2012 MITSUBISHI OUTLANDER SPORT ignition

5
The sunshade can be operated with the ignition switch or the operation mode in ON.
A - Pull the switch in the arrow direction to
open the sunshade. Pulling the switch all
the way automatically opens the sunshade
completely.
B - Push the switch in the arrow direction to close the sunshade. Pulling the switch all the way
automatically closes the sunshade completely.
C - Push the switch to stop the moving sunshade. If an object obstructs the sunshade from
closing the safety mechanism will cause the sunshade to re-open automatically. The
opened sunshade will become operational again after a few seconds.
The sunshade illumination turns on with the ignition switch or when the operation mode is in ON or ACC.
D - Push the switch to change brightness of the sunshade illumination. The brightness switches in sequence from
high → middle → low → off → high.
A
- Turn for Temperature control
B - Push to select outside air (Indicator light off) or recirculated air
(Indicator light on)
C - Turn to select the blower speed. To the right increases blower speed. To
the left decreases blower speed. Turned all the way to the left turns the
blower off. Note: OFF is located above AUTO.
D - Push for air conditioning ON/OFF (Indicator light on/Indicator light off).
E - Turn to select the air flow and direction mode (AUTO position is only auto type air conditioning).
F - Push to defog the rear window (Indicator light on). Rear window
defogger light automatically turns off after 20 minutes.
To defog front windshield
1. Set the Mode Dial E to defrost
position.
2. Set the blower speed C to the maximum position.
3. Set the temperature A to highest position.
Air Conditioning (Automatic shown) The wipers will operate once.
INT: Intermittent intervals can be
adjusted by turning the knob A
AUTO: The wipers will be
operated automatically by rain
sensor (if so equipped).
Slow
FastWindshield Wipers
CONTROLS
Sunshade
Turn the knob B to operate the
rear window wiper.
The wiper operates
continuously for several
seconds then operates
intermittently at intervals of
about 8 seconds.
Washer fluid is sprayed,
the wiper will automatically
operate 2 or 3 times.
Rear Window Wiper/Washer
Rain Sensing Wipers
(if equipped)
It is possible to adjust the
sensitivity of the rain sensor by
turning the AUTO ring (C).
+ Higher sensitivity to rain
— Lower sensitivity to rain
C
A
D
B
C

6OWN THE ROAD
A - CANCEL: To deactivate the cruise control
B - ACC RES: To increase the set speed or resume previously
set cruise control operation.
C - COAST SET: To set the desired speed and to reduce
the set speed
D - ON/OFF: To turn ON/OFF cruise control
To set a cruising speed
1. Press D and the CRUISE
indicator light in the meter
cluster will be turned on.
2. Accelerate or decelerate to your desired speed (above
25 mph). Press C and remove your foot from the
accelerator pedal.
To accelerate or decelerate speed
Press B to increase set cruising speed.
Press C to decrease set cruising speed.
To cancel the cruising speed
Press A or press brake pedal, or press D .
– :SHIFT DO WN+ :SHIFT UP
Paddle Shifters (if equipped) Drive Mode Selector (if equipped) The drive mode can be switched by turning the
dial while the ignition switch is in the ON position.
The following drive modes are available:
2WD: This mode is for economical driving on
normal dry roads and freeways.
4WD AUTO: This mode is for all driving
conditions on various roads.
4WD LOCK: This mode is for driving in slippery conditions such as on
snow-covered roads or sand.
Cruise Control
A
Clock
To set the time
1. Press and hold A and the clock display
flashes.
2. Press C to set the “Hours”.
3. Press D to set the “Minutes”.
4. Press B to stop the clock display from
flashing.
ABCD
B
C
D
Simply upshift or
downshift with a
tap of your fingers,
without moving
your hands from the
steering wheel.
You can return to the
automatic shifting
mode by pulling the
+ (SHIFT UP) side
paddle shifter towards
you and holding for
over 2 seconds.
Seat Heater Switch Position - Action
1 (HI) - For quick heating
2 - Heater off
3 (LO) - To keep the seat warm
ECO Driving
When the ECO indicator light is on,
your current driving style supports
good fuel economy. ECO light will
only work in a normal mode. It will
not illuminate in either Sport Mode
or with Cruise Control on.

