2012 Lancia Musa warning

28
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Speed limit
This function is used to set the car
speed limit (km/h or mph); the driver
is immediately alerted when this limit
is exceeded (see section “Warning
lights and messages”).
To set the desired speed limit, proceed
as follows:
– briefly press MODE, the message
(speed limit) will appear on the dis-
play.
– press button +or–to select speed
limit activation (On) or deactivation
(Off);To cancel the setting, proceed as fol-
lows:
– briefly press button MODE: (On)
will flash on the display;
– press button +: (Off) will flash on
the display;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the settings. – if the function has been activated
(On), press buttons +or–to select the
required speed limit and then press
MODEto confirm.
NOTE The speed may be set in the
range from 30 to 250 km/h, or from
20 to 155 mph according to the pre-
viously chosen unit (see “Setting the
distance unit”) described below. The
setting will increase/decrease by five
units each time button +/–is
pressed. Hold button +/–pressed to
increase/decrease the setting rapidly.
Complete the setting by briefly press-
ing the button when you approach the
required setting.
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings.

29
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Adjusting the automatic
headlight sensor sensitivity
(light sensor)
(for versions/markets, where provided)
This function is used to adjust the
dusk sensor sensitivity to three levels
(level 1 = minimum, level 2 =
medium, level 3 = maximum); higher
the sensitivity, lower the quantity of
external light needed to switch the
headlights on. The device is set to
level “2” when the car is delivered.
Proceed as follows to set:
– briefly press button MODE, the pre-
viously set level will flash on the dis-
play;
– press button +or–for setting;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings.Turning Trip B on/off (Trip B)
This function may be used to activate
(On) or deactivate (Off) the Trip B
(partial trip).
For further information see “Trip
computer”.
Proceed as follows to turn on and off:
– briefly pressMODEON or OFF
flashes on the display (according to
the previous setting);
– press button +or–for setting;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings.Setting the clock
(Set clock)
This function is used to set the clock.
To carry out the adjustment, proceed
as follows:
– briefly press button MODE: the
“hours” will flash on the display;
– press button +or–to set;
– briefly press button MODE: “min-
utes” will start flashing on the display;
– press button +or–to set;
NOTE The setting will increase or de-
crease by one unit each time +or–is
pressed. Hold the button pressed to
increase/decrease the setting rapidly.
Complete the setting by briefly press-
ing the button when you approach the
required setting.
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings.

30
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Unlocking the doors and the
tailgate (key)
This function is used to: unlock the
front and rear doors, unlock the dri-
ver’s side door or all the doors includ-
ing the tailgate.
Proceed as follows to set:
– briefly press button MODE: “Open
doors”, “Open driver”, “Open all”;
– press button +or–to select. The se-
lected item will blink.
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings. – briefly press MODE: “month” will
start flashing on the display;
– press button +or–to set;
– briefly press button MODE: “day”
will start flashing on the display;
– press button +or–to set.
Note The setting will increase or de-
crease by one unit each time +or–is
pressed. Hold the button pressed to in-
crease/decrease the setting rapidly.
Complete the setting by briefly press-
ing the button when you approach the
required setting.
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings. 12h/24h clock mode
This function is used to select 12h or
24 h display.
To carry out the adjustment, proceed
as follows:
–briefly pressMODE: either 12h or
24h will start flashing on the display
(according to the previous setting);
– press button +or–for setting;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings.
Set date
This function is used to set the date
(year – month – day).
Proceed as follows to update:
– briefly press button MODE: “year”
will start flashing on the display;
– press +or–to adjust;

31
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
“Distance” unit of measure
This function is used to set the unit of
measure for distance (kilometres or
miles)
Proceed as follows to set the required
unit:
– briefly press MODE: (km) or (mi)
will start blinking on the display (ac-
cording to the previous setting);
– press button +or–for setting;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings.Proceed as follows to set:
– briefly press MODE: (km/l) or
(l/100km) will start flashing on the
display (according to the previous set-
ting);
– press button +or–for setting;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings. “Consumption” unit of measure
This function is used to set the unit of
measure for fuel consumption (km/l,
l/100 km or mpg) according to the
unit of measure selected in the previ-
ous paragraph (“Distance” unit of
measure).
If the distance unit set is “km” the
fuel consumption unit will be dis-
played in km/l or l/100km. If the dis-
tance unit set is “mi” the fuel con-
sumption unit will be displayed in
“mpg”.

