Page 201 of 610
3-104 Features and controls
3
If you turn the steering wheel while the vehicle is station-
ary with the headlights on, the headlights may become
dim. This behaviour is not abnormal. The headlights will
return to their original brightness after a short while.Electric power steering system warning displayTy p e 1
Ty p e 2
If there is a malfunction in the system, the warning display will
appear on the information screen in the multi-information dis-
play.
If the warning display appears while driving 1. Stop the vehicle in a safe place and turn off the engine.
2. Wait approximately 30 seconds and then restart the engine
to check whether the warning display goes out; if it then
remains off, there is no problem.
If the warning display does not go out, or it appears again
while driving, have the vehicle inspected at an authorized
Mitsubishi Motors dealer or a repair facility of your
choice.
CAUTION
!If the warning display appears during driving, it
may become harder to turn the steering wheel.
BK0140300US.book 104 ページ ２０１１年６月２８日 火曜日 午後５時１８分
Page 203 of 610
3-106 Features and controls
3
Traction control function
N00559200076
On slippery surfaces, the traction control function prevents the
drive wheels from spinning excessive, thus helping the vehicle
to start moving from a stopped condition. It also provides suffi-
cient driving force and steering performance as the vehicle
turns while pressing the acceleration pedal.Skid control function
N00559300051
The skid control function is designed to help the driver main-
tain control of the vehicle on slippery roads or during rapid
steering maneuvers. It works by controlling the engine output
and the brake on each wheel.NOTEThe skid control function operates at speeds of about 9
mph (15 km/h) or higher.
ASC OFF switch
N00559400241
The ASC is automatically activated when the ignition switch is
turned to the “ON” position or the operation mode is put in
ON. You can deactivate the system by pressing down the “ASC
OFF” switch for 3 seconds or longer.
When the ASC is deactivated, the display/indicator will turn
on. To reactivate the ASC, momentarily press the “ASC OFF”
switch ; the display/indicator is turned off.
CAUTION
!When driving a vehicle on a snowy or icy road, be
sure to install snow tires and drive the vehicle at
moderate speeds.
BK0140300US.book 106 ページ ２０１１年６月２８日 火曜日 午後５時１８分
Page 218 of 610
Features and controls
3-121
3
If the warning light/display illuminates while
driving
N00532800471
1. If the tire pressure monitoring system warning light illu-
minates, avoiding hard braking, sharp steering maneuvers
and high speeds. You should stop and adjust the tires to
the proper inflation pressure as soon as possible. Adjust
the spare tire at the same time. Refer to “Tires” on page 7-
23.NOTEIn addition, the warning display is displayed on the infor-
mation screen in the multi-information display.
When inspecting or adjusting the tire pressure, do not
apply excessive force to the valve stem to avoid breakage.
After inspecting or adjusting the tire pressure, always
reinstall the valve cap on the valve stem.
Without the valve cap, dirt or moisture could get into the
valve, resulting in damage to the tire inflation pressure
sensor.
Do not use metal valve caps, which may cause a metal
reaction, resulting in corrosion and damage of the tire
inflation pressure sensors.
Once adjustments have been made, the warning light will
go off after a few minutes of driving.2. If the tire pressure monitoring system warning light
remains illuminated after you have been driving for about
20 minutes after you adjust the tire inflation pressure, one
or more of the tires may have a puncture. Inspect the tire
and if it has a puncture, have it repaired by an authorized
Mitsubishi Motors dealer as soon as possible.
WA R N I N G
!If the warning light/display illuminates while you
are driving, avoid hard braking, sharp steering
maneuvers and high speeds.
Driving with an under-inflated tire adversely affects
vehicle performance and can result in an accident.
CAUTION
!If a tire has a puncture, replace that tire with the
spare tire. Driving on a punctured tire could lead to
an accident.The warning light/display may not illuminate imme-
diately in the event of a tire blowout or rapid leak.
BK0140300US.book 121 ページ ２０１１年６月２８日 火曜日 午後５時１８分
Page 266 of 610
Features and controls
3-169
3
—The F. A. S. T. -key is not detected.Insert the F. A. S. T. -key into the key
slot in the glove compartment. Refer to
“If the F. A. S. T. -key is not operating
properly” on page 3-28.
—You have forgotten to remove the F. A.
S. T. -key from the key slot in the glove
compartment.Remove the F. A. S. T. -key from the
key slot in the glove compartment.
—The steering wheel is locked.Press the engine switch.
Refer to “Steering wheel lock” on page
3-26.
