2012 INFINITI G37 buttons

Black plate (237,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SEEK tuning/CATEGORY (CAT): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
. For AM and FM radio
Push the SEEK·CAT or TRACK button
or to tune from low to high or high
to low frequencies and to stop at the
next broadcasting station.
. For XM Satellite Radio
Push the SEEK·CAT or TRACK button
or to tune to the first channel of the
next or previous category.
During satellite radio reception, the follow-
ing notices will be displayed under certain
conditions.
. NO SIGNAL (No signal is received while
the SAT tuner is connected.)
. OFF AIR (Broadcasting signed off)
. CHECK ANTENNA (Antenna connection
error)
. LOADING (When the initial setting is
performed)
. UPDATING (When the satellite radio
subscription is not active)
or SCAN tuning: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the SCAN tuning button to tune from
low to high frequencies and stop at each
broadcasting station/channel for 5 sec- onds. Pushing the button again during this
5 seconds period will stop SCAN tuning
and the radio will remain tuned to that
station/channel.
If the SCAN tuning button is not pushed
within 5 seconds, SCAN tuning moves to
the next station/channel.
PRESET select (Type B): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the PRESET select button to go to the
next PRESET. After choosing from the
PRESET A, B or C, you can select the
desired station using the INFINITI controller
or pushing the station preset buttons
* 1
to
* 6
.
* 1
to
* 6
Station memory operations (Type
A): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
12 stations/channels can be set for the FM
band (6 each for FM1 and FM2), 18 for XM
radio (6 each for XM1, XM2 and XM3) and 6
stations can be set for the AM band.
1. Choose the radio band using the radio
band select button.
2. Tune to the desired station/channel
using the SEEK·CAT, TRACK, SCAN
button or the radio TUNE knob.
3. Push and hold the desired station
preset button
* 1
to
* 6
until the radio mutes.
4. The station indicator will then come on
and the sound will resume. Memorizing
is now complete.
5. Other buttons can be set in the same
manner.
If the battery cable is disconnected, or if
the fuse opens, the radio memory will be
erased. In that case, reset the desired
stations/channels.
* 1
to
* 6
Station memory operations (Type
B): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
6 stations/channels can be set for PRESET
A, B and C. The PRESET A, B and C function
allows you to store a combination of FM,
AM and XM stations/channels for easy
access.
1. Choose preset stations A, B or C using
the preset select button.
2. Tune to the desired stations/channels
using the SEEK, SCAN or TUNE button.
3. Select the desired stations/channels
and push and hold the desired stations
preset button
* 1
to
* 6
until a beep
sound is heard. (The radio mutes when
the select button is pushed.)
Monitor, climate, audio, phone and voice recognition systems
4-59

Black plate (238,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-60 Monitor, climate, audio, phone and voice recognition systems4. The stations indicator will then come on
and the sound will resume. Memorizing
is now complete.
5. Other buttons can be set in the same
manner.
If the battery cable is disconnected, or if
the fuse opens, the radio memory will be
erased. In that case, reset the desired
stations/channels.
List (AM and FM radio) (models with
navigation system): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the “ List ” key on the display is
selected while the FM or AM radio is being
played, the preset station list will be
displayed.
If 1 of the 6 preset stations listed is
touched and held, the current station will
be stored as the new preset.
Menu (XM Satellite Radio) (models with
navigation system): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the “ Menu ” key on the display is
selected while the XM Satellite Radio is
being played, the menu list will be
displayed.
The following items are available.
. Preset List
Displays the preset channel list. If 1 of the 6 preset stations listed is touched
and held, the current station will be
stored as the new preset.
. Customize Channel List
Selects specific channels to skip while
using the TUNE, SEEK/CATEGORY or
Menu-Categories feature.
. Favorite Artists & Songs
Stores the current artist or song that is
being played. Touch the “ Alert ” key to
be reminded when the stored artist or
song is playing on a station while
listening to XM.
. Categories
Selecting a category will go to the first
channel in that category as defined by
XM Radio.
. Direct Tune
Inputs the channel number by using a
keypad.
Text (models without navigation system): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the “ Text ” key is selected with the
INFINITI controller on the display and then
the ENTER button is pushed while the
satellite radio is being played, the text
information listed below will be displayed
on the screen. . CH Name
. Category
. Name
. Title
. Other
Compact Disc (CD) player operation GUID-92C6C7F8-3A3B-42D9-B8DF-915DA610B375
Push the ignition switch to the ACC or ON
position and insert the Compact Disc (CD)
into the slot with the label side facing up.
The CD will be guided automatically into
the slot and start playing.
After loading the CD, the number of tracks
on the CD and the play time will appear on
the display.
If the radio is already operating, it will
automatically turn off and the CD will play.
If the system has been turned off while the
CD was playing, pushing the ON·OFF
button will start the CD.
Do not use 3.1 in (8 cm) discs.
or PLAY: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the DISC·AUX or DISC (CD play)
button is pushed with the system off and
the CD loaded, the system will turn on and
the CD will start to play.