32
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Adjusting the failure/warning
buzzer volume (Buzzer Volume)
This function allows the volume of the
buzzer which accompanies the display
of failures / warnings to be adjusted
(8 levels). To set the desired volume,
proceed as follows:
– briefly press button MODE: the pre-
viously set volume “level” starts flash-
ing on the display;
– press button +or–to set;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings. Selecting the language
The messages may be displayed in the
following languages: Italian, German,
English, Spanish, French, Portuguese.
To set the required language proceed
as follows:
– briefly press button MODE: the pre-
viously set “language” starts flashing
on the display;
– press button +or–for setting;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the settings. “Temperature” unit of measure
This function is used to set the unit of
measure for temperature (°C or °F).
Proceed as follows to set the required
unit:
– briefly press MODE(°C) or (°F)
will flash on the display (according to
the previous setting);
– press button +or–for setting;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings.

33
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Adjusting the button volume
(Button Vol.)
This function is used to set the volume
of the roger-beep accompanying the
activation of buttons MODE,+e–
through 8 levels.
To set the desired volume, proceed as
follows:
– briefly press button MODE: the pre-
viously set volume “level” starts flash-
ing on the display;
– press button +or–to set;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings.
S.B.R. buzzer reactivation
(Belt Buzzer)
(for versions/markets, where provided)
This function can be only displayed
after Lancia Dealership has deacti-
vated the S.B.R. system (see para-
graph “S.B.R. system” in section
“Safety devices”).The indications will appear more fre-
quently where there are 200 km left.
For 1.3 Multijet versions, refer to the
“Service Schedule” in the “Mainte-
nance and care” chapter for replacing
the air cleaner, the engine oil and the
engine oil filter. The indication will ap-
pear in kilometres or miles according
to the settings. When the next sched-
uled service operation is approaching,
the message “Service” will appear on
the display followed by the number of
kilometres or miles left when the key is
turned to MAR. The “Service Sched-
ule” information is provided with kilo-
metres (km)/miles (mi) or days (dd),
according to the deadline which ap-
pears first. Go to a Lancia Dealership
where the “Scheduled Service” opera-
tions will be performed and the mes-
sage will be reset. Scheduled Servicing (Service)
This function may be used to display
information connected to proper car
servicing in terms of kilometres or
days.
This information can be consulted as
follows:
–briefly press button MODE: service
in km or mi, according to previous
setting, will be displayed (see para-
graph “Units”);
– press button +or–to set deadline
in days;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen.
NOTE The “Service Schedule” re-
quires the car to be services every
20,000 km (or equivalent distance in
miles) or once a year. This message
will appear automatically with key at
MARafter 2,000 km (or equivalent
distance in miles) or 30 before the
deadline and will appear every 200
km (or equivalent distance in miles)
or 3 days.

34
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Activating/deactivating the
passenger front and side airbag
on/off (passenger bag)
(for versions/markets, where provided)
This function shall be used to acti-
vate/deactivate the passenger’s airbag.
Proceed as follows:
❒press MODEand after the message
(Bag pass Off) (deactivate) or (Bag
pass On) (activate) appears by
pressing buttons +and–, press the
MODEbutton again;
❒the confirmation request message
will be displayed;
❒press buttons +o–to select (Yes)
(to confirm activation/deactivation)
or (No) (to abort);
❒briefly press button MODE: the
display shows a message confirm-
ing the selected value. Now, go
back to the menu screen or press
the button for a prolonged time to
go back to the standard screen
without storing the settings.
MODE
MODE
MODE
– +
L0D2169g L0D2170g
L0D2171g L0D2172g
L0D2173g L0D2174gL0D2174g
L0D2175gL0D2176g
– +
– +
– +

35
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Quitting the menu
This function closes the cycle of set-
tings listed in the menu screen.
Briefly press button MODEto go
back to the standard screen without
storing the settings.
Press button +to return to the first
menu option (Speed Limit).Both functions can be reset (to start a
new trip). The following data can be
displayed for “General Trip”:
– Range
– Distance travelled
– Average consumption
– Instant consumption
– Average speed
– Travel time (driving time).
“Trip B” may be used to display the
figures relating to:
– Distance travelled B
– Average consumption B
– Average speed B
– Travel time B (driving time).
NOTE “Trip B” functions may be ex-
cluded (see “Trip B on”). “Range”
and “Instantaneous consumption”
cannot be reset. TRIP COMPUTER
(for versions/markets, where provided)
General features
The “Trip computer” is used to dis-
play information on car operation
when the key is turned to MAR. This
function consists of “General trip” for
displaying the complete mission of the
car and by “Trip B”, for trips; this
function is included in the general trip
information (as shown in fig. 30).