2012 NISSAN MAXIMA light

Black plate (70,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
4-8
Setting destinationINFO:
Subcategories may not exist depending on
the category that is selected.
7. Enter the name of the destination facility and highlight [List], and then push .
The facility list is displayed.
INFO:.
It is not necessary to enter the facility name completely. It is also possible to
display the list screen only by highlighting
[List] without entering the facility name
and pushing .
.
The number of narrowed down points are
displayed in the “Matches” column.
.
Up to two keywords (part of the facilityname) can be entered by highlighting
[AND Search] and pushing
after entering the first facility name.
INFO:
The facility name can also be entered
directly by highlighting [Choose Name] on
the main category list screen and pushing
.
8. Highlight the preferred destination from the
list, and push .
INFO:.
By highlighting [Sort] and pushing
, options can be sorted from
[By Name] or [By Dist.]. When selecting
[By Dist.], the position of the selected
location is displayed in the preview on
the right side of the screen.
.
In some cases, when a facility name has been entered, the number of matching
destinations in the “Matches” column
may be different from the number dis-
played on the list screen. If this occurs,
enter more characters to further reduce
the number of matches.
.
The search conditions can be changedby highlighting [Refine].
9. The entire route is shown on the map. Highlight [Start] after confirming the location
of the displayed destination and push
. The system sets the destination

Black plate (71,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
to the selected location and starts calculat-
ing a route.INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.
“Procedures after setting destination”
(page 5-2)
Searching for restaurant by ZAGAT1. Push .
2. Highlight [Places] and push .
3. Highlight [ZAGAT] and push .4. Highlight the preferred state and push
. A list screen is displayed.
5. Highlight the preferred city and push
. A list screen is displayed.6. Highlight [RESTAURANT] and push
. A list screen is displayed.7. Highlight the preferred category and push
. A list screen is displayed.
Setting destination
4-9

Black plate (72,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
4-10
Setting destination
8. Highlight the preferred sorting order and push . A list screen is displayed.9. Highlight the preferred destination facility
from the list, and then push .
INFO:.
By highlighting [Sort] and pushing
, sorting options can be se-
lected to re-sort the list.
.
The search conditions can be changed by highlight [Refine].
.
By highlighting [Ratings] and pushing , an explanation of the ZAGAT
ratings can be displayed.
10. The entire route is shown on the map. Highlight [Start] after confirming the location
of the displayed destination and pushing
. The system sets the destination
to the selected location and starts calculat-
ing a route.
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc..
“Procedures after setting destination”
(page 5-2)
*
C2009 Zagat Survey, LLC. Zagat Survey is a
registered trademark of Zagat Survey, LLC
SETTING HOME AS DESTINATIONThe home location can be set as the destination
to which the system calculates a route. This
function is especially useful when searching for
a route to return to the home location.1. Push .
2. Highlight [Home] and push .3. The home location is displayed and set as
the destination.

Black plate (73,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
INFO:
If the home location is not stored yet, the
system will automatically display a screen for
storing it.
“Storing location” (page 6-2)
4. The entire route to home is shown on the map. Highlight [Start] after confirming the
location of the displayed destination, and
push . The system sets the
destination to the selected location and
starts calculating a route.
Voice command
1. Push >located on the steering
wheel switch.
2. After the tone sounds, speak a command.
To set the home location as the destination:
“Navigation” “Destination Home” (Standard
mode) “Destination Home” (Alternate command mode)
SEARCHING FROM ADDRESS BOOKA location stored in the Address Book can be
set as the destination to which the system
calculates a route. To utilize this function more
effectively, destinations that are often traveled to
should be stored in advance.1. Push
.
2. Highlight [Address Book] and push . A list screen is displayed.
3. Highlight the preferred location from the list
and push .
INFO:
Selecting [Sort] displays a list of various sort
functions. To use the sort functions, stored
locations must be set in advance.
“Storing location” (page 6-2)
INFO:*1
Sort by Number:
The Address Book entries are displayed
in ascending numerical order.
*2
Sort by Name:
The Address Book entries are displayed
in alphabetic order.
*3
Sort by Icon:
By selecting a particular icon, a list that
contains only the Address Book entries
Setting destination
4-11

