2012 MITSUBISHI GALANT turn signal

Features and controls
3-83
3
3. The light will automatically turn off after 3 minutes.NOTE
When the driver’s door is opened, a continuous high-
pitched tone will sound if the key has been removed; a
continuous low-pitched tone will sound if the key is in the
ignition switch.
The tone stops sounding when the driver’s door is closed.Headlight reminder buzzer
N00549800141
If the driver’s door is opened with the key in the “LOCK” or
“ACC” position or removed from the ignition switch while the
lights are on, the tone will sound to remind you to turn off the
lights. The lights will turn off automatically and so will the
tone. Or you can turn the light switch to the “OFF” position to
stop the tone.
Dimmer (high/low beam change)
N00549900126
To change the headlights from high beam to low beam and vice
versa, pull the turn signal lever to fully toward you (1). Switch
the headlights to low beam as a courtesy whenever there are
oncoming vehicles, or when there is traffic moving ahead of
you. An illuminated blue light in the instrument cluster indi-
cates when the headlights are on high beam.
BK0139500US.book 83 ページ ２０１１年４月１９日　火曜日　午後１時４８分

3-84 Features and controls
3
Headlight flasher
N00550000169
You can flash the high beams by pulling the lever gently
toward you (2). The lights will go back to normal when you let
go. While the high beam is on, you will see a blue light on the
instrument panel.NOTE
You can flash the high beams by pulling the lever toward
you, even if the light switch is off.

If you turn the lights off with the headlights set to high-
beam illumination, the headlights are automatically
returned to their low-beam setting when the light switch is
next turned to the “ ” position.
Turn signal lever
N00522600434
When changing lanes, or to making a gradual turn, hold the
lever in the “lane change” position (1). It will return to the neu-
tral position when you let go. Use the full position (2) when
making a normal turn. The lever will return to the neutral posi-
tion when the turn is complete. There may be times when the
lever does not return to the neutral position. This usually hap-
pens when the steering wheel is turned only slightly. You can
easily return the lever by hand.
BK0139500US.book 84 ページ ２０１１年４月１９日　火曜日　午後１時４８分

Features and controls
3-85
3
NOTE
A light in the instrument panel flashes to show when the
front and rear turn signal lights are working properly.
If this light flashes faster than usual, check for a burned
out lamp bulb or malfunctioning connection.
If the panel light does not come on when the lever is
moved, check for a blown fuse or a burned out bulb in the
panel.
Have the vehicle inspected by an authorized Mitsubishi
Motors dealer or a repair facility of your choice.

For vehicles equipped with the Mitsubishi Multi-Commu-
nication System, Mitsubishi Multi-Communication Sys-
tem can be used to select whether the tone will sound or
not sound when the turn signal lights are activated.
For details, refer to the separate owner’s manual.
Hazard warning flasher switch
N00522700262
If you press the flasher switch, the front and rear turn signals
will flash intermittently, and so will the hazard warning lights.
This is an emergency warning system and should not be used
when the vehicle is in motion, except for emergencies.
If you need to leave your vehicle, the flashers will keep work-
ing after the ignition key is removed. NOTE
If you keep the flashers on for several hours with the
engine turned off, the battery will run down.

For vehicles equipped with the Mitsubishi Multi-Commu-
nication System, Mitsubishi Multi-Communication Sys-
tem can be used to select whether the tone will sound or
not sound when the hazard warning flashers are activated.
For details, refer to the separate owner’s manual.
BK0139500US.book 85 ページ ２０１１年４月１９日　火曜日　午後１時４８分

3-92 Features and controls
3Hands-free Bluetooth
® cellular phone
interface system with voice recognition
(if so
equipped)N00506400102
The Hands-free Bluetooth
® cellular phone interface system
with voice recognition (Bluetooth
® HFP) uses a wireless com-
munication technology known as Bluetooth
® to allow you to
make hands-free calls in your vehicle using your Bluetooth
®
compatible cellular phone with Hands-free profile.
The system is equipped with a voice recognition function,
which lets you make hands-free calls by simple switch opera-
tions and voice command operations using a defined voice tree.
The Bluetooth
® HFP can be used when the ignition switch is in
the “ON” or “ACC” position.
To use the Bluetooth
® HFP, you should first connect your
Bluetooth
® compatible cellular phone to the Bluetooth
® HFP.
Refer to “Pairing a cellular phone” on page 3-100.
Bluetooth
® is a registered trademark of BLUETOOTH SIG,
INC.
NOTE
You cannot use the Bluetooth
® HFP if your cellular phone
has a dead battery or is turned off.

