2012 Lexus CT200h Change

197
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
NOTICE
When encountering flooded roads
Do not drive on a road that has flooded after heavy rain etc. Doing so may
cause the following serious damage to the vehicle:
Engine stalling
Short in electrical components
Engine damage caused by water immersion
In the event that you drive on a flooded road and the vehicle is flooded, be
sure to have any authorized Lexus dealer or repairer, or another duly quali-
fied and equipped professional check the following:
Brake function
Changes in quantity and quality of engine oil, transmission fluid for the
hybrid system etc.
Lubricant condition for the bearings and suspension joints (where possi-
ble), and the function of all joints, bearings, etc.
If the P position control system is damaged by flooding, it may not be possi-
ble to shift the shift position to P, or from P to other positions. When the
shift position cannot be changed from P to any other position, the front
wheels will lock, and you will be unable to tow the vehicle with the front
wheels on the ground, as the front wheels may be locked. In this case, trans-
port the vehicle with both front wheels or all four wheels lifted.

198
2-1. Driving procedures
CT200h_OM_OM76067E_(EE)
Power (ignition) switch
Performing the following operations when carrying the electronic key
on your person starts the hybrid system or changes “POWER” switch
modes.
Starting the hybrid system
Check that the parking brake is set.
Firmly depress the brake pedal.
Check that the “POWER” switch indicator turns green. If the
indicator does not turn green, the hybrid system cannot be
started.
When the shift position is N, the hybrid system cannot start.
Shift the shift position to P when starting the hybrid system.
(P. 210)
Press the “POWER” switch.
Continue depressing the
brake pedal until the hybrid
system is completely started.
The hybrid system can be
started from any “POWER”
switch mode.
STEP1
STEP2
STEP3

199
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
Check that the “READY” indicator is on.
If the “READY” indicator changes from a flashing light to a
solid light and the buzzer sounds, the hybrid system is starting
normally.
The vehicle will not move when the “READY” indicator is
off.
The vehicle can move when the “READY” indicator is on
even if the engine is stopped. (The gasoline engine starts or
stops automatically in accordance with the state of the vehi-
cle.)
Stopping the hybrid system
Stop the vehicle completely.
Set the parking brake. (P. 217)
Shift the shift position to P. (P. 2 1 0 )
Check that the shift position indicator shows P. (P. 207)
Press the “POWER” switch.
The hybrid system will stop, and the meter display will be
extinguished (the shift position indicator will be extinguished
a few seconds after the meter display)
STEP4
STEP1
STEP2
STEP3
STEP4

200
2-1. Driving procedures
CT200h_OM_OM76067E_(EE)
Auto power off function
If the vehicle is left in ACCESSORY mode for more than 20 minutes or ON
mode (the hybrid system is not operating) for more than an hour with the
shift position in P, the “POWER” switch will automatically turn off. How-
ever, this function cannot entirely prevent the 12-volt battery from discharg-
ing. Do not leave the vehicle with the “POWER” switch in ACCESSORY or
ON mode for long periods of time when the hybrid system is not operating.
Sounds and vibrations specific to a hybrid vehicle
P. 4 2
Changing “POWER” switch modes
Modes can be changed by pressing the “POWER” switch with
the brake pedal released. (The mode changes each time the
switch is pressed.)
Off
The emergency flashers can
be used.
ACCESSORY mode
Some electrical components
such as the audio system can
be used.
The “POWER” switch indi-
cator turns amber.
ON mode
All electrical components can
be used.
The “POWER” switch indi-
cator turns amber.

202
2-1. Driving procedures
CT200h_OM_OM76067E_(EE)
If the “READY” indicator does not come on
If the “READY” indicator does not come on when you press the “POWER”
switch with the shift position in P and the brake pedal depressed, contact
any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional immediately.
If the hybrid system is malfunctioning
P. 5 7 3
If the electronic key battery is depleted
P. 5 2 7
Operation of the “POWER” switch
When operating the “POWER” switch, one short, firm press is enough.
If the switch is pressed improperly, the hybrid system may not start or
the “POWER” switch mode may not change. It is not necessary to press
and hold the switch.
If attempting to restart the hybrid system immediately after turning the
“POWER” switch off, the hybrid system may not start in some cases.
After turning the “POWER” switch off, please wait a few seconds before
restarting the hybrid system.
Automatically P position selection function
P. 2 1 3
When the P position control system malfunctions
The “POWER” switch will not be able to be turned off. In such a case, the
switch can be turned off after applying the parking brake.
Have the vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional immediately.

207
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
Hybrid transmission
Select a shift position appropriate for the driving conditions.
Shifting the shift lever
Shift lever
Operate the shift lever gently and ensure correct shifting operation.
When shifting to the D or R positions, move the shift lever
along the shift gate.
To shift to the N position, slide the shift lever to the left
(left-hand drive vehicle) or right (right-hand drive vehicle)
and hold it. The shift position will change to N.
Shifting to B is only possible when shift position D is
selected.
The shift lever will always return to this original position
after a shifting operation.
When shifting from P to N, D or R, from D to R, or from R to D,
ensure that the brake pedal is being depressed and the vehicle is sta

208
2-1. Driving procedures
CT200h_OM_OM76067E_(EE)
Shift position indicator
The current shift position is illuminated.
When any shift position other than D or B is selected, the arrow
toward B and B position indicator disappear from the shift position
indicator.
When selecting the shift position, make sure that the shift position has
been changed to the desired position by checking the shift position
indicator provided on the instrument cluster.
Shift position purpose
*: For good fuel economy and noise reduction, the D position should
ll b d
Shift positionFunction
PParking the vehicle/starting the hybrid system
RReversing
NNeutral
DNormal driving*
B
Applying engine braking or strong braking when
the accelerator pedal has been released on steep
downward slopes etc.

209
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
Selecting a driving mode
The following modes can be selected to suit driving condi-
tions:
Normal mode
Eco drive mode
Suitable for improving the
fuel economy, because the
torque corresponding to the
accelerator pedal depression
amount can be generated
more smoothly than it is in
normal conditions and the
operation of the air condi-
tioning system (heating/cool-
ing) will be minimized.
When the driving mode
select switch is turned left,
the “ECO MODE” indicator
comes on in the instrument
cluster.
Press the switch to change
the driving mode to normal
mode.
Sport mode
Use when high levels of
response and feeling are
desirable, such as when driv-
ing in mountainous regions
or when overtaking.
When the driving mode
select switch is turned right,
the “SPORT MODE” indica-
tor comes on in the instru-
ment cluster