2012 Lancia Musa warning light

149
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
Bulbs Figure ref. Type Power
Main beam headlightsEH1 55W
Dipped beam headlights EH1 55W
Front sidelights AW5W 5W
Front fog lights (for versions/markets, where provided)EH1 55W
Front direction indicators BPY21W 21W
Side direction indicators AWY5W 5W
Rear direction indicators BPY21W 21W
Reversing lights BP21W 21W
Rear fog lights BP21W 21W
Number plate lights CC5W 5W
Front ceiling light AW5W 10W
Rear ceiling lightAW5W 10W
Rear ceiling lights (with sunroof)AW5W 5W
Boot light AW5W 5W

150
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
REPLACING
EXTERIOR BULBS
For the type of bulb and power rat-
ing, see “When needing to change a
bulb”.
FRONT LIGHT CLUSTER
The front light clusters contain side
lights, dipped beam, main beam and
direction indicator bulbs.
Remove the protective caps to remove
the side lights, the dipped beam and
the main beam headlights.
The bulbs are arranged inside the
light cluster fig. 17as follows:
Adipped beam headlights
Bmain beam headlights and Side-
lights
Cdirection indicators
After replacing, refit the protective
caps and check that they are secured
well.IMPORTANT Remove the engine
compartment fusebox B-fig. 18to ac-
cess the left headlights cover (in di-
rection of travel) for replacement.
fig. 18L0D0125mfig. 17L0D0157m
Before replacing bulbs,
wait for the engine to cool
down: RISK OF BURNS!
WARNING

151
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCYDIPPED BEAM HEADLIGHTS
fig. 19
To replace the bulb, proceed as fol-
lows:
❒
remove the protective cap;
❒disconnect the electrical connector
A-fig. 19;
❒release the bulb holder catch B, take
out the bulb Cand replace it;
❒fit the new bulb, ensuring that the
outline of the metal part coincides
with the grooves on the curve of the
headlight. Then reconnect the elec-
trical connector B and refasten the
bulb holder catch A;
❒after replacing the bulb, put the pro-
tective cap back into position.
MAIN BEAM HEADLIGHTS
fig. 20
To replace the bulb, proceed as fol-
lows:
❒
remove the protective cap;
❒disconnect the electric connector
A-fig. 20;
❒release the bulb holder catches B,
take out the bulb Cand replace it;
❒fit the new bulb, ensuring that the
outline of the metal part coincides
with the grooves on the curve of the
headlight. Then reconnect the elec-
trical connector Band refasten the
bulb holder catches A;
❒after replacing the bulb, put the pro-
tective cap back into position.
fig. 20L0D0159mfig. 19L0D0158m

152
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
DIRECTION INDICATORS
Front fig. 22
To change the bulb, proceed as fol-
lows:
❒turn the bulb holder anticlockwise
Aand pull it out;
❒remove the bulb Bby pushing it
slightly and turning it in an anti-
clockwise direction (bayonet
mount);
❒replace the bulb;
❒refit the bulb holder by turning it
clockwise and locking it properly.Side fig. 23
To change the bulb, proceed as fol-
lows:
❒lever in the point shown by the ar-
row in order to compress the fas-
tening spring and extract the unit
C;
❒turn the bulb holder Danticlock-
wise, extract the clipped bulb and
replace it;
❒refit the bulb holder Din the lens,
then position the assembly to the
unit making sure that the fastening
clip clicks.SIDE LIGHTS fig. 24
To change the bulbs, proceed as fol-
lows:
❒remove the protective cover releas-
ing the relevant catch;
❒remove snap-fitted bulb holder A,
remove the bulb Band replace it;
❒refit the snap-fitted bulb holder A;
❒refit the protective caps correctly
after replacing.
fig. 23L0C0148mfig. 22L0D0169mfig. 24L0D0520m

