2012 MERCEDES-BENZ G-Class belt

For safety reasons, the rear seat bench must
only be adjusted when the vehicle is
stationary.
Never drive a vehicle with the tailgate open.
Deadly carbon monoxide (CO) gases may
enter vehicle interior resulting in
unconsciousness and death.
! Ensure that you remove all containers
from the cup holder in the rear before
folding the seat backrest and the seat
cushion of the rear bench seat forwards.
The left-hand and right-hand rear seats can
be folded down to increase the cargo
compartment capacity. The following
changes are possible:
R fold the seat backrests forward
R fold the rear bench seat back fully.
Folding the seat backrest forward :
Seat backrest release lever
; Rear bench seat release lever
i Open the rear doors. This allows you
better access to release lever :.
X Remove the center head restraint
(Y page 78).
X Pull release lever :.
The corresponding seat backrest is
released.
X Fold the seat backrest forward until it
engages. Folding the seat backrest back X
Pull release lever : and fold the seat
backrest backwards.
! Make sure that the seat belt does not
become trapped

when folding the rear seat
backrest back. Otherwise, it could be
damaged.
X Fold the seat backrest back until it engages
audibly in the seat catch.
X Install the head restraints (Y page 78).
Folding the rear bench seat forward X
Fold the backrest forwards (
Y page 191).
X Pull release lever ;.
The corresponding rear bench seat is
released.
X Fold the rear bench seat forward until it
engages.
Folding the rear bench seat into an
upright position X
Fold back the rear bench seat backrest
until it engages audibly in the seat catch.
X Fold the backrest backwards
( Y page 191).
X Install the head restraints (Y page 78). G
WARNING
Make sure that the rear bench seat and front
seat backrest are correctly engaged in
position.
If the seat backrests or rear bench seat are
not fully engaged and the following occurs:
R sharp braking
R a sudden change of direction
R an accident
the seat

backrests or rear bench seat may fold
forwards and instead of being restrained by
the seats as intended you could be injured by
them. Occupants could then also be injured
in the event of an accident, e.g. by objects Stowage areas
191
Stowing and features
Z

i
Note that regular care is essential to
ensure that
the appearance and comfort of
the covers is retained over time.
Cleaning the seat belts X
Use clean, lukewarm water and soap
solution.
! Do not

clean the seat belts using chemical
cleaning agents. Do not dry the seat belts
by warming them above 176 ‡ (80 †) or
placing them in direct sunlight. G
WARNING
Do not bleach or dye seat belts as this may
severely weaken them. In a crash, they may
not be able to provide adequate protection.
Cleaning the headliner and carpets X
Headliner: if it is very dirty, use a soft brush
or dry shampoo.
X Carpets: use the carpet and textile
cleaning agents recommended and
approved by Mercedes-Benz. 222
Care
Maintenance and care

have a code with two symbols. Retreaded
tires have a code with four symbols.
Further information about retreaded tires
(Y page 242).
Tire
size: identifier =
describes the tire size.
Tire type code: tire type code ? can be
used by the manufacturer as a code to
describe specific characteristics of the tire.
Date of manufacture: date of manufacture
A provides information about the age of a
tire. The first and second positions represent
the week of manufacture, starting with "01"
for the first calendar week. Positions three
and four represent the year of manufacture.
For example, a tire that is marked with
"3208", was manufactured in week 32 in
2008. Tire characteristics
i
Tire data is vehicle-specific and may
deviate from the data in the example.
This information describes the type of tire
cord and the number of layers in
sidewall : and under tire tread ;.Definition of terms for tires and
loading
Tire structure and characteristics
Describes the

number of layers or the number
of rubber-coated belts in the tread and the
sidewall of the tire. These are made of steel,
nylon, polyester and other materials. Bar
Metric unit for tire pressure.
14.5038 pounds per square inch (psi) and
100 kilopascals (kPa) are the equivalent of
1 bar. DOT (Department of Transportation)
DOT marked tires fulfill the requirements of
the United States Department of
Transportation. Average weight of the vehicle
occupants
The number of occupants for which the
vehicle is

designed multiplied by 68 kilograms
(150 lb). Uniform Tire Quality Grading
Standards
A uniform standard to grade the quality of
tires with

regards to tread quality, tire traction
and temperature characteristics. The quality
grading assessment is made by the
manufacturer following specifications from
the U.S. government. The quality grade of a
tire is imprinted on the sidewall of the tire. Recommended tire pressure
The recommended tire pressure for your
vehicle under normal driving conditions. You
will find

the recommendation on the Tire and
Loading Information placard on the B-pillar on
the driver's side of your vehicle. The
recommended tire pressure provides the best
balance between handling characteristics,
ride comfort and wear. Additional information
on particular driving conditions is located on
the tire pressure table on the inside of the fuel
filler flap. 262
Definition of terms for tires and loading
Wheels and tires