure. (SeeªChecking engineoillevelº (P.8-
10) .) R9M
engine:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVM0436X
*
1
Oil filler cap
*
2
Oil drain plug
*
3
Oil filter
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
SDI2149
1 Oilfiller element
2 O-ring
3 Oilfilter cover
1. Place alarge drainpanunder thedrain plug.
2. Remove thedrain plugwithawrench.
3. Remove theoilfiller capand completely drainthe
oil.
If the oilfilter isto be changed, removeand
replace itat this time.
CAUTION:
Waste oilmust bedisposed ofproperly. Check
your local regulations.
4. Loosen theoilfilter cover withawrench.
5. Remove theengine oilfilter cover thentheoilfilter
element.
6. Remove therubber O-ring fromthefilter cover.
7. Wipe theentire oilfilter cover withaclean cloth.
Be sure toremove anyoldO-ring remaining onthe
mounting surface. 8.
Apply newengine oiltothe O-ring.
Install thenew O-ring onthe new oilfilter element.
9. Insert theoilfilter element intotheengine oilfilter
cover.
10. Screw inthe oilfilter cover untilaslight resistance
is felt, and then tighten thefilter completely .
Oil filter cover tightening torque:
25 N´m
(2.6 kg-m, 18ft-lb)
11. Clean andreinstall thedrain plugandnew washer.
Securely tightenthedrain plugwithawrench. Do
not use excessive force.
Drain plugtightening torque:
50 N´m
(5.1 kg-m, 36.9ft-lb)
12. Refill therecommended engineoiland quantity .
(See ªRecommended Fluids/lubricants andcapa-
citiesº (P.9-2) .)
13. Securely installtheoilfiller cap.
14. Start theengine.
15. Check thedrain plugforany sign ofleakage.
16. Dispose ofthe used oilinthe proper manner.
Check yourlocal regulations.
17. Check theengine oillevel according tothe proper
procedure. (SeeªChecking engineoillevelº (P.8-
10) .)
After operation
T32A1308 27-3D1A869 1-255E-47E3-9C50-DDE5 E8CFBD36
1. Lower thevehicle carefully tothe ground.
2. Dispose ofwaste oiland filter properly .
PRO TECT ENVIRONMENT
T32A1308 27-208605 74-F3E8-4014 -8CD9-B62C347302 4F
It is illegal topollute drains,watercourses andsoil. Use
authorized wastecollection facilities,including civil
amenity sitesandgarages providing facilitiesfor
disposal ofused oiland used oilfilters. Ifin doubt,
contact yourlocal authority foradvice ondisposal.
The regulations concerningthepollution ofthe
environment willvary from country tocountry.
Maintenance anddo-it-yours elf
8-13
&RQGLWLRQ
([FHSWIRU&KLQD