—The engine switch is pressed to stop
the engine and the selector lever is in a
position other than the “P” (PARK)
position.On vehicles with CVT, place the selec-
tor lever in the “P” (PARK) position to
put the operation mode in OFF.
—The driver’s door is opened with the
steering wheel unlocked.Refer to “Steering wheel lock” on page 3-
26.
Screen type 1
Screen type 2
Cause
Do this (Reference)
BK0140300US.book 169 ページ ２０１１年６月２８日 火曜日 午後５時１８分
Page 268 of 610
Features and controls
3-171
3
Warning display list (With ignition switch or operation mode is in ON)
N00558100254
Screen type 1
Screen type 2
Cause
Do this (Reference)
There is a fault in the EPS.Park your vehicle in a safe place and
inspect it.
If the light still illuminates after the
inspection, contact an authorized Mit-
subishi Motors dealer or a repair facil-
ity of your choice for assistance.
Refer to “Electric power steering sys-
tem (EPS)” on page 3-103.
BK0140300US.book 171 ページ ２０１１年６月２８日 火曜日 午後５時１８分
Page 271 of 610
3-174 Features and controls
3
The engine hood is open.Close the engine hood.
Refer to “Engine hood” on page 7-4.
—There is a fault in the electronic immo-
bilizer (Anti-theft starting system).Put the operation mode in OFF, and
then start the engine again.
If the warning is not cancelled, please
contact an authorized Mitsubishi
Motors dealer or a repair facility of
your choice.
—The driver’s door is open when the
operation mode is in any mode other
than OFF.Put the operation mode in OFF.
Refer to “Changing the operation
mode” on page 3-23.
—There is a fault in the steering wheel
lock.Park your vehicle in a safe place as
soon as possible and contact an autho-
rized Mitsubishi Motors dealer or a
repair facility of your choice to have
the system checked.
—There is a fault in the electrical system.Park your vehicle in a safe place as
soon as possible and contact an autho-
rized Mitsubishi Motors dealer or a
repair facility of your choice to have
the system checked.
Screen type 1
Screen type 2
Cause
Do this (Reference)
BK0140300US.book 174 ページ ２０１１年６月２８日 火曜日 午後５時１８分
Page 294 of 610
Features and controls
3-197
3 Turn signal lever
N00522600450
When changing lanes, or to making a gradual turn, hold the
lever in the “lane change” position (1). It will return to the neu-
tral position when you let go. Use the full position (2) when
making a normal turn. The lever will return to the neutral posi-
tion when the turn is complete. There may be times when the
lever does not return to the neutral position. This usually hap-
pens when the steering wheel is turned only slightly. You can
easily return the lever by hand.
Also, when you move the lever to (1) slightly then release it,
the turn signal lights and the indicator light in the instrument
cluster will flash three times.
NOTEA light in the instrument panel flashes to show when the
front and rear turn signal lights are working properly.
If this light flashes faster than usual, check for a burned
out turn signal light bulb or malfunctioning connection in
the signal.
If the panel light does not come on when the lever is
moved, check for a blown fuse or a burned out bulb in the
panel.
Have the system inspected by your authorized Mitsubishi
Motors dealer or a repair facility of your choice.
It is possible to modify functions as follows:
• Deactivate the turn signal light 3-flash function for lane
changes.
• Adjust the time required to operate the lever for the 3-
flash function.
See your authorized Mitsubishi Motors dealer for details.
For vehicles equipped with the Mitsubishi Multi-Commu-
nication System, adjustments can be made using screen
operations. For further details, refer to the separate
owner’s manual.
BK0140300US.book 197 ページ ２０１１年６月２８日 火曜日 午後５時１８分
Page 306 of 610
Features and controls
3-209
3
NOTEAs your vehicle is equipped with heated mirrors, mist can
also be removed from the outside rearview mirrors when
the rear window defogger switch is pressed. (Refer to
“Door mirror heater” on page 3-67.)
Horn switch
N00523800172
To honk the horn, press around the “ ” mark on the steering
wheel.
CAUTION
!The rear window defogger is not designed to melt
snow. Remove any snow manually before using the
rear window defogger.Use the rear window defogger only after the engine
has started and is running. Be sure to turn the
defogger switch off immediately after the window is
clear to save on battery power.Do not place stickers, tape, or other items that are
attached with adhesive over the grid wires on the
rear window.When cleaning the inside rear window, use a soft
cloth and wipe lightly over the grid wires.
BK0140300US.book 209 ページ ２０１１年６月２８日 火曜日 午後５時１８分