7AUDIO SYSTEM
1. Press the LOAD button E briefly.
2. The autochanger will show WAIT on the display and start making
itself ready for disc loading.
3. When the autochanger is ready for disc loading, the LOAD
indicator will illuminate and the display will show
LOAD DISC No. (1-6).
4. When a disc is inserted into the CD slot, the disc will begin to
play.
NOTE: Please refer to Comfort Controls in your Owner’s
Manual for more detailed information on how to use
your audio system.
USB and iPod® Input (if equipped)
Storing a Station to Memory
Loading a CD Audio Remote
Control Switch (if equipped)
VOLUME UP
DOWNSEEK
Change
station or
track
MODE
Change
the audio
source
1. Park your vehicle in a safe place and turn the ignition to the
lock position.
2. Connect the cable
 (cable purchased separately) to the USB
memory device
 or the Dock connector  to the iPod® .
3. Open the cover
 in the glove compartment. Connect the
cable
 to the USB input terminal .
4. Turn the ignition switch to the “ACC” position. Press A to turn
on the audio system.
5. Press the CD button B several times to switch to the USB
mode. The input mode changes as follows:
CD
 USB  Bluetooth® (if equipped)
6. Depending on your USB device, it may take longer for
playback to start. The number of songs in the device will
determine the length of time it takes to load. Typical
times are from 1 minute to 8 minutes.
7. Once the device is selected, playback starts.
NOTE: You can select desired tracks from
the “Playlist”, “Artists”, “Album”
or “Songs” menus stored in your
iPod® or desired folder in your USB
memory device. Turn the FOLDER
knob C to the desired location then
press it in to select your folder.
A
E
BC
To enter frequencies
into the memory
(AM/FM/SAT)
1. Press A to turn on
the audio system.
2. Press B to select
the desired band
(AM/FM/SAT).
3. Turn C to the
desired frequency
you wish to keep
in the memory.
4. Press one of the Memory select buttons D (1-6) until it beeps.
Your station is now stored in that location.
D








11Bluetooth® Operation with FUSE Hands-free Link System™ (if so equipped)
Making a call by using the telephone number:
1. Press A button and Say “Dial.”
2. The voice guide says “Number please.”
3. Say the telephone number “XXX•••••••.”
4. The voice guide says “Dialing .”
Making a call using a phonebook:
1. Press A button and Say “Call.”
2. After the voice guide says “Name please.”
Say the name you want to call “XXX•••••••.”
3. If there is only 1 match, the voice guide says “Calling
” and then the system will dial the telephone
number.
Receiving calls:
1. If an incoming phone call is received while the ignition
switch is in the “ACC” or “ON” position, with the audio
system OFF, the audio system automatically turns ON.
2. Press B button.
Hanging up a call:
1. Press C button.
To import a devices phonebook:
1. Press A button and Say “Phonebook.”
2. The voice guide will say “Select one of the following: new
entry, edit number, edit name, list names, delete, erase all,
or import contact.” Say “Import contact.”
3. The voice guide will say “Would you like to import a single
entry or all contact?” Say “All contacts.”
4. The voice guide will say “Importing the contact list
from the mobile phonebook. This may take several
minutes to complete. Would you like to continue?”
Answer “Yes.”
5. When the import is complete, the voice guide
will say “Import complete.”
Tip on Getting Started:
Before using FUSE for the first time, press the SPEECH button and
say “Help”. This will walk you through some tips and help set-up your
recognition profile.
For a list of compatible Bluetooth® devices please go to
http://www.mitsubishicars.com/MMNA/jsp/owners-site/technology-
features.do
If you are having difficulties operating your
phone or connecting to the system, please call
Mitsubishi Handsfree at (888) 702-4100.
SPEECH button:
Change to voice
recognition. Pushing
this button initiates
the bluetooth system.
The system asks for a
command.
PICK-UP button:
Answer an incoming call
HANG-UP button
End a call or voice
recognition
A
B
C
A
B
C
To pair a Bluetooth® enabled device:
1.
Park your vehicle in a safe location. Pairing can not be done while
vehicle is moving.
2. Press A button and Say “Setup.”
3. Say “Pairing Options.”
4. The voice guide says: “Select one of the following: pair, edit, delete, or list.”
5. Say “Pair.”
6. The voice guide says “Please say a 4-digit pairing code.”
7. Say a 4-digit number “XXXX.”
8. When the confirmation function is on, the system will confirm
whether the number said is acceptable. Answer “Yes.”
9. The voice guide says “Start pairing procedure on the device. See the device manual for instructions.” Enter in the Bluetooth® device
the 4-digit number you have registered in step 8.