2012 MITSUBISHI iMiEV change time

3-8 Features and controls
3
To l o c k Press the LOCK button (1) to lock all the doors and the liftgate.
If the dome light switch is in the door position, the dome light
will blink once. The turn signal lights will also blink once. NOTE
If you press the LOCK button (1) after locking the doors
and the liftgate, the horn will sound once to confirm that
they are locked.To unlock Press the UNLOCK button (2) to unlock the driver’s door only.
Within about 2 seconds, press the UNLOCK button one more
time to unlock all the doors and the liftgate.
If the dome light switch is in the door position, the dome light
will turn on for about 30 seconds. The turn signal lights will
also blink twice.NOTE
If the UNLOCK button (2) is pressed and no door or
liftgate is opened within about 30 seconds, relocking will
automatically occur.

The door and liftgate unlock function can be set so that all
doors and liftgate unlock when the UNLOCK button (2) is
pressed once.
For details, please contact a certified i-MiEV dealer.Answerback function The keyless entry system answerback functions from the horn
can each be turned on or off as desired.
Horn deactivation/reactivationThe horn answerback function can be set to the following three
conditions.
Each time the horn answerback function is set, a chime will
sound to tell you the condition of the answerback function.
1. Remove the key from the electric motor switch.
2. Open the driver’s door and turn the combination head-
lights and dimmer switch to the “OFF” position.
3. Press the LOCK button (1) for 4 to 10 seconds and press
the UNLOCK button (2) during this time.
4. Release in sequence the UNLOCK and LOCK buttons
within 10 seconds of pressing the UNLOCK button in step
3.Changing the setting of the turn signal lights answer-
back functionThe turn signal lights answerback function can be changed.
If you want to change the answerback function, please contact
a certified i-MiEV dealer for details.Number of
chimes
Condition
One chime The horn will not sound.
Two chimes The horn will sound.
Three chimesThe horn will sound if the auto light switch is
ON (if so equipped).
Four chimesThe horn will sound if the LOCK button is
pressed twice quickly.
BK0140800US.book 8 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-61
3
Odometer/Trip odometer/Dash lights brightness
indicator/Service reminder/Cruising range indi-
cator/Outside temperature display
N00519500439
With the electric motor switch in the “ON” position, odometer,
trip odometer, dash lights brightness indicator, service
reminder, cruising range indicator, and outside temperature are
displayed.To change the display
N00572200015
The display is changed every time the reset button (A) is
briefly pressed.
BK0140800US.book 61 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-64 Features and controls
3
1. The display shows the driving distance or number of
months remaining until the next periodic inspection.
2. This informs you that a periodic inspection is due. Contact
a certified i-MiEV dealer to have the system checked.
At this time, a spanner mark is shown for a few seconds
whenever the electric motor switch is turned from the
“LOCK” position or the “ACC” position to the “ON”
position.3. After your vehicle is inspected at a certified i-MiEV
dealer, it displays the time and miles (km) until the next
periodic inspection.
NOTE
The indicated distance decreases in steps of 100miles
(100 km). The indicated number of months decreases in
steps of one month.

It is possible to change the settings for the service
reminder.
For further information, we recommend you to consult a
certified i-MiEV dealer.
Driving distance
Number of monthsBK0140800US.book 64 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-65
3
Resetting the service reminder
With the electric motor switch in the “LOCK” position or the
“ACC” position, it is possible to reset the spanner mark (A)
and “------” indication (B).
When they have been reset, the driving distance or number of
months remaining until the next periodic inspection are shown
and the spanner mark (A) is no longer shown every time the
electric motor switch is turned from the “LOCK” position or
the “ACC” position to the “ON” position.1. Push the reset button (D) to view the driving distance or
number of months remaining until the next periodic
inspection.
2. Give the reset button (D) a long push (at least 2 seconds)
to make the spanner mark (A) start flashing. (If you do not
touch the reset button for about 10 seconds while the
spanner mark is flashing, the display will revert to its orig-
inal indication.)
3. Give the reset button (D) a gentle push while the spanner
mark is flashing. The “------” indication (B) will change to
“cLEAr” (C).
4. The driving distance or number of months remaining until
the next periodic inspection will be shown.
NOTE
It is not possible to reset the “------” indication (B) with
the electric motor switch in the “ON” position.

When a certain distance has been driven and a certain
period has elapsed after appearance of the “------” indica-
tion (B), the indication is automatically reset and the num-
ber of months until the next periodic inspection is shown.

If you accidentally reset the display, consult a certified
i-MiEV dealer for assistance.
CAUTION
!
The customer is responsible for making sure that
regular inspections and maintenance are performed.
Inspections and maintenance must be performed to
prevent accidents and malfunctions.
BK0140800US.book 65 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-66 Features and controls
3
Dash lights brightness indicator
N00572600019
Each time you press the dash lights illumination button (B), the
brightness of the instruments changes.
NOTE
You can adjust to 4 different levels for when the parking
lights or headlights are illuminated and 4 for when they
are not.

If you press and hold the button for longer than about 1
second, the brightness automatically scrolls through its
different levels, and stops scrolling when you release the
button. Select your desired level of brightness.

When the combination headlights and dimmer switch is in
the “AUTO” position, the meter illumination switches
automatically to the adjusted brightness, depending on the
brightness outside the vehicle.

