2012 MITSUBISHI GALANT buttons

fog light wheel bolts clock setting check engine jump start parking brake

Page 96 of 424

MITSUBISHI GALANT 2012 9.G Owners Manual Features and controls
3-7
3
General informationYour electronic immobilizer operates on a radio frequency sub-
ject to Federal Communications Commission (FCC) Rules
(For vehicles sold in U.S.A.) and In

Page 97 of 424

MITSUBISHI GALANT 2012 9.G Owners Manual 3-8 Features and controls
3
To l o c k Press the LOCK button (1) to lock all the doors.
If they are locked while the dome light is not illuminated, the
dome light will blink once. The turn signal li

3-8 Features and controls
3
To l o c k Press the LOCK button (1) to lock all the doors.
If they are locked while the dome light is not illuminated, the
dome light will blink once. The turn signal lights will also
blink once. NOTEIf you press the LOCK button (1) after locking the doors,
the horn will sound once to confirm that they are locked.To unlock Press the UNLOCK button (2) to unlock the driver’s door only.
Press the UNLOCK button one more time to unlock all the
doors.
If the driver’s door only or all doors are unlocked while the
dome light is not illuminated, the dome light will turn on for 15
seconds. The turn signal lights will also blink twice.To open the trunk lidPress the trunk button (3) twice within 5 seconds and the trunk
lid will be opened. The trunk lid must be closed manually after
it has been opened.NOTEOn a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.Answerback function The keyless entry system answerback functions from the horn
and turn signal lights can each be turned on or off as desired.
This is done with the key removed from the ignition switch.
NOTEThe answerback function will not operate when the key is
in the ignition switch.Horn deactivation/reactivation The answerback function can be set in the following three
ways.
Each time the answerback function is set, a tone will sound to
tell you the condition of the answerback function.
1. Press the LOCK button (1) for 4 to 10 seconds and press
the UNLOCK button (2) during this time.
2. Release the LOCK and UNLOCK buttons within 10 sec-
onds of pressing the UNLOCK button in step 1.NOTEOn a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.One chime: The horn will sound if the doors are locked with
the keyless entry system.
Two chimes: The horn will not sound, even if the doors are
locked with the keyless entry system.
Three chimes: The horn will sound if the doors are already
locked and the keyless entry system is used.
In this mode, the horn will only sound when the
keyless entry LOCK button is pressed again to
reconfirm that the doors are locked.
BK0139500US.book 8 ページ２０１１年４月１９日　火曜日　午後１時４８分

Page 98 of 424

MITSUBISHI GALANT 2012 9.G Owners Manual Features and controls
3-9
3
Turn signal light deactivation/reactivation The answerback function from the turn signal lights indicating
when the doors are locked or unlocked can be turned on or off
sep

Features and controls
3-9
3
Turn signal light deactivation/reactivation The answerback function from the turn signal lights indicating
when the doors are locked or unlocked can be turned on or off
separately.
A tone will sound once when the function has been turned on,
and twice if it has been turned off.
To deactivate/reactivate the answerback function for lock-
ing of the doors, take the following steps:
1. Press the UNLOCK button (2) for 4 to 10 seconds and
press the LOCK button (1) during this time.
2. Release the LOCK button and then release the UNLOCK
button within 10 seconds of pressing the LOCK button in
step 1.
To deactivate/reactivate the answerback function for
unlocking of the doors, take the following steps:
1. Press the UNLOCK button (2) for 4 to 10 seconds and
press the LOCK button (1) during this time.
2. Release the UNLOCK button and then release the LOCK
button within 10 seconds of pressing the LOCK button in
step 1.NOTEOn a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.
Using the panic alarmIf you are near your vehicle and feel threatened, you may acti-
vate the alarm to call attention as follows:
1. Press the PANIC button (4) for more than 1 second.
2. The headlights will blink on and off and the horn will
sound intermittently for about 3 minutes.
3. To turn off the alarm, press any button on the remote con-
trol transmitter.NOTEThe indicator light (5) comes on each time a switch is
pressed.
The keyless entry system does not work if the key is in the
ignition.
The remote control transmitter can be used from about 40
feet (12 m) away. However, this distance may change if
your vehicle is near a TV transmitting tower, a power sta-
tion, or a radio station.
If the UNLOCK button (2) is pressed and no door is
opened within approximately 30 seconds: relocking will
automatically occur.
On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.
If the following conditions are observed after pressing one
of the buttons of the remote control transmitter, the battery
in the remote control transmitter may need to be replaced.
• The doors cannot be locked or unlocked.
• The trunk lid cannot be opened.
• The panic alarm cannot be operated.
• The indicator light (5) is dim or does not come on.
BK0139500US.book 9 ページ２０１１年４月１９日　火曜日　午後１時４８分

