2012 MITSUBISHI LANCER RALLIART brake

3-152 Features and controls
3
NOTE
An operation noise may be emitted from the engine com-
partment in the following situations. The sound is associ-
ated with checking the operations of the ASC. At this
time, you may feel a shock from the brake pedal if you
depress it. These do not indicate a malfunction.
• When the ignition switch is set to the “ON” position.
• When the vehicle is driven for a while after the engine is
turned on.

When the ASC is activated, you may feel a vibration in
the vehicle body or hear a whining sound from the engine
compartment.
This indicates that the system is operating normally. It
does not indicate a malfunction.

When the anti-lock braking system warning light is illu-
minated, the ASC is not active.Traction control function
N00559200034
On slippery surfaces, the traction control function prevents the
drive wheels from spinning excessive, thus helping the vehicle
to start moving from a stopped condition. It also provides suffi-
cient driving force and steering performance as the vehicle
turns while pressing the acceleration pedal.
Skid control function
N00559300035
The skid control function is designed to help the driver main-
tain control of the vehicle on slippery roads or during rapid
steering maneuvers. It works by controlling the engine output
and the brake on each wheel.NOTE
The skid control function operates at speeds of about 9
mph (15 km/h) or higher.
CAUTION
!
When driving a vehicle on a snowy or icy road, be
sure to install snow tires and drive the vehicle at
moderate speeds.
BK0138600US.book 152 ページ ２０１１年７月１７日　日曜日　午後２時３２分

3-154 Features and controls
3
ASC operation display or ASC OFF display
N00559500183
NOTE
The combination of items shown on the display varies
depending on the vehicle model.
NOTE
The display/indicator may come on when you start the
engine. This means that the battery voltage momentarily
dropped when the engine was started. It does not indicate
a malfunction, provided that the display goes out immedi-
ately.

When a spare tire has been put on your vehicle, the grip-
ping ability of the tire will be lower, making it more likely
that the display/indicator will blink.
-ASC operation display/ASC indicator
The display/indicator will blink when the ASC is operat-
ing.
-ASC OFF display/ASC OFF indicator
This display/incicator will turn on when the ASC is
turned off with the “ASC OFF” switch.
CAUTION
!
When display/indicator blinks, ASC is operating,
which means that the road is slippery or that your
vehicle’s wheels are beginning to slip. If this hap-
pens, drive slower.
If the temperature in the braking system continues
to increase due to continuous brake control on a
slippery road surface, the display/indicator will
blink. To prevent the brake system from overheat-
ing, the brake control of the traction control func-
tion will be temporarily suspended. The engine
control of the traction control function and normal
brake operation will not be affected. Park your vehi-
cle in a safe place. When the temperature in the
braking system has come down, the display/indi-
cator will be turned off and the traction control
function will start operating again.
BK0138600US.book 154 ページ ２０１１年７月１７日　日曜日　午後２時３２分

3-158 Features and controls
3

Your speed may increase to more than the set speed on a
steep downhill. You must use the brake to control your
speed.Cruise control switchesA- “ON OFF” switch
To activate and deactivate the cruise control function.
B- “COAST SET” switch
To reduce the set speed and to set the speed of constant-speed
driving.C- “ACC RES” switch
To increase the set speed and to resume to the previous set
speed.
D- “CANCEL” switch
To terminate constant-speed driving.
NOTE
When operating the cruise control switches, correctly
press each cruise control switch.
The cruise control may be turned off automatically if two
or more of the cruise control switches are pressed at the
same time.
Ty p e 1
Ty p e 2BK0138600US.book 158 ページ ２０１１年７月１７日　日曜日　午後２時３２分

3-162 Features and controls
3
To decrease the set speed
N00518600260
There are 2 ways to reduce the set speed.“COAST SET” switchPress and hold the “COAST SET” switch (B), the speed will
slow down (coast) gradually.
When you reach your desired speed, release the “COAST
SET” switch. Your cruising speed is now set.
To decrease the speed in small amounts, press the “COAST
SET” switch (B) for less than 1 second and release it. Everytime you press the “COAST SET” switch (B), the speed will
decrease by approximately 1 mph (1.6 km/h).
Brake pedalPress the brake pedal (which disengages the cruise control) and
when the desired speed is reached, press the “COAST SET”
switch (B) and release the switch momentarily to set a new
desired cruise speed.
Ty p e 1
Ty p e 2
Ty p e 1
Ty p e 2
BK0138600US.book 162 ページ ２０１１年７月１７日　日曜日　午後２時３２分

