CAUTION!
Using a transmission fluid other than the
manufacturer’s recommended fluid may
cause deterioration in transmission shift qual-
ity and/or torque converter shudder. Using a
transmission fluid other than the manufactur-
er’s recommended fluid will require more fre-
quent fluid and filter changes. Refer to “Fluids,
Lubricants, and Genuine Parts” in “Maintain-
ing Your Vehicle” for further information.
Special Additives
Automatic Transmission Fluid (ATF) is an engi-
neered product and its performance may be
impaired by supplemental additives. Therefore,
do not add any fluid additives to the transmis-
sion. The only exception to this policy is the use
of special dyes to aid in detecting fluid leaks. In
addition, avoid using transmission sealers as
they may adversely affect seals.CAUTION!
Do not use chemical flushes in your transmis-
sion as the chemicals can damage your trans-
mission components. Such damage is not
covered by the New Vehicle Limited Warranty.
Fluid Level Check – 3.6L And 3.0L Diesel
Engine
Routine fluid level checks are not required. For
this reason, the dipstick is omitted. Your autho-
rized dealer can check your transmission fluid
level using a special service dipstick.
If you notice fluid leakage or transmission mal-
function, have your authorized dealer check
the transmission fluid level. Operation with an
improper fluid level can greatly reduce the life
of your transmission.CAUTION!
• Using a transmission fluid other than the
manufacturer’s recommended fluid may
cause deterioration in transmission shift
quality and/or torque converter shudder.
Using a transmission fluid other than that
recommended by the manufacturer will re-
quire more frequent fluid and filter changes.
Refer to “Fluids, Lubricants, and Genuine
Parts” in “Maintaining Your Vehicle” for fur-
ther information.
• The fluid level is preset at the factory and it
does not require adjustment under normal
operating conditions. If a transmission fluid
leak occurs, visit your authorized dealer
immediately. Severe damage to the trans-
mission may occur. Your authorized dealer
has the proper tools to adjust the fluid level
accurately.
314
Fluid Level Check – 5.7L Engine
Check the fluid level while the transmission is at
normal operating temperature. This occurs af-
ter at least 15 miles (25 km) of driving. At
normal operating temperature the fluid cannot
be held comfortably between the fingertips.
To check the fluid level properly, the following
procedure must be used:
1. Operate the engine at idle speed and nor-
mal operating temperature.
2. The vehicle must be on level ground.
3. Fully apply the parking brake, and press the
brake pedal.
4. Place the shift lever momentarily in each
gear position ending with the shift lever in
PARK.
5. Remove the dipstick, wipe it clean and
reinsert it until seated.6. Remove the dipstick again, and note the
fluid level on both sides. The fluid level should
be between the “HOT” (upper) reference holes
on the dipstick at normal operating tempera-
ture. The fluid level is only valid if there is a solid
coating of oil on both sides of the dipstick. If the
fluid is low, add as required into the dipstick
tube.
Do not overfill. After adding any quantity
of oil through the oil fill tube, wait a minimum of
two minutes for the oil to fully drain into the
transmission before rechecking the fluid level.
NOTE:
If it is necessary to check the transmission
below the operating temperature, the fluid
level should be between the two “COLD”
(lower) holes on the dipstick with the fluid at
approximately 70°F (21°C) (room tempera-
ture). If the fluid level is correctly estab-
lished at room temperature, it should be
between the “HOT” (upper) reference holes
when the transmission reaches 180°F
(82°C). Remember it is best to check the
level at the normal operating temperature.CAUTION!
Be aware that if the fluid temperature is below
50°F (10°C) it may not register on the dipstick.
Do not add fluid until the temperature is
elevated enough to produce an accurate
reading.
7. Check for leaks. Release parking brake.
To prevent dirt and water from entering the
transmission after checking or replenishing
fluid, make certain that the dipstick cap is
properly reseated. It is normal for the dipstick
cap to spring back slightly from its fully seated
position, as long as its seal remains engaged in
the dipstick tube.