Page 99 of 424

MITSUBISHI GALANT 2012 9.G Owners Manual 3-10 Features and controls
3
If you lose your remote control transmitter, please contact
an authorized Mitsubishi Motors dealer for a replacement.
If you wish to obtain an additional remote control

Page 212 of 424

MITSUBISHI GALANT 2012 9.G Owners Manual Features and controls
3-123
3 Digital clock
(if so equipped)
N00525100209
When the ignition switch is in the “ACC” or “ON” position,
the time is displayed.How each button works:Set the time b

Page 213 of 424

MITSUBISHI GALANT 2012 9.G Owners Manual 3-124 Features and controls
3HomeLink
® Wireless Control System
(if so
equipped)N00554300030
HomeLink
® Wireless Control System is a registered trademark
of Johnson Controls Inc..
HomeLink® provi

Page 214 of 424

MITSUBISHI GALANT 2012 9.G Owners Manual Features and controls
3-125
3
Programming HomeLink
®
To program HomeLink
® to operate a garage door, gate, or
entry door opener, home or office lighting, you need to be at
the same location as the d

Page 215 of 424

MITSUBISHI GALANT 2012 9.G Owners Manual 3-126 Features and controls
3
5. Hold down both buttons until the indicator light on
HomeLink
® flashes, changing from a “slow blink” to a
“rapidly flashing blink”. This could take up to 90 s

3-126 Features and controls
3
5. Hold down both buttons until the indicator light on
HomeLink
® flashes, changing from a “slow blink” to a
“rapidly flashing blink”. This could take up to 90 seconds.
When the indicator light flashes rapidly, both buttons may
be released. The rapidly flashing light indicates successful
programming. Press and hold Homelink
® button and
observe the indicator light.
6. If the indicator light on HomeLink
® blinks rapidly for 2
seconds and then turns solid, HomeLink
® has picked up a
“rolling code” garage door opener signal. Now continue
with the next steps to train HomeLink® to complete the
programming.
7. Press and release the “smart” or “learn” program button
located on the garage door opener’s motor to activate the
“training mode”. This button is usually located near the
antenna wire that hangs down from the motor. If the wire
originates from under a light lens, you will need to
remove the lens to access the program button.
NOTEOnce you have pressed and released the program button
on the garage door opener’s motor and the “training light”
is on, you have 30 seconds in which to perform step 8.
Use the help of a second person for convenience to assist
when performing this step.
8. Quickly within 30 seconds of pressing and releasing the
garage door opener program button, firmly press and
release HomeLink
® button you’ve just programmed.
Press and release HomeLink
® button up to three times to
complete the training.9. To program the remaining HomeLink
® buttons for addi-
tional door or gate openers, follow steps 2-8 only.
NOTEDo not repeat step 1 unless you want to “clear” all previ-
ously programmed HomeLink
® buttons.
If you have any questions or are having difficulty programming
your HomeLink
® buttons, please refer to the HomeLink
® web
site at: www.homelink.com or call 1-800-355-3515.
Programming HomeLink
® for Canadian custom-
ers
Prior to 1992, D.O.C regulations required hand-held transmit-
ters to stop transmitting after 2 seconds. To program your
hand-held transmitter to HomeLink
®, continue to press and
hold HomeLink
® button (note steps 2 through 4 under “Pro-
gramming HomeLink
®”) while you press and re-press
(“cycle”) your hand-held transmitter every 2 seconds until the
indicator light flashes rapidly (indicating successful program-
ming).
Operating HomeLink
®
To operate, simply press the appropriate programmed
HomeLink
® button. The red indicator light will illuminate
while the signal is being transmitted.
Programming trouble diagnosisIf HomeLink
® does not quickly learn the hand-held transmitter
information:
Replace the hand-held transmitter batteries with new bat-
teries.
BK0139500US.book 126 ページ２０１１年４月１９日　火曜日　午後１時４８分

Load next 8 pages

Page: 1-8 9-16 17-24 25-32 32 next >

oil dipstick inflation pressure oil pressure spark plugs adblue reset four wheel drive