2012 Lexus CT200h parking brake

187
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
Starting off on a uphill
Firmly set the parking brake with the brake pedal
depressed, and then shift the shift position to D.
Release the brake pedal and gently depress the accelerator
pedal.
Release the parking brake.
When starting off on a uphill
The hill-start assist control is available. (P. 296)
Driving in the rain
Drive carefully when it is raining, because visibility will be reduced, the
windows may become fogged-up, and the road will be slippery.
Drive carefully when it starts to rain, because the road surface will be
especially slippery.
Refrain from high speeds when driving on an expressway in the rain,
because there may be a layer of water between the tires and the road sur-
face, preventing the steering and brakes from operating properly.
STEP1
STEP2
STEP3

192
2-1. Driving procedures
CT200h_OM_OM76067E_(EE)
CAUTION
If you hear a squealing or scraping noise (brake pad wear indicators)
Have any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional check and replace the brake pads as soon as possible.
Rotor damage may result if the pads are not replaced when needed.
It is dangerous to drive the vehicle when the wear limits of the brake pads
and/or those of the brake discs are exceeded.
When the vehicle is stopped
Do not depress the accelerator pedal unnecessarily.
If the vehicle is in any shift position other than P or N, the vehicle may
accelerate suddenly and unexpectedly, causing an accident.
Do not leave the vehicle with the hybrid system on for a long time.
If such a situation cannot be avoided, park the vehicle in an open space
and check that exhaust fumes do not enter the vehicle interior.
In order to prevent accidents due to the vehicle rolling away, always keep
depressing the brake pedal while the “READY” indicator is on. Apply the
parking brake as necessary.
If the vehicle is stopped on an incline, in order to prevent accidents caused
by the vehicle rolling forward or backward, always depress the brake
pedal and securely apply the parking brake as needed.
Avoid revving or racing the engine.
Running the engine at high speed while the vehicle is stopped may cause
the exhaust system to overheat, which could result in a fire if combustible
material is nearby.

193
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
CAUTION
When the vehicle is parked
Make sure to firmly apply the parking brake and shift the shift position to
P.
Failure to do so may cause the vehicle to move, or the vehicle to acceler-
ate suddenly if the accelerator pedal is accidentally depressed. Also, when
leaving the vehicle, make sure to turn off the hybrid system and lock the
vehicle.
Sound or shuddering may not be noticed even when the hybrid vehicle is
ready to drive (when the “READY” indicator is illuminated).
Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in
the vehicle when it is in the sun.
Doing so may result in the following:
• Gas may leak from a cigarette lighter or spray can, and may lead to a
fire.
• The temperature inside the vehicle may cause the plastic lenses and
plastic material of glasses to deform or crack.
• Soft drink cans may fracture, causing the contents to spray over the
interior of the vehicle, and may also cause a short circuit in the vehi-
cle’s electrical components.
Do not leave cigarette lighters in the vehicle. If a cigarette lighter is in a
place such as the glove box or on the floor, it may be lit accidentally when
luggage is loaded or the seat is adjusted, causing a fire.
Do not attach adhesive discs to the windshield or windows. Do not place
containers such as air fresheners on the instrument panel or dashboard.
Adhesive discs or containers may act as lenses, causing a fire in the vehi-
cle.
Do not leave a door or window open if the curved glass is coated with a
metallized film such as a silver-colored one. Reflected sunlight may cause
the glass to act as a lens, causing a fire.