Appearance Care And Protection
From Corrosion
Protection Of Body And Paint From
Corrosion
Vehicle body care requirements vary according
to geographic locations and usage. Chemicals
that make roads passable in snow and ice, and
those that are sprayed on trees and road
315
Plastic is not as scratch-resistant as glass and
therefore different lens cleaning procedures
must be followed.
To minimize the possibility of scratching the
lenses and reducing light output, avoid wiping
with a dry cloth. To remove road dirt, wash with
a mild soap solution followed by rinsing.
Do not use abrasive cleaning components,
solvents, steel wool or other aggressive mate-
rial to clean the lenses.
Glass Surfaces
All glass surfaces should be cleaned on a
regular basis with MOPARGlass Cleaner or
any commercial household-type glass cleaner.
Never use an abrasive type cleaner. Use cau-
tion when cleaning inside rear windows
equipped with electric defrosters. Do not use
scrapers or other sharp instruments which may
scratch the elements.
When cleaning the rearview mirror, spray
cleaner on the towel or rag that you are using.
Do not spray cleaner directly on the mirror. Cleaning Plastic Instrument Cluster Lenses
The lenses in front of the instruments in this
vehicle are molded in clear plastic. When
cleaning the lenses, care must be taken to
avoid scratching the plastic.
1. Clean with a wet soft rag. A mild soap
solution may be used, but do not use high
alcohol content or abrasive cleaners. If soap is
used, wipe clean with a clean damp rag.
2. Dry with a soft cloth.
Seat Belt Maintenance
Do not bleach, dye or clean the belts with
chemical solvents or abrasive cleaners. This
will weaken the fabric. Sun damage will also
weaken the fabric.
If the belts need cleaning, use MOPAR
Total
Clean, a mild soap solution, or lukewarm water.
Do not remove the belts from the vehicle to
wash them. Dry with a soft cloth.
Replace the belts if they appear frayed or worn
or if the buckles do not work properly.FUSES
Totally Integrated Power Module
The Totally Integrated Power Module is located
in the engine compartment. This center con-
tains cartridge fuses and mini fuses. A descrip-
tion of each fuse and component may be
stamped on the inside cover, otherwise the
cavity number of each fuse is stamped on the
inside cover that corresponds to the following
chart.
Totally Integrated Power Module
318
FLUID CAPACITIES
U.S.Metric
Fuel (Approximate)
All Engines 24.6 Gallons93 Liters
Engine Oil with Filter
3.6L Engine (SAE 5W-30, API Certified) 6 Quarts5.6 Liters
5.7L Engine (SAE 5W-20, API Certified) 7 Quarts6.6 Liters
3.0L Diesel Engine (SAE 5W-30 Synthetic, API Certified Low Ash) 10 Quarts9.5 Liters
Cooling System *
3.6L Engine (MOPAR Engine Coolant/Antifreeze 5-Year/100,000 Mile Formula or
equivalent) 10.4 Quarts
9.9 Liters
5.7 Liter Engine (MOPAR Engine Coolant/Antifreeze 5-Year/100,000 Mile Formula
or equivalent) – Without Trailer Tow Package 15.4 Quarts
14.6 Liters
5.7 Liter Engine (MOPAR Engine Coolant/Antifreeze 5-Year/100,000 Mile Formula
or equivalent) – With Trailer Tow Package 16 Quarts
15.2 Liters
3.0L Diesel Engine (MOPAR Engine Coolant/Antifreeze 5-Year/100,000 Mile For-
mula or equivalent) 13.9 Quarts
13.2 Liters
* Includes heater and coolant recovery bottle filled to MAX level.
326
FLUIDS, LUBRICANTS, AND GENUINE PARTS
Engine
ComponentFluid, Lubricant, or Genuine Part
Engine Coolant MOPARAntifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technol-
ogy) or equivalent.
