2012 INFINITI G37 steering wheel

Black plate (94,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-16 Instruments and controlsWARNING. If the light does not illuminate with the
ignition switch pushed ON, have the
vehicle checked by an INFINITI retailer as
soon as possible.
. If the light illuminates while driving,
avoid sudden steering maneuvers or
abrupt braking, reduce vehicle speed,
pull off the road to a safe location and
stop the vehicle as soon as possible.
Driving with under-inflated tires may
permanently damage the tires and in-
crease the likelihood of tire failure.
Serious vehicle damage could occur
and may lead to an accident and could
result in serious personal injury. Check
the tire pressure for all four tires. Adjust
the tire pressure to the recommended
COLD tire pressure shown on the Tire
and Loading Information label to turn
the low tire pressure warning light OFF. If
the light still illuminates while driving
after adjusting the tire pressure, a tire
may be flat. If you have a flat tire,
replace it with a spare tire as soon as
possible. . When a spare tire is mounted or a wheel
is replaced, the TPMS will not function
and the low tire pressure warning light
will flash for approximately 1 minute.
The light will remain on after the 1
minute. Contact your INFINITI retailer as
soon as possible for tire replacement
and/or system resetting.
. Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
CAUTION . The TPMS is not a substitute for the
regular tire pressure check. Be sure to
check the tire pressure regularly.
. If the vehicle is being driven at speeds of
less than 16 MPH (25 km/h), the TPMS
may not operate correctly.
. Be sure to install the specified size of
tires to the four wheels correctly.
Master warning light GUID-BFD238A1-B056-42EA-B9A0-FCCF2B17501F
When the ignition switch is in the ON
position, the master warning light illumi- nates if any of the following are displayed
on the dot matrix liquid crystal display:
. No key warning
. Low fuel warning
. Low washer fluid warning
. Parking brake release warning
. Door/trunk open warning
. Loose fuel cap warning
. Check tire pressure warning
See “ Dot matrix liquid crystal display ” (P.2-
20).
Preview Function warning light
(orange; if so equipped) GUID-B4E486C7-1748-4EBD-A37A-79C9F389E7E0
The light comes on if there is a malfunction
in the Brake Assist (with Preview Function)
system.
If the warning light comes on, park the
vehicle in a safe place. Turn the engine off,
restart the engine, resume driving and set
the ICC system again.
If it is not possible to set the system or the
indicator stays on, it may indicate that the
system is malfunctioning. Although the
vehicle is still driveable under normal
conditions, have the vehicle checked at
an INFINITI retailer.

Black plate (118,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-40 Instruments and controls GUID-9C1E6002-FE1D-4E74-971F-A1B3941CE624
SIC3312
To sound the horn, push the center pad
area of the steering wheel.
WARNINGDo not disassemble the horn. Doing so
could affect proper operation of the supple-
mental front air bag system. Tampering with
the supplemental front air bag system may
result in serious personal injury. GUID-DD74E04E-57D9-472E-AB2F-AEAAA9BBBD37
WARNING Do not use or allow occupants to use the
seat heater if you or the occupants cannot
monitor elevated seat temperatures or have
an inability to feel pain in body parts that
contact the seat. Use of the seat heater by
such people could result in serious injury.
CAUTION . The battery could run down if the seat
heater is operated while the engine is
not running.
. Do not use the seat heater for extended
periods or when no one is using the
seat.
. Do not put anything on the seat which
insulates heat, such as a blanket,
cushion, seat cover, etc. Otherwise, the
seat may become overheated.
. Do not place anything hard or heavy on
the seat or pierce it with a pin or similar
object. This may result in damage to the
heater. . Any liquid spilled on the heated seat
should be removed immediately with a
dry cloth.
. When cleaning the seat, never use
gasoline, thinner, or any similar materi-
als.
. If any abnormalities are found or the
heated seat does not operate, turn the
switch off and have the system checked
by an INFINITI retailer.HORN HEATED SEATS (if so equipped)