153
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
FRONT FOG LIGHTS fig. 25
(for versions/markets, where provided)
Contact a Lancia Dealership to re-
place the front fog lights.
fig. 25L0D0406m
REAR LIGHT CLUSTERS
LEDs are used for the taillights and
the brake lights. Contact a Lancia
Dealership in case of faults.
To change a direction indicator bulb,
proceed as follows:
❒open the tailgate;
❒turn the fastening deviceAanti-
clockwise (left flap) or clockwise
(right flap) and remove the cover;
❒disconnect the electric connector
C;
❒loosen the two fastening nuts B;
❒to remove the light cluster, pull
perpendicularly using the handle
present on the light cluster body;
❒press the bulb fastening tabs and
extract the bulb;
❒remove the bulb by pushing it
slightly and turning it anticlock-
wise;❒insert the bulb holder, making sure
that the two tabs are correctly fas-
tened; insert the light cluster inside
the housing and connect the elec-
tric connector C; fasten the two
nutsB; fasten the cover making
sure that the tabs are inserted in the
seat and turn the fastening device
Aanticlockwise (left flap) or clock-
wise (right flap) to secure it.
fig. 26L0D0187m
fig. 27L0D0188m

154
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
THIRD BRAKE LIGHTS
The third brake light fits LEDs. Con-
tact a Lancia Dealership in case of
faults.
fig. 28L0D0407m
NUMBER PLATE LIGHTS
fig. 29a
To change the bulbs, proceed as fol-
lows:
❒apply pressure to the point shown
by the arrow and remove lens A;
❒change the bulb Breleasing it from
the side contacts and making sure
the new bulb is correctly fastened
between the contacts;
❒withdraw the transparent cover as-
sembly.
fig. 29/aL0D0357mfig. 29/bL0D0426m
fig. 29/cL0D0427m
REAR FOG LIGHTS fig. 29/b
Go to a Lancia Dealership to replace
the rear fog light.
REVERSING LIGHTS fig. 29/c
Go to a Lancia Dealership to replace
the reversing light.

155
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
fig. 30L0D0193m
fig. 31L0D0194m
REPLACING AN
INTERIOR BULB
For the type of bulb and power rat-
ing, see “When needing to change a
bulb”.
FRONT CEILING LIGHT
fig. 30-31
To change the bulbs, proceed as fol-
lows:
❒operate in the points shown by the
arrows and remove light A;
❒open the protection lid B;
❒replace bulbs Creleasing them
from the side contacts; make sure
that new bulbs are correctly
clamped between contacts;
❒close the lid Band secure light A
into its housing locking it properly.
REAR CEILING LIGHT
fig. 32-33
To change the bulbs, proceed as fol-
lows:
❒operate in the points shown by the
arrows and remove light D;
❒open the protection lid E;
fig. 32L0D0195m
❒change the bulb Freleasing it from
the side contacts and making sure
the new bulb is correctly fastened
between the contacts;
❒close the protection lid Eand se-
cure light Dinto its housing lock-
ing it properly.
fig. 33L0D0196m

156
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
BOOT LIGHT fig. 34
To change the bulb, proceed as fol-
lows:
❒open the tailgate;
❒remove the light Alevering in the
point shown by the arrow.
❒open the protection Band replace
the snap-fitted bulb;
❒re-close the protective cover Bon
the lens;
❒refit the light Ainserting it in its
correct position firstly on one end
and then on the other until it
clicks into place.
fig. 34L0D0197m
REPLACING FUSES
INTRODUCTION fig. 35
The fuse is a protective device for the
electric system: it comes into action
(i.e. it cuts off) mainly due to a fault
or improper action on the system.
Check the efficiency of the corre-
sponding fuse when a device does not
work: the conducting element Amust
not be interrupted. If it is, replace the
blown fuse with another with the
same amperage (same colour).
B: intact fuse
C: fuse with damaged filament.
Use the tongs Din the fusebox on the
dashboard to change a fuse.
fig. 35L0D0198m
If a fuse blows again, con-
tact a Lancia Dealership.
WARNING
Never replace a fuse with
another of higher amper-
age: FIRE RISK.
If a general protection fuse
(MEGA-FUSE, MIDI-
FUSE, MAXI-FUSE) blows, con-
tact your Lancia Dealership
WARNING
Remove the key from the
ignition switch and switch
off all loads before replacing a
fuse.
WARNING
If a general protection fuse
for safety systems (air bag
system, braking system), power
unit systems (engine system, trans-
mission system) or steering system
is triggered, contact a Lancia
Dealership.
WARNING