2012 Lexus GS350 lights

715 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)
15LH-IG210
Multiport fuel injection system/sequen-
tial multiport fuel injection system, stop
lights, smart entry & start system, steer-
ing lock system
16LH J/B-B7.5Body ECU
17S/ROOF20Moon roof
18P/SEAT2 F/L25Power seats
19A/C7.5Air conditioning system
FuseAmpereCircuit

7186-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)
Right-hand drive vehicles
FuseAmpereCircuit
1STOP7.5Stop lights, high mounted stoplight
2P/SEAT1 F/R30Power seats
3FR P/OUTLET15Power outlet (front)
4P/W-B5Power window master switch
5RR P/OUTLET15Power outlet (rear)
6P/SEAT2 F/R25Power seats
7AV S20AV S
8WIPER30Windshield wipers
9WA S H20Windshield washer
10RH ECU-IG10
Navigation system, VDIM, D-SW
MODULE (Blind Spot Monitor, heated
steering wheel)
11RH-IG10
Tension reducer, AWD system, power
seats, head-up display, front right-hand
door ECU, nanoe, shift lock system,
electric tilt and telescopic steering col-
umn, seat heater/ventilator switches,
smart entry & start system antennas, tire
pressure warning system receiver, driver
monitor system
12DOOR FR30
Front right-hand door control system
(outside rear view mirror defoggers,
power window)

721 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)
After a fuse is replaced
If the lights do not turn on even after the fuse has been replaced, a bulb may
need replacement. (P. 722)
If the replaced fuse blows again, have the vehicle inspected by any autho-
rized Lexus dealer or repairer, or another duly qualified and equipped pro-
fessional.
If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
When replacing light bulbs
Lexus recommends that you use genuine Lexus products designed for this
vehicle. Because certain bulbs are connected to circuits designed to prevent
overload, non-genuine parts or parts not designed for this vehicle may be
unusable.
CAUTION
To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage, and possibly a fire or injury.
Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
Always use a genuine Lexus fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
This can cause extensive damage or even fire.
Do not modify the fuses or fuse boxes.
NOTICE
Before replacing fuses
Have the cause of electrical overload determined and repaired by any
authorized Lexus dealer or repairer, or another duly qualified and equipped
professional as soon as possible.

7246-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)
Front fog lights (if equipped)
To allow enough working
space, turn the steering
wheel to the opposite side
of the bulb to be replaced.
Remove the 2 fender liner
clips.
Turn the steering wheel to the
left when replacing the right
side light bulb, and turn the
steering wheel to the right when
replacing the left side light bulb.
To take out the clips, turn the
head of the clip to unlock, then
remove by pulling.
While holding the clamp
open, pull and remove the
tabs and open the fender
liner.
Unplug the connector while
pressing the lock release.
Replacing light bulbs
1
2
3

725 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)Turn the bulb base counter-
clockwise.
Set the new light bulb.
Align the 3 tabs on the light
bulb with the mounting, and
insert. Turn it clockwise to set.
Set the connector.
After installing the connector,
shake the bulb base gently to
check that it is not loose, turn
the fog lights on once and visu-
ally confirm that no light is
leaking through the mounting.
Reinstall the fender liner
and install the clips.
Insert the clips and turn to lock.
4
5
6
7

7266-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)
Front turn signal lights
For the left side only: To
allow enough working
space, turn the steering
wheel all the way to the
right, then remove the bolts
and take off the cover.
Turn the bulb base counterclockwise.
1
2
Right sideLeft side

7286-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)
Rear turn signal lights
Open the trunk lid and
remove the cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
When installing, reverse the
steps listed.
After installing the bulb base,
secure the cord with the clips
and install the cover in its origi-
nal position.
1
2
3
4

731 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)
Outer foot lights
Press the upper part of the
outside rear view mirror to
tilt the mirror face upward,
and apply protective tape to
the lower part of the mirror
cover.
Insert 2 flathead screw-
drivers wrapped in protec-
tive tape, and disconnect the
tabs behind the mirror.
Prize the mirror out toward you,
disconnecting the tabs 2 at a
time.
Work carefully, ensuring that
you do not drop the mirror.
Disconnect the connectors
behind the mirror, and
remove the mirror.
When removing the thin con-
nectors, make sure to mark one
of the connectors with a piece of
tape, to avoid mixing them up
when reinstalling.
Work carefully, ensuring that
you do not drop the mirror.
When handling the mirror, do
not touch the parts applied with
grease.
The number of connectors
equipped differs by vehicle
specification.
1
2
3