The brightness level of the instruments is stored when the
electric motor switch is turned off.

If the 12V starter battery is disconnected for a long time,
these level of brightness will be reset.
A- Brightness display
B- Dash lights illumination button
Bright Dim
BK0140800US.book 66 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-82 Features and controls
3Turn signal lever
N00522600506
When changing lanes, or to making a gradual turn, hold the
lever in the “lane change” position (1). It will return to the neu-
tral position when you let go. Use the full position (2) when
making a normal turn. The lever will return to the neutral posi-
tion when the turn is complete. There may be times when the
lever does not return to the neutral position. This usually hap-
pens when the steering wheel is turned only slightly. You can
easily return the lever by hand.
Also, when you move the lever to (1) slightly then release it,
the turn signal lights and indicator in the instrument cluster will
flash three times.
NOTE
A light in the instrument panel flashes to show when the
front and rear turn signal lights are working properly.
If this light flashes faster than usual, check for a burned
out light bulb or malfunctioning connection.
If the panel light does not come on when the lever is
moved, check for a blown fuse or a burned out bulb in the
panel.
Have the vehicle inspected by a certified i-MiEV dealer.

It is possible to modify functions as follows:
• Deactivate the turn signal light 3-flash function for lane
changes.
• Adjust the time required to operate the lever for the 3-
flash function.
See a certified i-MiEV dealer for details.
BK0140800US.book 82 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-94 Features and controls
3
Voice recognition function
N00564100031
The Bluetooth
® 2.0 interface is equipped with a voice recogni-
tion function.
Simply say voice commands and you can perform various
operations and make or receive hands-free calls.
With the Bluetooth
® 2.0 interface, voice recognition is possible
for US English, North American Spanish, Canadian French and
Japanese. The factory setting is “English.”
NOTE
If the voice command that you say differs from the pre-
defined command or cannot be recognised due to ambient
noise or some other reason, the Bluetooth
® 2.0 interface
will ask you for the voice command again up to 3 times.

For best performance and further reduction of ambient
noise, the vehicle windows should be closed while engag-
ing the voice recognition function.

Depending on the selected language, some functions may
not be available.
Selecting the language1. Press the SPEECH button.
2. Say “Setup.”
3. Say “Language.”
4. The voice guide will say “Select a language: English,
Spanish, French or Japanese.” Say the desired language.
(Example: “English”)
5. The voice guide will say “English (Spanish, French or
Japanese) selected. Is this correct?” Say “Yes.”
If you say “No,” the system will return to Step 4.NOTE
The voice guide will repeat the same message twice. The
first message is in the current language, and the second
message is in the selected language.

If many entries are registered in the vehicle phonebook,
changing the language will take a longer time.

Changing the language deletes the mobile phonebook
imported to the Bluetooth
® 2.0 interface. If you wish to
use it, you will have to import it again.
6. When the voice guide says “English (Spanish, French or
Japanese) selected,” the language change process will be
completed and the system will return to the main menu.
BK0140800US.book 94 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-98 Features and controls
3
6. When all enrollment commands have been read out, the
voice guide will say “Speaker enrollment is complete.”
The system will then end the speaker enrollment process
and return to the main menu.NOTE
Completing the speaker enrollment process will turn on
the voice model automatically.

The commands “Help” and “Cancel” will not work in this
mode.Enabling and disabling the voice model and retraining
N00564900013
You can turn a voice model registered with the speaker
enrollment function on and off whenever you want.
You can also retrain the system.
Use the following procedure to perform these actions.
1. Press the SPEECH button.
2. Say “Voice training.”
3. If you have completed a speaker enrollment process once
already, the voice guide will say either “Enrollment is
enabled. Would you like to disable or retrain?” or “Enroll-
ment is disabled. Would you like to enable or retrain?”
4. When enrollment is “enabled,” the voice model is on;
when enrollment is “disabled,” the voice model is off. Say
the command that fits your needs.
Say “Retrain” to start the speaker enrollment process and
recreate a new voice model. (Refer to “Speaker
enrollment” on page 3-97.）
Connecting the Bluetooth
® 2.0 interface and
Bluetooth
® device
N00565000079
Before you can make or receive hands-free calls or play music
using the Bluetooth
® 2.0 interface function, you must pair the
Bluetooth
® device and Bluetooth
® 2.0 interface.
NOTE
Pairing is required only when the device is used for the
first time. Once the device has been paired with the
Bluetooth
® 2.0 interface, all you need is to bring the
device into the vehicle next time and the device will con-
nect to the Bluetooth
® 2.0 interface automatically (if sup-
ported by the device).
Up to 7 Bluetooth
® devices can be paired with the Bluetooth
®
2.0 interface.
If multiple paired Bluetooth
® devices are available in the vehi-
cle, the cellular phone or music player most recently connected
is automatically connected to the Bluetooth
® 2.0 interface.
You can also change a Bluetooth
® device to be connected.
NOTE
Please go to following website for a lot of compatible
devices.
www.mitsubishifuse.com
Or contact Mitsubishi hands-free customer support at
(888)702-4100.
BK0140800US.book 98 ページ ２０１１年９月２９日　木曜日　午後３時２８分