Features and controls
3-163
3
To temporarily increase or decrease the speed
N00518700128
To temporarily increase the speedPress the accelerator pedal as you would normally. When you
release the pedal, you will return to your set speed.
To temporarily decrease the speedApply the brakes to decrease the speed. To return to the previ-
ously set speed, press the “ACC RES” switch (C). Refer to “To
resume the set speed” on page 3-165.
Ty p e 1
Ty p e 2
BK0138600US.book 163 ページ ２０１１年７月１７日　日曜日　午後２時３２分

3-164 Features and controls
3
To deactivate
N00518800493
The cruise control can be turned off as follows:

Press the “ON OFF” switch (A). (Cruise control will be
turned off.)

Press the “CANCEL” switch (D).

Depress the brake pedal or lightly tap it.
The cruise control will be turned off automatically in the fol-
lowing conditions:
When you depress the clutch pedal (on vehicles with man-
ual transaxle).

Your speed slows to about 10 mph (15 km/h) or more
below the set speed because of an uphill, etc.

Your speed slows to about 25 mph (40 km/h) or less.

When the Twin Clutch SST control mode is set to “Sport”
mode (on vehicles with Twin Clutch SST).
Refer to “Twin Clutch SST control mode” on page 3-120.

When the active stability control (ASC) starts operating
(if so equipped).
Refer to “Active stability control (ASC)” on page 3-151.Ty p e 1
Ty p e 2BK0138600US.book 164 ページ ２０１１年７月１７日　日曜日　午後２時３２分

Features and controls
3-201
3
Changing the function settings (With ignition
switch in the “ON” position)
N00556800084
1. Park your vehicle in a safe place.
Fully apply the parking brake and move the shift lever
into the “N” position (manual transaxle), the selector lever
{continuously variable transmission (CVT)} or the gear-
shift lever (Twin Clutch SST) into the “P” position.
2. When you lightly press the multi-information meter
switch, the information screen changes to the function set-
ting screen.
Refer to “Information screen (With ignition switch in the
“ON” position)” on page 3-189.3. Press and hold the multi-information meter switch (for
about 2 seconds or more) to switch from the setting mode
screen to the menu screen.
Type 1 Type 2
CAUTION
!
For safety, stop the vehicle before operating.
While driving, even if you operate the multi-infor-
mation meter switch, the function setting screen is
not displayed.Ty p e 1
Ty p e 2
BK0138600US.book 201 ページ ２０１１年７月１７日　日曜日　午後２時３２分

Features and controls
3-215
3 Indicator light, warning light, and information screen display list
N00557700035
Indicator and warning light list
N00557800238
Ty p e A Ty p e B1- Position indicator → P.3-228
2- High beam indicator → P.3-228
3- Charging system warning light → P.3-230
4- Turn signal indicator/hazard warning light → P.3-228
5- Front fog light indicator (if so equipped) → P.3-228
6- Anti-lock braking system warning light → P.3-148
7- Tire pressure monitoring system warning light → P.3-167
8- Brake warning light → P.3-228
9- Cruise control indicator (if so equipped) → P.3-159
10- Seat belt reminder/warning light → P.2-18
11- Supplemental Restraint System (SRS) warning light
→ P.2-4312- ECO mode indicator (if so equipped) → P. 3 - 1 9 6
13- Engine malfunction indicator (“SERVICE ENGINE SOON”
or “Check engine light”) → P.3-229
14- Active stability control (ASC) OFF indicator (if so
equipped) → P. 3 - 1 5 4
15- Active stability control (ASC) indicator (if so equipped) →
P.3-154
16- Information screen display list → P.3-216
BK0138600US.book 215 ページ ２０１１年７月１７日　日曜日　午後２時３２分