Hands-free calls will not be possible in areas outside your
cellular phone service area or locations where a signal
cannot reach your phone.
WA R N I N G
!
Although the Bluetooth
® HFP allows you to make
hands-free calls, if you choose to use the cellular
phone while driving, you must not allow that usage
to distract you in the safe operation of your vehicle.
Anything, including cellular phone usage, that dis-
tracts you from the safe operation of your vehicle
increases your risk of an accident. Refer to and fol-
low all state and local laws in your area regarding
cellular phone usage while driving.
BK0139500US.book 92 ページ ２０１１年４月１９日　火曜日　午後１時４８分

3-126 Features and controls
3
5. Hold down both buttons until the indicator light on
HomeLink
® flashes, changing from a “slow blink” to a
“rapidly flashing blink”. This could take up to 90 seconds.
When the indicator light flashes rapidly, both buttons may
be released. The rapidly flashing light indicates successful
programming. Press and hold Homelink
® button and
observe the indicator light.
6. If the indicator light on HomeLink
® blinks rapidly for 2
seconds and then turns solid, HomeLink
® has picked up a
“rolling code” garage door opener signal. Now continue
with the next steps to train HomeLink® to complete the
programming.
7. Press and release the “smart” or “learn” program button
located on the garage door opener’s motor to activate the
“training mode”. This button is usually located near the
antenna wire that hangs down from the motor. If the wire
originates from under a light lens, you will need to
remove the lens to access the program button.
NOTE
Once you have pressed and released the program button
on the garage door opener’s motor and the “training light”
is on, you have 30 seconds in which to perform step 8.
Use the help of a second person for convenience to assist
when performing this step.
8. Quickly within 30 seconds of pressing and releasing the
garage door opener program button, firmly press and
release HomeLink
® button you’ve just programmed.
Press and release HomeLink
® button up to three times to
complete the training.9. To program the remaining HomeLink
® buttons for addi-
tional door or gate openers, follow steps 2-8 only.
NOTE
Do not repeat step 1 unless you want to “clear” all previ-
ously programmed HomeLink
® buttons.
If you have any questions or are having difficulty programming
your HomeLink
® buttons, please refer to the HomeLink
® web
site at: www.homelink.com or call 1-800-355-3515.
Programming HomeLink
® for Canadian custom-
ers
Prior to 1992, D.O.C regulations required hand-held transmit-
ters to stop transmitting after 2 seconds. To program your
hand-held transmitter to HomeLink
®, continue to press and
hold HomeLink
® button (note steps 2 through 4 under “Pro-
gramming HomeLink
®”) while you press and re-press
(“cycle”) your hand-held transmitter every 2 seconds until the
indicator light flashes rapidly (indicating successful program-
ming).
Operating HomeLink
®
To operate, simply press the appropriate programmed
HomeLink
® button. The red indicator light will illuminate
while the signal is being transmitted.
Programming trouble diagnosisIf HomeLink
® does not quickly learn the hand-held transmitter
information:

Replace the hand-held transmitter batteries with new bat-
teries.
BK0139500US.book 126 ページ ２０１１年４月１９日　火曜日　午後１時４８分

Driving safety
4-5
4 Vehicle preparation before driving
N00629000630
For a safer and more enjoyable trip, always observe the follow-
ing: Seat belts and seats
Before starting the vehicle, make certain that you and all
passengers are seated and wearing their seat belts properly
(with children in the rear seat, in appropriate restraints),
and that all the doors are locked.

Move the driver’s seat as far backward as possible, while
still keeping good visibility, and good control of the steer-
ing wheel, brakes, accelerator, and controls. Check the
instrument panel indicators for any possible problem.

Move the front passenger seat as far back as possible.