Black plate (254,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-76 Monitor, climate, audio, phone and voice recognition systems. Second generation iPod touch ®
(version
1.2.3 or later)
. First generation iPod nano ®
(version
1.3.1 or later)
. Second generation iPod nano ®
(version
1.1.3 or later)
. Third generation iPod nano ®
(version
1.1 or later)
. Fourth generation iPod nano ®
(version
1.0.2 or later)
Models without navigation system: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
. Fifth generation iPod ®
(firmware ver-
sion 1.3)
. First generation iPod Classic ®
(firmware
version 1.1.2 PC)
. Second generation iPod Classic ®
(firm-
ware version 2.0 PC)
. First generation iPod touch ®
(firmware
version 2.1)
. Second generation iPod touch ®
(firm-
ware version 2.1.1)
. First generation iPod nano ®
(firmware
version 1.3.1)
. Second generation iPod nano ®
(firm-
ware version 1.1.3)
. Third generation iPod nano ®
(firmware
version 1.1 PC) . Third generation iPhone ®
(firmware
version 2.1)
Make sure that the iPod ®
version is
updated.
Audio main operation GUID-12FEF761-1E1C-44EA-A5B7-774957A975FE
Push the ignition switch to the ACC or ON
position. Then, push the DISC·AUX or DISC
button repeatedly to switch to the iPod ®
mode.
If the system has been turned off while the
iPod ®
was playing, pushing the ON·OFF
button will start the iPod ®
.
or PLAY: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the DISC·AUX or AUX button is
pushed with the system off and the iPod ®
connected, the system will turn on. If
another audio source is playing and the
iPod ®
is connected, push the DISC·AUX or
AUX button repeatedly until the center
display changes to the iPod ®
mode.
Interface: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The interface for iPod ®
operation shown on
the vehicle center display is similar to the
iPod ®
interface. Use the INFINITI controller
and the ENTER or BACK button to play the
iPod ®
with your favorite settings. The following items can be chosen from the
menu list screen. For further information
about each item, see the iPod ®
Owner ’ s
Manual.
. Now Playing
. Playlists
. Artists
. Albums
. Songs
. Podcasts
. Genres
. Composers
. Audiobooks
. Shuffle Songs
The following touch-panel buttons shown
on the screen are also available:
.
: returns to the previous screen.
. : plays/pauses the music selected.
Next/Previous Track and Fast
Forward/Rewind: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the or button is pushed for
more than 1.5 seconds while the iPod ®
is
playing, the iPod ®
will play while fast
forwarding or rewinding. When the button
is released, the iPod ®
will return to the
normal play speed.

Black plate (270,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-92 Monitor, climate, audio, phone and voice recognition systems SAA1772
CONTROL BUTTONS GUID-0B868A4F-9B5D-45FD-8767-9633BA3ABBBF
1) PHONE button
2) TALK /PHONE SEND button SAA2519
CONNECTING PROCEDURE GUID-5001AC50-4CF3-478F-AA37-19C8B982C9BF
1. Push the PHONE button or the
button, and select the “ Connect Phone ”
key. SAA2520
2. When a PIN code appears on the
screen, operate the compatible Blue-
tooth ®
cellular phone to enter the PIN
code.
The connecting procedure of the cellu-
lar phone varies according to each
cellular phone. See the cellular phone
Owner ’ s Manual for the details. You can
also visit
www.InfinitiUSA.com/bluetooth or call
INFINITI Consumer Affairs Department
for instructions on pairing INFINITI
recommended cellular phones.
When the connection process is com-
pleted, the screen will return to the

Black plate (280,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-102 Monitor, climate, audio, phone and voice recognition systemsBluetooth trademark: Bluetooth ®
is a trademark
owned by Bluetooth SIG, Inc.,
and licensed to Visteon Cor-
poration.
SAA1582
CONTROL BUTTONS GUID-CFC00FC5-3386-4E13-A3FA-5089B0478C66
1. PHONE SEND button
Push the button to initiate a VR
session or answer an incoming call.
You can also use the button to skip
through system feedback and to enter
commands during a call.
2. PHONE END
button
Push the button to cancel a VR
session or end a call. VOICE RECOGNITION SYSTEM GUID-F0B91240-344B-4DA1-9F15-ED4E510BF802
You can also use the Bluetooth ®
hands-
free phone system with Voice Recognition
System.
INFO
. The available voice commands are only
applicable to the relevant language set
in the LANGUAGE setting screen. (See
“ How to use SETTING button ” (P.4-14).)
. If the vehicle is in motion, some
commands may not be available so full
attention may be given to vehicle
operation.
Using system GUID-E9016D80-4CEA-422A-BE05-320EA92AC5F3
Initialization: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the ignition switch is pushed to the
ON position, Voice Recognition System is
initialized, which may take up to one
minute. When completed, the system is
ready to accept voice commands. If the
switch on the steering wheel is pushed
before the initialization completes, the
system will not accept any command.
Before starting: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
To get the best performance out of the
Voice Recognition System, observe the
following:

