2012 MITSUBISHI iMiEV maintenance

7-12 Vehicle care and maintenance
7Brake fluid
N00938700261
To check the fluid levelThe brake fluid level must be between the “MAX” and “MIN”
marks on the reservoir.
The brake fluid level falls slightly with wear of the brake pads,
but this does not indicate any abnormality.
The brake fluid in the master cylinder should be checked when
doing other work under the hood. The brake system should also
be checked for leaks at the same time.
If the brake fluid level falls markedly in a short length of time,
it indicates a leak in the brake system.
If this occurs, have the vehicle checked by a certified i-MiEV
dealer.
Fluid typeUse the recommended brake fluid conforming to DOT 3 or
DOT 4. The reservoir cap must be tightly sealed to keep dirt
and water out.
CAUTION
!
Do not let any petroleum-based fluid touch, mix
with, or get into the brake fluid. This will damage
the seals.
Be careful when handling brake fluid. It can damage
painted surfaces.
Use only the listed brake fluid. Different brands of
brake fluid have different additives, and these can
cause a chemical reaction. Do not mix brands of
brake fluid.
Keep the reservoir tank cap closed to keep the brake
fluid from evaporating.
BK0140800US.book 12 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-13
7 12V starter battery
N00939100914
The condition of the 12V starter battery is very important to
keep the vehicle’s electrical system working properly. Check
the 12V starter battery regularly. Removing and installing the 12V starter battery
upper cover
N00901300054
To r e m o v e1. Turn the plastic nut (A) counterclockwise, and then
remove the 12V starter battery upper cover (B).NOTE
Be careful not to lose the removed plastic nut.
To i n s t a l l1. Install the 12V starter battery upper cover (B) onto the
12V starter battery, and then push the plastic nut (A) in the
direction shown by the arrows to secure the cover.
BK0140800US.book 13 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-14 Vehicle care and maintenance
7
NOTE
Be sure to install the plastic nut in the correct direction.Checking 12V starter battery electrolyte level
N00901500056
Before checking the 12V starter battery electrolyte level,
remove the 12V starter battery’s upper cover.
The electrolyte level must be between the limits shown on the
outside of the 12V starter battery. Fill it with distilled water as
needed. The inside of the 12V starter battery is divided into
several compartments. Take the cap off of each compartment
and fill to the mark.
Do not fill above the top line because a spill during driving
could cause damage.
CAUTION
!
Be sure to install the 12V starter battery upper
cover. Otherwise, the battery electrolyte may spill
and cause a malfunction.
When installing the 12V starter battery upper cover
and plastic nut do not touch the cooling fan or other
moving parts under the hood.
Be especially careful that the cables, your clothing
or hair, etc., do not get caught in the cooling fan or
other moving parts.
WA R N I N G
!
If the 12V starter battery goes flat, be sure to check
the 12V starter battery electrolyte level before con-
necting booster cables.
After checking the 12V starter battery electrolyte
level, make sure the caps are fitted securely.
If any of the caps cannot be re-secured to the 12V
starter battery, replace the 12V starter battery.
BK0140800US.book 14 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-15
7
During cold weather
N00901600057
The 12V starter battery is weaker in cold temperatures. This
has to do with its chemical and physical properties and is why a
very cold 12V starter battery, especially one with a low charge,
will have a hard time starting your vehicle.
It is recommended that you have your 12V starter battery and
charging system checked by a certified i-MiEV dealer before
the start of cold weather. If necessary, have it charged. This
will guarantee more reliable starting, and longer 12V starter
battery life.

Electrolyte (battery acid) is made of corrosive
diluted sulfuric acid. If it spills on nearby parts, it
can crack, stain, or discolor them. And if gets on
your skin or in your eyes, it can cause burns or
blindness. Please observe the following handling
instructions:
• If electrolyte gets on plastic parts or other nearby
parts, wipe it off with a soft cloth or chamois
soaked in a solution of water and neutral detergent
then immediately rinse the affected parts with
plenty of water.
• If electrolyte gets on your hands or clothes, rinse
thoroughly with water. If electrolyte gets in your
eyes, flush them with water immediately and get
immediate medical attention.WA R N I N G
!
BK0140800US.book 15 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-16 Vehicle care and maintenance
7
Disconnection and connection
N00901700058
To disconnect the 12V starter battery cable, stop the electric
motor. Disconnect the negative (-) terminal first, then the posi-
tive (+) terminal. To reconnect the 12V starter battery, first
connect the positive (+) terminal and then the negative (-) ter-
minal, before starting the vehicle. NOTE
Remove the 12V starter battery upper cover before dis-
connecting the terminal of 12V starter battery. Refer to
“Removing and installing the 12V starter battery upper
cover” on page 7-13.

Open the terminal cover (A) before disconnecting or con-
necting the positive (+) terminal of the 12V starter battery.
Loosen the nut (B), and then disconnect the 12V starter
battery cable from the positive (+) terminal.
WA R N I N G
!
Never disconnect the 12V starter battery while the
electric motor unit is running, or you could damage
the vehicle’s electrical parts.
Never short-circuit the 12V starter battery. This
could cause it to overheat and be damaged.
Keep sparks, cigarettes, and flames away from the
12V starter battery because the 12V starter battery
could explode.
When installing the 12V starter battery, start con-
nection with the positive (+) terminal. If connection
is started from the negative (-) terminal, sparks will
occur if the positive (+) terminal touches any other
parts, and this may cause the 12V starter battery to
explode.
BK0140800US.book 16 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-17
7
NOTE
Before cleaning the 12V starter battery, tighten all the
filler port caps to keep dirt and moisture out.