Make sure that infants and small children are properly
restrained in accordance with all laws and regulations.Defrosters Check these by selecting the defroster mode, and set the blower
switch on high. You should be able to feel the air blowing
against the windshield.
(Refer to “Defrosting or defogging the windshield and door
windows” on page 5-12, 5-19.)
Tires Check all the tires for heavy tread wear or uneven wear pat-
terns. Look for stones, nails, glass, or other objects stuck in the
tread. Look for any tread cuts or sidewall cracks. Check the
wheel nuts for tightness, and the tires (including spare tire) for
proper pressures. Replace your tires before they are heavily
worn out.
As your vehicle is equipped with a tire pressure monitoring
system, there is a risk of damage to the tire inflation pressure
sensors when the tire is replaced on the rim. Tire replacement
should, therefore, be performed only by an authorized Mitsub-
ishi Motors dealer.Lights Have someone watch while you turn all the exterior lights on
and off. Also check the turn signal indicators and high-beam
indicators on the instrument panel. Fluid leaks Check the ground under the vehicle after parking overnight, for
fuel, water, oil, or other leaks. Make sure all the fluid levels are
correct. Also, if you can smell fuel, you need to find out why
immediately and have it fixed.
BK0139500US.book 5 ページ ２０１１年４月１９日　火曜日　午後１時４８分

4-6 Driving safety
4Safe driving techniques
N00629200052
Even this vehicle’s safety equipment, and your safest driving,
cannot guarantee that you can avoid an accident or injury.
However, if you give extra attention to the following areas, you
can better protect yourself and your passengers:

Drive defensively. Be aware of traffic, road and weather
conditions. Leave plenty of stopping distance between
your vehicle and the vehicle ahead.

Before changing lanes, check your mirrors and use your
turn-signal light.

While driving, watch the behavior of other drivers, bicy-
clists, and pedestrians.

Always obey applicable laws and regulations. Be a polite
and alert driver. Always leave room for unexpected
events, such as sudden braking.

If you plan to drive in another country, obey their vehicle
registration laws and make sure you will be able to get the
right fuel.
Driving during cold weather
N00629400272

Check the battery, including terminals and cables. During
extremely cold weather, the battery will not be as strong.
Also, the battery power level may drop because more
power is used for cold starting and driving.
Before driving the vehicle, check to see if the engine runs
at the proper speed and if the headlights are as bright as
normally. Charge or replace the battery if necessary. Dur-
ing extreme cold weather, it is possible that a very low
battery could freeze.

Warm the engine sufficiently. After starting the engine,
allow a short warm-up time to distribute oil to all cylin-
ders. Then drive your vehicle slowly.
Stay at low speeds at first so that the transaxle fluid has
time to spread to all the lubrication points.
WA R N I N G
!
The battery gives off explosive hydrogen gas. Any
spark or flame can cause the battery to explode,
which could cause serious injury or death.
Always wear protective clothes and a face mask
when working with your battery, or let a skilled
mechanic do it.
BK0139500US.book 6 ページ ２０１１年４月１９日　火曜日　午後１時４８分

Comfort controls
5-39
5
2. Turn the AUDIO switch (4) either clockwise or counter-
clockwise to adjust the sound customization features.SUB GAIN (Subwoofer tone control) To select the desired subwoofer GAIN level. BASS (Bass tone control) To select the desired bass level.
MID (Midrange tone control) To select the desired midrange level. TRE (Treble tone control) To select the desired treble level. FADE (Front/Rear balance control) To balance the volume from the F (front) and the R (rear)
speakers. BAL (Left/Right balance control) To balance the volume from the L (left) and the R (right)
speakers.FIELD (Sound field type select)To select the desired sound field.
Mode
Adjusting operation
Clockwise
Counterclockwise
SUB GAIN Increase Decrease
BASS Increase Decrease
MID Increase Decrease
TRE Increase Decrease
FA D EMore sound from
the rear speakers More sound from
the front speakers
BALMore sound from
the right speakers More sound from
the left speakers
FIELDNORMAL → STU-
DIO → CLUB →
CONCERTCONCERT →
CLUB→ STUDIO
→ NORMAL
TYPENONE → POP →
ROCK →
R+B/R&B →
COUNTRYCOUNTRY→
R+B/R&B →
ROCK → POP →
NONE
SOUND PRESET — —
Sound field type
Description
NORMALOptimized for accurate vocal and instrument
reality.
STUDIOPlaces the listener in the control room of a
recording studio with a crisp and accurate
forward placed sound stage.
CLUBPlaces the listener in the music at a dance or
jazz club with sound coming from all direc-
tions.
CONCERTUtilizing sound reflections in the Digital
Signal Processor, CONCERT gives the
impression that the listener is at concert hall
performance.
BK0139500US.book 39 ページ ２０１１年４月１９日　火曜日　午後１時４８分