Black plate (282,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-104 Monitor, climate, audio, phone and voice recognition systemscommand recognition mode .
4. The system acknowledges the com-
mand and announces the next set of
available commands.
5. After the tone sounds, speak the phone
number.
6. When you have finished speaking the
phone number, the system repeats it
back and announces the available
commands.
7. After system responds, speak “ Dial ”
and the system dials the spoken
numbers.
Operating tips: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
. Voice commands cannot be accepted
when the icon is
.
. If the command is not recognized, the
system announces, “ Please say again ” .
Repeat the command in a clear voice.
. Push the
switch or the BACK button
once to return to the previous screen.
. If you want to cancel the command,
push the
switch. The message
“ Voice input is canceled ” will be
announced. If you want to adjust the
volume of the system feedback, push
the volume control buttons [+] or [ − ] on
the steering wheel or use the audio system volume knob while the system
is making an announcement.
How to speak commands: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The Voice Recognition System requires a
certain way to speak voice commands.
Speak normally and clearly in the direction
of the microphone (located in front of the
rearview mirror). Every digit of the number
must be spoken individually and in a
normal manner. The hands-free mode will
work best when the telephone number is
spoken in blocks of three to five digits.
After each spoken block is terminated, the
system will repeat the three to five digits
and wait for you to speak the next digit or
block of digits required for the telephone
number.
See “ List of voice commands ” (P.4-106) for
the appropriate commands that can be
spoken for the hands-free mode system.
Example:
In order to initiate a call, speak “ Phone-
book ” .
INFO
. If you are controlling the telephone
system by voice command for the first
time or do not know the appropriate
voice command, speak “ Help ” . The system announces the available com-
mands.
. When you speak numbers, you can
speak both “ zero ” or “ oh ” for “ 0 ” .
Personal vocabulary (voicetags): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Voice Recognition System is equipped with
the function called “ voicetags ” , which can
be associated with the phone number and
name in the phonebook. Using the voice
tag will automatically generate a speed
dial to the registered number.
See “ Phonebook registration ” (P.4-108).
You can call the identified number using
the following command: “ Dial ” followed by
the voice tag.
Dialling a name with a voice tag: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
It is possible to call up a name via a voice
tag instead of a number, provided the
name and number of your correspondent
has been previously stored in the phone-
book.
Dial via a voice tag, according to the
following procedure.
1. Push the
switch.
2. The system replies “ please say a
command after the beep. Available
commands are: Call, Phonebook, Re-

Black plate (297,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SAA2535
2. A list of commands appears on the
screen, and the system announces,
“ Would you like to access Phone,
Navigation, Information, Audio or
Help? ” .
3. After the tone sounds and the icon on
the screen changes from
to ,
speak a command.
Selecting the “ Practice ” key will start
the practice mode. See “ Let ’ s Practice ”
(P.4-117).
4. Continue to follow the voice menu
prompts and speak after the tone
sounds until your desired operation is
completed. Selecting the “ Help ” key can display
the detailed information of the each
command.
Operating tips: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
. Say a command after the tone.
. Commands that are available are al-
ways shown on the display and spoken
through voice menu prompts. Com-
mands other than those that are dis-
played are not accepted. Please follow
the prompts given by the system.
. If the command is not recognized, the
system announces, “ Please say again ” .
Repeat the command in a clear voice.
. Push the BACK button once to return to
the previous screen.
. To exit the voice recognition system,
push and hold the TALK
switch. The
message, “ Voice canceled ” will be
announced.
. To skip the voice guidance function and
give the command immediately, press
the TALK
switch to interrupt the
system. Remember to speak after the
tone.
. If you want to adjust the volume of the
system feedback, push the volume
control buttons [+] or [ − ] on the steering switch or use the audio system
volume knob while the system is
making an announcement.
How to speak numbers: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
INFINITI Voice Recognition requires a cer-
tain way to speak numbers when giving
voice commands. Refer to the following
examples.
General rule
Only single digits 0 (zero) to 9 can be used.
(For example, if you would like to say 500,
“ five zero zero ” can be used, but “ five
hundred ” cannot.)
Examples
. 1-800-662-6200
— “ One eight zero zero six six two six
two zero zero ”
Improving Recognition of Phone numbers
You can improve the recognition of phone
numbers by saying the phone number in
three groups of numbers. For example,
when you try to call 800-662-6200, say
“ eight zero zero ” first, and the system will
then ask you for the next three digits. Then,
say “ six six two ” . After recognition, the
system will then ask for the last four digits.
Say, “ six two zero zero ” . Using this method
Monitor, climate, audio, phone and voice recognition systems
4-119

Black plate (433,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]5. Push the buttons two or three times to
check its operation.
See an INFINITI retailer if you need any
assistance for replacement.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference that
may cause undesired operation.
NOTE:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user ’ s authority
to operate the equipment.
For Canada:
This device complies with RSS-210 of
Industry Canada. Operation is subject to
the following two conditions: (1) this
device may not cause interference, and
(2) this device must accept any interfer-
ence, including interference that may
cause undesired operation of the device.
Maintenance and do-it-yourself
8-27