2012 Lexus CT200h light

580
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)
Have the vehicle inspected immediately.
A buzzer sounds and a warning message is shown on the multi-
information display. Failure to investigate the cause of the follow-
ing warnings may lead to the system operating abnormally and
possibly cause an accident. Have the vehicle inspected by any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
Warning messageDetails
Indicates a malfunction in the P position control
system
In this situation, there is a possibility that the
parking lock mechanism will not work.
When parking, park the vehicle on a flat surface
and apply the parking brake securely. Also, it
may not be possible to turn the “POWER”
switch off. If this happens, applying the parking
brake will enable the switch to be turned off.
(Flashes)
(If equipped)
Indicates a malfunction in the LED headlight sys-
tem

584
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)
Warning messageDetailsCorrection procedure
(Flashes)
Indicates, if the vehicle
reaches a speed of 5 km/
h (3 mph), that the park-
ing brake is still engaged
Release the parking
brake.
(Flashes)
Indicates that the
“POWER” switch is
turned off or turned to
ACCESSORY mode
and the driver’s door is
opened while the lights
are turned on.
Turn the lights off.
(If equipped)
Indicates that Lexus
parking assist-sensor is
dirty or covered with
ice
Clean the sensor.

590
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)
Have the malfunction repaired immediately.
After taking the specified steps to correct the suspected problem,
check that the warning message and light go off.
Interior
buzzerExte-
rior
buzzer
Warning messageDetailsCorrection
procedure
Once
(Flashes)
The electronic
key is not
detected when
an attempt is
made to start the
hybrid system.
Start the hybrid
system with the
electronic key
present.

596
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)
Interior
buzzerExte-
rior
buzzer
Warning messageDetailsCorrection
procedure

Power was
turned off due to
the automatic
power off func-
tion.
Next time when
starting the
hybrid system,
increase the
engine speed
slightly and
maintain that
level for approx-
imately 5 min-
utes to recharge
the 12-volt bat-
tery.
Once
The electronic
key has a low
battery.Replace the
electronic key
battery. (P.
527)

5
603
5-2. Steps to take in an emergency
When trouble arises
CT200h_OM_OM76067E_(EE)Slightly loosen the wheel nuts
(one turn).
Turn the tire jack portion “A”
by hand until the notch of the
jack is in contact with the jack
point.
The jack point guides are
located under the rocker panel.
They indicate the jack point
positions.
Raise the vehicle until the tire is
slightly raised off the ground.
STEP3
STEP4
STEP5

5
627
5-2. Steps to take in an emergency
When trouble arises
CT200h_OM_OM76067E_(EE)
If the hybrid system will not start
Reasons for the hybrid system not starting vary depending on the situ-
ation. Check the following and perform the appropriate procedure:
The hybrid system will not start even though the correct start-
ing procedure is being followed. (P. 198)
One of the following may be the cause of the problem:
The electronic key may not be functioning properly.
* (P.
630)
There may not be sufficient fuel in the vehicle’s tank.
Refuel the vehicle.
There may be a malfunction in the immobilizer system.
*
(P. 135)
There may be a malfunction in the P position control sys-
tem.
* (P. 202, 580)
*: It may not be possible to shift the shift position other than P.
The interior lights and headlights are dim, or the horn does not
sound or sounds at a low volume.
One of the following may be the cause of the problem:
The 12-volt battery may be discharged. (P. 508)
The 12-volt battery terminal connections may be loose or

628
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)
Emergency start function
When the hybrid system does not start, the following steps can be
used as an interim measure to start the hybrid system if the
“POWER” switch is functioning normally:
Set the parking brake.
Turn the “POWER” switch to ACCESSORY mode.
Press and hold the “POWER” switch for about 15 seconds
while depressing the brake pedal firmly.
Even if the hybrid system can be started using the above steps, the
system may be malfunctioning. Have the vehicle inspected by any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
The interior lights and headlights do not turn on, or the horn
does not sound.
One of the following may be the cause of the problem:
One or both of the 12-volt battery terminals may be discon-
nected.
The 12-volt battery may be discharged. (P. 508)
Contact any authorized Lexus dealer or repairer, or another duly
qualified and equipped professional if the problem cannot be
repaired, or if repair procedures are unknown.
STEP1
STEP2
STEP3

5
635
5-2. Steps to take in an emergency
When trouble arises
CT200h_OM_OM76067E_(EE)
Start the engine of the second vehicle. Increase the
engine speed slightly and maintain at that level for
approximately 5 minutes to recharge the battery of your
vehicle.
Open and close any of the doors of your vehicle with the
“POWER” switch off.
Maintain the engine speed of the second vehicle and start
the hybrid system of your vehicle by turning the
“POWER” switch to ON mode.
Make sure the “READY” indicator light comes on. If the
indicator light does not come on, contact any authorized
Lexus dealer or repairer, or another duly qualified and
equipped professional.
Once the hybrid system has started, remove the jumper
cables in the exact reverse order from which they were
connected.
To install the engine cover, conduct the removal proce-
dure in reverse. After installing, check that the fixed pins
are inserted securely.
Once the hybrid system starts, have the vehicle inspected at any
th i d L d l i th d l lifi dSTEP4
STEP5
STEP6
STEP7
STEP8
STEP9