2012 MAZDA MODEL 5 headlight bulb

Black plate (177,1)
NOTElThe headlights, other exterior lights and dashboard illumination may not turn off immediately
even if the surrounding area becomes well-lit because the light sensor determines that it is
nighttime if the surrounding area is continuously dark for several minutes such as inside long
tunnels, traffic jams inside tunnels, or in indoor parking lots.
In this case, the light turns off if the light switch is turned to the OFF position.
lThe dashboard illumination can be adjusted by rotating the knob in the instrument cluster. Also,
the day/night mode can be changed by pressing the knob. To adjust the brightness of the
dashboard illumination: Refer to Dashboard Illumination on page 5-35.
lWhen the headlight switch is in the AUTO position and the ignition is switched to ACC or the
ignition is switched off, the headlights, other exterior lights and dashboard illumination will turn
off.
lThe sensitivity of the AUTO lights may be changed by an Authorized Mazda Dealer. Refer to
Personalization Features on page 10-8.
Xenon fusion headlight bulbsí
The low-beam bulbs of the headlights have xenon fusion bulbs that produce a bright white
beam over a wide area.
WARNING
Do not replace the xenon fusion bulbs yourselfReplacing the xenon fusion bulbs yourself is dangerous. Because the xenon fusion
bulbs require high voltage, you could receive an electric shock if the bulbs are
handled incorrectly. Consult an Authorized Mazda Dealer when the replacement is
necessary.
NOTE
If the headlights flicker, or the brightness weakens, the bulb-life may be depleted and a replacement is
necessary. Consult an Authorized Mazda Dealer.
Driving Your Mazda
Switches and Controls
5-53íSome models.
Mazda5_8BR9-EA-10J_Edition3 Page177
Monday, February 21 2011 1:44 PM
Form No.8BR9-EA-10J

Black plate (179,1)
Select the proper headlight angle from the following
chart.Front seat Rear
seat
*1Load Switch
Position
Driver Passenger
× ――― 0
×× ――0
×× × ―1
×× ×× 2
× ―― ×3
×: Yes
― :No
*1 Second-row and third-row seats
qDaytime Running Lights (Canada)
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition is
switched ON.
NOTE
The Daytime Running Lights turn off when the
parking brake is applied.
Turn and Lane-Change
Signals
Turn Signals
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to
its original position.
Right turn
Left turn
Right lane change
Left lane change OFF
Green indicators on the dashboard show
which signal is working.
Lane-change signals
Move the lever slightly toward the
direction of the change
―until the
indicator flashes ―and hold it there. It
will return to the off position when
released.
NOTE
lIf an indicator light stays on without
flashing or if it flashes abnormally, one of
the turn signal bulbs may be burned out.
lA personalized function is available to
change the turn indicator sound volume.
Refer to Personalization Features on page
10-8.
Driving Your Mazda
Switches and Controls
5-55
Mazda5_8BR9-EA-10J_Edition3 Page179
Monday, February 21 2011 1:44 PM
Form No.8BR9-EA-10J

Black plate (358,1)
Light Bulbs
Headlights (Low beam)Headlights (High beam)
High-mount brake light Fog lights
Front turn signal lights/Front side-marker
lights/Parking lights
Some models.
License plate lights Brake lights/Taillights/Rear side-
marker lights
Overhead light/Map lights (Front)
Overhead light (Rear)
Luggage compartment light
Rear turn signal lights Reverse lights
8-40
Maintenance and Care
Owner Maintenance
Mazda5_8BR9-EA-10J_Edition3 Page358
Monday, February 21 2011 1:45 PM
Form No.8BR9-EA-10J