Engine Oil – Non ACEA Categories
(3.6L Engine) Use API Certified SAE 5W-30 engine oil, meeting the requirements of Chrysler Material Standard
MS-6395. Refer to your engine oil filler cap for correct SAE grade.
Engine Oil – ACEA Categories
(3.6L Engine) For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine oils
meeting the requirements of ACEA C3, and approved to MB 229.31 or MB 229.51.
Engine Oil – Non ACEA Categories
(5.7L Engine) Use API Certified SAE 5W-20 engine oil, meeting the requirements of Chrysler Material Standard
MS-6395. Refer to your engine oil filler cap for correct SAE grade. SAE 5W-30 engine oil ap-
proved to MB 229.31 or MB 229.51 may be used when SAE 5W-20 engine oil is not available.
Engine Oil – ACEA Categories
(5.7L Engine) For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine oils
meeting the requirements of ACEA C3, and approved to MB 229.31 or MB 229.51. SAE 5W-30
engine oil approved to MB 229.31 or MB 229.51 may be used when SAE 5W-20 engine oil is not
available.
Engine Oil – 3.0L Diesel Engine Use SAE 5W-30 Synthetic Low Ash Engine Oil, meeting the requirements of Chrysler Material
Standard MS-11106 and approved to MB 229.31 or MB 229.51 and ACEA C3.
Engine Oil Filter MOPAREngine Oil Filter or equivalent.
Spark Plugs – 3.6L Engine RER8ZWYCB4 (Gap 0.043 in [1.1 mm])
327
ComponentFluid, Lubricant, or Genuine Part
Spark Plugs – 5.7L Engine LZFR5C–11G (Gap 0.043 in [1.1 mm])
Fuel Selection – 3.6L Engine 91 Octane
Fuel Selection – 5.7L Engine 91 Octane Acceptable - 95 Octane Recommended
Fuel Selection – 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle. The manufacturer requires
that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum)
and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid dam-
age to the emissions control system. For most year-round service, No. 2 diesel fuel meeting ASTM
specification D-975 Grade S15 will provide good performance. If the vehicle is exposed to extreme
cold (below 20F or -7C), or is required to operate at colder-than-normal conditions for prolonged
periods, use climatized No. 2 diesel fuel or dilute the No. 2 diesel fuel with 50% No. 1 diesel fuel.
This will provide better protection from fuel gelling or wax-plugging of the fuel filters. This vehicle is
fully compatible with biodiesel blends up to 5% biodiesel meeting ASTM specification D-975.
328
Chassis
ComponentFluid, Lubricant, or Genuine Part
Automatic Transmission MOPARATF+4Automatic Transmission Fluid or equivalent licensed ATF+4 product.
Transfer Case MOPARATF+4Automatic Transmission Fluid or equivalent licensed ATF+4 product.
Axle Differential (Front-Rear) MOPARSynthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent with friction
modifier additive.
Axle Differential (Rear) – 5.7L Engine With
Electronic Limited-Slip Differential (ELSD) MOPAR
Synthetic Gear & Axle Lubricant SAE 75W-90 (API-GL5) or equivalent.
Axle Differential (Rear) – 5.7L Engine Without
Electronic Limited-Slip Differential (ELSD) MOPAR
Synthetic Gear & Axle Lubricant SAE 75W-85 (API-GL5) or equivalent.
Brake Master Cylinder MOPARDOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not
available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent.
Power Steering Reservoir – 3.6L Engine and
3.0L Diesel Engine MOPAR
Hydraulic Fluid or equivalent meeting MS-11655, such as Fuchs EG ZH 3044 or Pento-
sin CHF 11s.
Power Steering Reservoir – 5.7L Engine MOPAR Power Steering Fluid +4, MOPAR ATF+4Automatic Transmission Fluid or equivalent
licensed ATF+4 product.
329
8
MAINTENANCE SCHEDULES
•MAINTENANCE SCHEDULE .................... 332
• Maintenance Schedule – Gasoline Engine ......... 332
• Maintenance Schedule – Diesel Engine ........... 344
331