2012 Lexus IS220d mirror

67
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
IS250/220d/200d_EE
Your preferred driving position (the position of the driver's seat, steer-
ing wheel and outside rear view mirrors) can be memorized and
recalled with the touch of a button. It is also possible to set this func-
tion to activate automatically when the doors are unlocked.
Three different driving positions can be entered into memory.
Entering a position to memory
Switch to IGNITION ON mode.
Adjust the driver’s seat, steering wheel, and outside rear
view mirrors to the desired positions.
Push the “SET” button, then
within 3 seconds push button
“1”, “2” or “3” until the sig-
nal beeps.
If the selected button has
already been preset, the pre-
viously recorded position
will be overwritten.
Recalling the memorized position
Vehicles with an automatic transmission: Check that the shift
lever is set in P.
Vehicles with a manual transmission: Check that the parking
brake is set.
Switch to IGNITION ON mode.
Push button “1”, “2” or “3”
to recall the memorized posi-
tion.
STEP1
STEP2
STEP3
STEP1
STEP2
: If equipped

68
1-3. Adjustable components (seats, mirrors, steering wheel)
IS250/220d/200d_EE
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before per-
forming the following.
Carry only the key (including the card key
) to which you want to
link the driving position. If 2 or more keys are in the vehicle, the
driving position cannot be linked properly.

: If equipped
Using the wireless remote control
Turn the “ENGINE START STOP” switch OFF and close
the driver's door.
Press and hold the desired but-
ton (“1”, “2” or “3”) while
pressing on the wireless
remote control until the signal
beeps.
The driving position is recalled
when the driver's door is
unlocked using the entry func-
tion or wireless remote control
and the driver's door is opened.
To prevent unintended triggering of the alarm, open and close a
door once after a driving position has been recorded. (If a door is
not opened within 30 seconds after is pressed, the doors will be
locked again and the alarm will automatically be set.)
In case that the alarm is triggered, immediately stop the alarm.
(P. 102)
STEP1
STEP2

69
1
1-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
IS250/220d/200d_EEUsing the door lock switch
Turn the “ENGINE START STOP” switch OFF and close
the driver's door.
While pressing the desired but-
ton (“1”, “2” or “3”), press the
lock or unlock side on the
driver’s door lock switch until
the signal beeps.
The driving position is recalled
when the driver's door is
unlocked using the entry func-
tion or wireless remote control
and the driver's door is opened.
STEP1
STEP2

70
1-3. Adjustable components (seats, mirrors, steering wheel)
IS250/220d/200d_EE
Canceling the linked door unlock operation
Turn the “ENGINE START STOP” switch OFF and close the
driver's door.
Using the wireless remote control: While pushing the “SET” but-
ton, press on the wireless remote control until the signal
beeps.
Using the door lock switch: While pressing the “SET” button, press
the lock or unlock side on the door lock switch until the signal
beeps.
Operating the driving position memory after turning the “ENGINE START
STOP” switch OFF
Memorized positions (except for the steering wheel position) can be acti-
vated up to 180 seconds after the driver’s door is opened and another 60 sec-
onds after it is closed again, even after turning the “ENGINE START
STOP” switch OFF.
To cancel seat position recall
Perform any of the following operations.
Push the “SET” button.
Push button “1”, “2” or “3”.
Adjust the seat using the switches (only cancels seat position recall).
If the battery is disconnected
The memorized positions are erased when the battery is disconnected.
CAUTION
Seat adjustment caution
Take care during seat adjustment that the seat does not strike the rear pas-
senger or squeeze your body against the steering wheel.
STEP1
STEP2

71
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
IS250/220d/200d_EE
Head restraints
Removing the head restraints (front seats)
Vertical adjustment
Up
Pull the head restraints up.
Down
Front and center rear seats:
Push the head restraint down
while pushing the lock
release button.
Folding operation (outside
rear seats only)
To stow the head restraint by
folding it forward, pull the
head restraint up while push-
ing the lock release button.
Only the button on the right
stay (when facing the front of
the vehicle) can be used to
fold the head restraint for-
Lock release but-
Lock release but-
Pull the head restraint up while pushing
the lock release button.

72
1-3. Adjustable components (seats, mirrors, steering wheel)
IS250/220d/200d_EE
Removing the head restraint (center rear seat)
Removing the head restraints (outside rear seats)
Adjusting the height of the head restraints
When using the rear seat head restraints
Center rear seat: Always raise the head restraint one level from the stowed
position when using.
Outside rear seats: Make sure the head restraints are not in the stowed/
folded position while in use.
Pull the head restraint up while pushing
the lock release button.
Lock release but-
Pull the head restraint up while pushing
both of the lock release buttons.
Lock release but-
Make sure that the head restraints are
adjusted so that the center of the head
restraint is closest to the top of your ears.

73
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
IS250/220d/200d_EE
CAUTION
Head restraint precautions
Observe the following precautions regarding the head restraints. Failure to
do so may result in death or serious injury.
Use the head restraints designed for each respective seat.
Adjust the head restraints to the correct position at all times.
After adjusting the head restraints, push down on them and make sure
they are locked in position.
Do not drive with the head restraints removed.

74
1-3. Adjustable components (seats, mirrors, steering wheel)
IS250/220d/200d_EE
Seat belts
Make sure that all occupants are wearing their seat belts before driving
the vehicle.
Correct use of the seat belts
Extend the shoulder belt so
that it comes fully over the
shoulder, but does not
come into contact with the
neck or slide off the shoul-
der.
Position the lap belt as low
as possible over the hips.
Adjust the position of the
seatback. Sit up straight
and well back in the seat.
Do not twist the seat belt.
Fastening and releasing the seat belt
Fastening the belt
Push the tab into the buckle
until a clicking sound is
heard.
Releasing the belt
Press the release button.