Black plate (74,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
4-12
Setting destinationassociated with that icon is displayed.
*4
Sort by Group:
By selecting a particular group (family,
friends, leisure, etc.) , the selected group
is displayed at the top of the list.
4. The entire route is shown on the map. Highlight [Start] after confirming the location
of the displayed dest ination, and push
. The system sets the destination
to the selected location and starts calculat-
ing a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can
be stored, etc.“Procedures after setting destination”
(page 5-2)
Voice command
1. Push >located on the steering
wheel switch.
2. After the tone sounds, speak a command.
To set the destination from the Address Book:
“Navigation” “Address Book” (Standard mode)
“Address book” (Alternate command mode)
SETTING PREVIOUS DESTINATIONA previously set destination can be set again as
the destination to which the system calculates a
route. Up to 300 previous destinations will be
automatically stored.
If the number of previous destinations exceeds
300, the oldest one will be replaced by the new
one.1. Push .
2. Highlight [Previous Destinations] and push . A list screen is displayed.
3. Highlight the preferred destination from the
list and push .
INFO:
By highlighting [By Date], the list can be
sorted in chronological order. By highlight-
ing [By Name], it can be sorted in alphabe-
tical order.
4. The entire route is shown on the map. Highlight [Start] after confirming the location
of the displayed dest ination, and push
. The system sets the destination

Black plate (75,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
to the selected location and starts calculat-
ing a route.INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can
be stored, etc.“Procedures after setting destination”
(page 5-2)Voice command
1. Push >located on the steering
wheel switch.
2. After the tone sounds, speak a command.
To display the Previous Destinations list:
“Navigation” “Previous Destinations” (Standard
mode)
“Previous Destinations” (Alternate command
mode)
SETTING PREVIOUS START POINTThe start point of the previous route guidance
can be set as the destination to which the
system calculates a route.
1. Push .
2. Highlight [Next Page] and push .3. Highlight [Previous Start Point] and push
.
4. The previous start point is set as a destina-
tion, and the entire route is shown on the
map. Highlight [Start] after confirming the
location of the displayed destination, and
push . The system sets the
destination to the selected location and
starts calculating a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can
be stored, etc.“Procedures after setting destination”
(page 5-2)Voice command
1. Push >located on the steering
wheel switch.Setting destination
4-13

Black plate (76,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
4-14
Setting destination
2. After the tone sounds, speak a command.
To set the previous start point as the destination:
“Previous Start Point” (Alternate command
mode)SETTING FROM STORED ROUTESA preferred route can be selected from the
stored routes.1. Push .
2. Highlight [Next Page] and push .
3. Highlight[StoredRoutes]andpush
. A list screen is displayed.4. Highlight the preferred route from the list
and push . The route to the
destination is set.5. The entire route is shown on the map. Highlight [Start] after confirming the location
of the displayed dest ination, and push
. The system sets the destination
to the selected location and starts calculat-
ing a route.
INFO:
. Even after setting a destination, the location
of the destination can be adjusted, the
location can be stored, etc.
“Procedures after setting destination”
(page 5-2)
. The stored route includes only locations
(destination and waypoints) and route cal-
culation conditions, not the route itself.
Therefore, when the destination is set using
a stored route, a different route may be
suggested if the current vehicle location is
different from the one when the route was
stored.
SETTING BY PHONE NUMBERIf the telephone number of the facility is
available, use this to find the facility by entering
the number, and then have the system calculate
a route.
INFO:
. Telephone numbers that were stored for
stored destinations can also be used.
. If the area code of the specified telephone
number does not exist in the map data, the
system will not search for the location.

Black plate (77,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
. Only the locations included in the database
in the map data can be searched by the
phone number. Residential phone numbers
cannot be used to search for a location.1. Push .
2. Highlight [Next Page] and push .3. Highlight [Phone Number] and push
. The telephone number input
screen is displayed.
4. Enter the telephone number including the area code.
5. After finishing the entry, highlight [List] and push .
“Number input screen” (page 2-15)
6. Displays a list screen if there are two or
more search results. Highlight the preferred
destination from the list and push
.
A confirmation screen for the place name
and the location is displayed, and the system
starts calculating.
7. The entire route is shown on the map. Highlight [Start] after confirming the location
of the displayed dest ination, and push
. The system sets the destination
to the selected location and starts calculat-
ing a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can
be stored, etc.“Procedures after setting destination”
(page 5-2)
SETTING FREEWAY ENTRANCE/EXITThe entrance or exit of a freeway can be set as
the destination to which the system calculates a
route.
Setting destination
4-15