195
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
CAUTION
When taking a nap in the vehicle
Always turn the hybrid system off. Otherwise, if you accidentally move the
shift lever or depress the accelerator pedal, this could cause an accident or
fire due to hybrid system overheating. Additionally, if the vehicle is parked
in a poorly ventilated area, exhaust gases may collect and enter the vehicle,
leading to death or a serious health hazard.
When braking
When the brakes are wet, drive more cautiously.
Braking distance increases when the brakes are wet, and this may cause
one side of the vehicle to brake differently than the other side. Also, the
parking brake may not securely hold the vehicle.
If the electronically controlled assist function does not operate, do not fol-
low other vehicles closely and avoid downhill or sharp turns that require
braking.
In this case, braking is still possible, but the brake pedal should be
depressed more firmly than usual. Also, the braking distance will
increase.
The brake system consists of 2 individual hydraulic systems; if one of the
systems fails, the others will still operate. In this case, the brake pedal
should be depressed more firmly than usual and the braking distance will
increase. If this happens, do not continue to drive the vehicle. If the brake
system warning light (red indicator) comes on together with the buzzer
sound while driving, immediately stop the vehicle in a safe place and con-
tact any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.

198
2-1. Driving procedures
CT200h_OM_OM76067E_(EE)
Power (ignition) switch
Performing the following operations when carrying the electronic key
on your person starts the hybrid system or changes “POWER” switch
modes.
Starting the hybrid system
Check that the parking brake is set.
Firmly depress the brake pedal.
Check that the “POWER” switch indicator turns green. If the
indicator does not turn green, the hybrid system cannot be
started.
When the shift position is N, the hybrid system cannot start.
Shift the shift position to P when starting the hybrid system.
(P. 210)
Press the “POWER” switch.
Continue depressing the
brake pedal until the hybrid
system is completely started.
The hybrid system can be
started from any “POWER”
switch mode.
STEP1
STEP2
STEP3

199
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
Check that the “READY” indicator is on.
If the “READY” indicator changes from a flashing light to a
solid light and the buzzer sounds, the hybrid system is starting
normally.
The vehicle will not move when the “READY” indicator is
off.
The vehicle can move when the “READY” indicator is on
even if the engine is stopped. (The gasoline engine starts or
stops automatically in accordance with the state of the vehi-
cle.)
Stopping the hybrid system
Stop the vehicle completely.
Set the parking brake. (P. 217)
Shift the shift position to P. (P. 2 1 0 )
Check that the shift position indicator shows P. (P. 207)
Press the “POWER” switch.
The hybrid system will stop, and the meter display will be
extinguished (the shift position indicator will be extinguished
a few seconds after the meter display)
STEP4
STEP1
STEP2
STEP3
STEP4

202
2-1. Driving procedures
CT200h_OM_OM76067E_(EE)
If the “READY” indicator does not come on
If the “READY” indicator does not come on when you press the “POWER”
switch with the shift position in P and the brake pedal depressed, contact
any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional immediately.
If the hybrid system is malfunctioning
P. 5 7 3
If the electronic key battery is depleted
P. 5 2 7
Operation of the “POWER” switch
When operating the “POWER” switch, one short, firm press is enough.
If the switch is pressed improperly, the hybrid system may not start or
the “POWER” switch mode may not change. It is not necessary to press
and hold the switch.
If attempting to restart the hybrid system immediately after turning the
“POWER” switch off, the hybrid system may not start in some cases.
After turning the “POWER” switch off, please wait a few seconds before
restarting the hybrid system.
Automatically P position selection function
P. 2 1 3
When the P position control system malfunctions
The “POWER” switch will not be able to be turned off. In such a case, the
switch can be turned off after applying the parking brake.
Have the vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional immediately.

210
2-1. Driving procedures
CT200h_OM_OM76067E_(EE)
P position switch
When shifting the shift position to P
Fully stop the vehicle and set
the parking brake, and then
press the P position switch.
When the shift position is
changed to P, the switch indica-
tor comes on.
Check that the P position is illu-
minated on the shift position
indicator.
Shifting the shift position from P to other positions
While depressing the brake pedal firmly, operate the shift
lever. If the shift lever is operated without depressing the
brake pedal, the buzzer will sound and the shifting operation
will be disabled.
When selecting the shift position, make sure that the shift
position has been changed to the desired position by checking
the shift position indicator provided on the instrument cluster.
The shift position cannot be changed from P to B directly.