Check each 12V starter battery terminal for corrosion. If
necessary, clean the terminals with a solution of baking
soda and water. Grease the posts and clamps after clean-
ing or tightening them.

Check to see that the 12V starter battery is securely
installed and cannot be moved. Also check each terminal
for tightness.

If you will not be driving your vehicle for a long period of
time, remove the 12V starter battery and store it in a place
where the 12V starter battery fluid will not freeze. Mem-
ory data for settings made by the user may be erased when
the 12V starter battery is removed. If this happens, reset
the settings again using the relevant procedures. The 12V
starter battery only should be stored with a full charge.
WA R N I N G
!
Open doors and windows in any closed space where
you may be charging or working with the 12V
starter battery.
Always wear protective clothing and goggles when
working with the 12V starter battery, or have a
skilled automobile technician do it.
If you are quick-charging your 12V starter battery,
first disconnect the 12V starter battery cables.
In order to prevent a short circuit, be sure to discon-
nect the negative (-) terminal first, and reconnect it
last.
If the electrolyte level is very low, have the 12V
starter battery checked at a certified i-MiEV dealer.
12V starter battery terminals and related accesso-
ries contain lead and lead compounds. Wash hands
after handling.
CAUTION
!
When replacing the 12V starter battery, remove the
connected positive (+) and negative (-) terminals
after turning the electric motor switch to the
“LOCK” position and waiting at least 1 minute. If
the 12V starter battery terminal is removed just
after the electric motor switch is turned to the
“LOCK” position, this may cause damage to compo-
nents of the electric motor unit.
BK0140800US.book 17 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-18 Vehicle care and maintenance
7Tires
N00939200540
It is important to familiarize yourself with the following terms:

Cold tire pressure:
• The measured pressure after the vehicle has been parked
for at least three hours,
or
• The measured pressure when the vehicle is driven less
than 1 mile (1.6 km) after having been parked for three
hours.

Maximum inflation pressure: the maximum permissible
cold tire inflation pressure for this tire.

Recommended inflation pressure: the inflation pressure
for optimum tire performance.
Intended outboard sidewall:
• The sidewall that contains a whitewall, bears white let-
tering or bears manufacturer, brand, and/or model name
molding that is higher or deeper than the same molding
on the other sidewall of the tire,
or
• The outward facing sidewall of an asymmetrical tire that
has a particular side that must always face outward
when mounted on a vehicle.

Passenger car tire: a tire intended for use on passenger
cars, multipurpose passenger vehicles, and trucks, that
have a gross vehicle weight rating (GVWR) of 10,000
pounds or less.

Light truck (LT) tire: a tire designated by its manufacturer
as primarily intended for use on lightweight trucks or mul-
tipurpose passenger vehicles.

Tread: portion of a tire that comes into contact with the
road.

Tread rib: a tread section running circumferentially
around a tire.

Tread separation: pulling away of the tread from the tire
carcass.

Carcass: the tire structure, except tread and sidewall rub-
ber which, when inflated, bears the load.

Sidewall: portion of a tire between the tread and bead.

Section width: the linear distance between the exteriors of
the sidewalls of an inflated tire, excluding elevations due
to labeling, decoration, or protective bands.

Bead: the part of the tire that is made of steel wires,
wrapped or reinforced by ply cords and that is shaped to
fit the rim.

Ply: a layer of rubber-coated parallel cords.
WA R N I N G
!
Driving with tires that are worn, damaged or
improperly inflated is dangerous.
These type tire conditions will adversely affect vehi-
cle performance.
These type tire conditions can also cause a tread sep-
aration or blowout which may result in an accident
causing serious injury or death.
Tires degrade over time with age even when they are
not being used. It is recommended that tires over 6
years generally be replaced even if damage is not
obvious.
BK0140800US.book 18 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-19
7

Cord: the strands forming the plies in the tire.

Rim: a metal support for a tire or a tire and tube assembly
upon which the tire beads are seated.

Rim diameter: nominal diameter of the bead seat.

Groove: the space between two adjacent tread ribs.Tire Markings
Size Designation
EXAMPLE:P215/65R15

NOTE

European/Japanese metric tire sizing is based on
European/Japanese design standards. Tires designed
to these standards have the tire size molded into the
sidewall beginning with the section width. The letter
“P” is absent from this tire size designation. Exam-
ple: 215/65R15 96H.


LT (Light Truck) -metric tire sizing is based on
U.S.A. design standards. The size designation for
LT-metric tires is the same as for P-metric tires
except for the letters “LT” that are molded into the
sidewall preceding the size designation. Example:
LT235/85R16.
PPassenger car tire size based on U.S.A. design
standards
215 Section width in millimeters (mm.)
65Aspect ratio in percent (%)
Ratio of section height to section width of tire.
RConstruction code
• “R” means radial construction.
• “D” means diagonal or bias construction.
15 Rim diameter in inches (in)
BK0140800US.book 19 ページ ２０１１年９月２９日　木曜日　午後３時２８分