2012 Lexus CT200h ECU

542
4-3. Do-it-yourself maintenance
CT200h_OM_OM76067E_(EE)
5WIP30 AWindshield wipers
6RR WIP20 ARear window wiper and washer
7WASHER15 AWindshield washer
8A/C10 AAir conditioning system
9GAUGE10 A
Windshield wiper de-icer switch,
automatic headlight leveling sys-
tem
10ECU-IG NO.210 A
Windshield wipers, Lexus parking
assist monitor, Lexus parking
assist-sensor, electronically con-
trolled brake system, navigation
system, electric power steering
system, turn signal lights, emer-
gency flashers, yaw rate and G
sensor, headlight cleaner, outside
rear view mirrors, driving mode
select switch, overhead module,
pre-crash seat belts, seat heater
switches, heated steering wheel
switch, dynamic radar cruise con-
trol
11ECU-IG NO.110 ANo circuit
12S/ROOF30 AMoon roof
FuseAmpereCircuit

544
4-3. Do-it-yourself maintenance
CT200h_OM_OM76067E_(EE)
30RAD NO.27.5 A
Audio system, Lexus parking
assist monitor, navigation system,
overhead module
31PWR OUTLET15 APower outlet
32ECU-ACC10 AAir conditioning system, outside
rear view mirror switches
33PWR OUTLET215 ANo circuit
After a fuse is replaced
If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. (P. 546)
If the replaced fuse blows again, have the vehicle inspected by any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
When replacing light bulbs
Lexus recommends that you use genuine Lexus products designed for this
vehicle. Because certain bulbs are connected to circuits designed to prevent
overload, non-genuine parts or parts not designed for this vehicle may be
unusable.
FuseAmpereCircuit

548
4-3. Do-it-yourself maintenance
CT200h_OM_OM76067E_(EE)
Replacing light bulbs
Headlight low beams (halogen headlights)
For the right side only: Remove
the securing clips and unclip
the engine coolant reservoir
hose. Then lift up the air
cleaner inlet duct.
Unplug the connector while
pressing the lock release.
STEP1
STEP2

550
4-3. Do-it-yourself maintenance
CT200h_OM_OM76067E_(EE)Headlight high beams (LED headlights)
For the right side only: Remove the securing clips and
unclip the engine coolant reservoir hose. Then lift up the air
cleaner inlet duct. (P. 548)
Turn the cover counterclock-
wise and remove it.
Turn the bulb base counter-
clockwise.
Unplug the connector while
pulling the lock release.
STEP1
STEP2
STEP3
STEP4

552
4-3. Do-it-yourself maintenance
CT200h_OM_OM76067E_(EE)Front turn signal lights (halogen headlights)
For the right side only: Remove the securing clips and
unclip the engine coolant reservoir hose. Then lift up the air
cleaner inlet duct. (P. 548)
Turn the bulb base counter-
clockwise.
Remove the light bulb.
STEP1
STEP2
STEP3

559
4-3. Do-it-yourself maintenance
4
Maintenance and care
CT200h_OM_OM76067E_(EE)
LED lights
The headlight low beams (LED type), front position lights, daytime running
lights, side turn signal lights, stop/tail lights and high mounted stoplight
consist of a number of LEDs. If any of the LEDs burn out, take your vehicle
to any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional to have the light replaced.
Condensation build-up on the inside of the lens
Contact any authorized Lexus dealer or repairer, or another duly qualified
and equipped professional for more information in the following situations.
Temporary condensation build-up on the inside of the headlight lens does
not indicate a malfunction.
Large drops of water have built up on the inside of the lens.
Water has built up inside the headlight.
When replacing light bulbs
P. 5 4 4
CAUTION
Replacing light bulbs
Turn off the lights. Do not attempt to replace the bulb immediately after
turning off the lights.
The bulbs become very hot and may cause burns.
Do not touch the glass portion of the light bulb with bare hands. Hold the
bulb by the plastic or metal portion.
If the bulb is scratched or dropped, it may blow out or crack.
Fully install light bulbs and any parts used to secure them. Failure to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
To prevent damage or fire
Make sure bulbs are fully seated and locked.

564
5-1. Essential information
CT200h_OM_OM76067E_(EE)
Emergency towing
If a tow truck is not available in
an emergency, your vehicle
may be temporarily towed
using a cable or chain secured
to the emergency towing eye-
let(s). This should only be
attempted on hard surfaced
roads for short distances at
under 30 km/h (18 mph).
A driver must be in the vehicle
to steer and operate the brakes.
The vehicle’s wheels, drive
train, axles, steering and brakes
must be in good condition.

5
565
5-1. Essential information
When trouble arises
CT200h_OM_OM76067E_(EE)
Installing towing eyelets
Remove the eyelet cover using
a flathead screwdriver.
To protect the bodywork, place
a rag between the screwdriver
and the vehicle body as shown
in the illustration.
Insert the towing eyelet into the
hole and tighten partially by
hand.
Tighten down the towing eyelet
securely using a wheel nut
wrench.
STEP1
STEP2
STEP3