Black plate (359,1)
WARNING
Do not replace the xenon fusion bulbs
yourself:Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement
is necessary.
Never touch the glass portion of a
halogen bulb with your bare hands and
always wear eye protection when
handling or working around the bulbs: When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when
lit.
Always keep halogen bulbs out of the
reach of children: Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb
or breaking it some other way.
qReplacing Exterior Light Bulbs
Headlight bulbs
High-beam bulbs
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood. 3. Remove the hood wire from the guide.
Guide
Wire
4. Disconnect the electrical connector
from the bulb by pressing the tab on
the connector with your finger and
pulling the connector.
Maintenance and Care
Owner Maintenance
8-41
Mazda5_8BR9-EA-10J_Edition3 Page359
Monday, February 21 2011 1:45 PM
Form No.8BR9-EA-10J

Black plate (360,1)
5. Turn the bulb assemblycounterclockwise and remove it.
Carefully remove the bulb from its
socket in the reflector by gently pulling
it straight backward out of the socket.
6. Install the new bulb in the reverse order
of removal.
Low-beam bulbs
(Xenon fusion bulb)
You cannot replace the low beam bulbs by
yourself. The bulbs must be replaced at an
Authorized Mazda Dealer.
(Halogen bulb)
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Lift the hood. 3. Disconnect the electrical connector
from the bulb by pressing the tab on
the connector with your finger and
pulling the connector.
4. Turn the bulb assemblycounterclockwise and remove it.
Carefully remove the bulb from its
socket in the reflector by gently pulling
it straight backward out of the socket.
5. Install the new bulb in the reverse order
of removal.
Fog light bulbsí
1. Make sure the ignition is switched off,and the headlight switch is off.
8-42
Maintenance and Care
íSome models.
Owner Maintenance
Mazda5_8BR9-EA-10J_Edition3 Page360
Monday, February 21 2011 1:45 PM
Form No.8BR9-EA-10J

Black plate (361,1)
2. Turn the screw counterclockwise andremove it, then partially peel back the
mudguard.
3. Disconnect the electrical connectorfrom the bulb by pressing the tab on
the connector with your finger and
pulling the connector.
4. Turn the bulb assemblycounterclockwise and remove it.
Carefully remove the bulb from its
socket in the reflector by gently pulling
it straight backward out of the socket.
5. Install the new bulb in the reverse order
of removal.
Front turn signal lights/Front side-
marker lights/Parking lights
1. Make sure the ignition is switched off,and the headlight switch is off.
2. Lift the hood.
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Remove the bulb by pressing it in slightly and turning it
counterclockwise.
Maintenance and Care
Owner Maintenance
8-43
Mazda5_8BR9-EA-10J_Edition3 Page361
Monday, February 21 2011 1:45 PM
Form No.8BR9-EA-10J

Black plate (362,1)
5. Install the new bulb in the reverse orderof removal.
Brake lights/Taillights/Rear side-
marker lights, Rear turn signal lights
1. Make sure the ignition is switched off,and the headlight switch is off.
2. Turn the bolts counterclockwise and remove them.
3. Pull the upper part of the cover around
the clip outward to detach the clip.
Clip
4. Pull the unit rearward to remove it.
5. Turn the socket and bulb assemblycounterclockwise and remove it.
6. Disconnect the bulb from the socket.
Brake lights/Taillights/Rear side-
marker lights
8-44
Maintenance and Care
Owner Maintenance
Mazda5_8BR9-EA-10J_Edition3 Page362
Monday, February 21 2011 1:45 PM
Form No.8BR9-EA-10J

Black plate (363,1)
Rear turn signal lights
7. Install the new bulb in the reverse orderof removal.
NOTE
To install the unit, insert the hooks (2
locations) on the unit side into the clips on the
vehicle side, and install the unit.
Clip
Hook
Reverse lights
1. Make sure the ignition is switched off, and the headlight switch is off. 2. Remove the cover with a cloth-
wrapped flathead screwdriver to the
cover.
3. Turn the socket and bulb assemblycounterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
High-mount brake light
Due to the complexity and difficulty of
the procedure, the LED bulbs must be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible because
it is built into the unit. Replace the unit.
Maintenance and Care
Owner Maintenance
8-45
Mazda5_8BR9-EA-10J_Edition3 Page363
Monday, February 21 2011 1:45 PM
Form No.8BR9-EA-10J