Black plate (168,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-26 Pre-driving checks and adjustments GUID-0A2F0EF8-70E0-4509-BE3C-E077A7541106
WARNING. Do not adjust the steering wheel while
driving. You could lose control of your
vehicle and cause an accident.
. Do not adjust the steering wheel any
closer to you than is necessary for
proper steering operation and comfort.
The driver ’ s air bag inflates with great
force. If you are unrestrained, leaning
forward, sitting sideways or out of
position in any way, you are at greater
risk of injury or death in a crash. You
may also receive serious or fatal injuries
from the air bag if you are up against it
when it inflates. Always sit back against
the seatback and as far away as practical
from the steering wheel. Always use the
seat belts. SPA2328
MANUAL OPERATION (if so
equipped) GUID-E531E01C-480F-4832-8A2F-7DB7D1BBD55C
Tilt or telescopic operation GUID-44ED5F8C-B493-4F4C-B6AB-0E69748E95E6
Pull the lock lever
* 1
down and adjust the
steering wheel up, down, forward or rear-
ward to the desired position.
Push the lock lever up securely to lock the
steering wheel in place. SPA2312
ELECTRIC OPERATION (if so
equipped) GUID-010C7211-B94D-440E-A135-0E0FDA1DB257
Tilt or telescopic operation GUID-8DDEF560-46B7-49C3-B657-4DA748B62330
Move the lever to adjust the steering wheel
up or down, forward or rearward to the
desired position.
Entry/Exit function operation (if so
equipped): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The automatic drive positioner system will
make the steering wheel move up auto-
matically when the driver ’ s door is opened
with the ignition switch in the LOCK
position. This lets the driver get into andTILT/TELESCOPIC STEERING

Black plate (173,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]VANITY MIRROR GUID-418E781F-468D-4640-B3BF-4DA5D9BE4DFA
To use the front vanity mirror, pull down
the sun visor and pull up the cover. GUID-3EDC2AC8-B979-442D-AEB4-1AF89546AADA
The automatic drive positioner system has
three features:
. Entry/exit function (Automatic Trans-
mission Sedan models)
. Seat synchronization function
. Memory storage
ENTRY/EXIT FUNCTION (Automatic
Transmission Sedan models) GUID-30995ABA-8234-45F4-9B5C-ECA6C07F73E6
This system is designed so that the driver ’ s
seat and steering column will automati-
cally move when the automatic transmis-
sion selector lever is in the P (Park)
position. This allows the driver to get into
and out of the driver ’ s seat more easily.
The driver ’ s seat will slide backward and
the steering wheel will move up when the
driver ’ s door is opened with the ignition
switch in the LOCK position.
The driver ’ s seat and steering wheel will
return to the previous positions when one
of the following is operated:
. When the ignition switch is pushed to
the ACC position after the driver ’ s door
is closed.
. When the ignition switch is pushed to
the ON position.
. When the Intelligent Key is inserted into the port after the driver ’ s door is
closed.
The driver ’ s seat will not return to the
previous positions if the seat or steering
adjusting switch is operated when the seat
is at the exit position.
Cancel or activate entry/exit func-
tion GUID-8D71F741-560B-4B4E-AA55-F9F223C96E4F
The selector lever must be in the P (Park)
position with the ignition switch in the OFF
position.
The entry/exit function can be activated or
canceled by pressing and holding the SET
switch for more than 10 seconds.
The indicator lights on the memory
switches (1 and 2) will blink once when
the function is canceled, and the indicator
lights will blink twice when the function is
activated. Note that the indicator lights
may illuminate after 5 seconds while
holding the SET switch. This indicates
readiness for linking the Intelligent Key to
a stored memory position. Keep the SET
switch pressed for more than 10 seconds
to turn on or off the entry/exit function.
The entry/exit function can also be acti-
vated or canceled if the “ Lift Steering
Wheel on Exit ” key or “ Slide Driver Seat
Pre-driving checks and adjustments
3-31AUTOMATIC DRIVE POSITIONER (if so
equipped)

Black plate (174,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-32 Pre-driving checks and adjustmentsBack on Exit ” key is turned to ON or OFF in
the “ Comfort ” settings. (See “ Vehicle
information and settings ” (P.4-9).)
Initialize entry/exit function GUID-0EEBBCEC-2899-4DC8-AE43-1CC42FE3C5C1
If the battery cable is disconnected, or if
the fuse opens, the entry/exit function will
not work though this function was set on
before. In such a case, after connecting the
battery or replacing with a new fuse, open
and close the driver ’ s door more than two
times after the ignition switch is turned
from the ON position to the LOCK position.
The entry/exit function will be activated. SPA2322
SEAT SYNCHRONIZATION FUNCTION GUID-44A9BCE7-C5A3-4DE5-84C7-DAFAF434BFA8
The seat synchronization function automa-
tically adjusts the positions of the steering
wheel and outside mirrors when the seat is
adjusted using the power seat switches.
However, the steering wheel and outside
mirrors will not move if the seat is adjusted
over the maximum thresholds. The system
considers that the steering wheel and
outside mirror adjustments are not neces-
sary because the seat may not be adjusted
for the driving position. Note that the
function is set to disabled as the factory
default setting. The seat synchronization function operates
under the following conditions:
. The ignition switch is in the ON posi-
tion.
. The selector lever is in the P (Park)
position (Automatic Transmission mod-
els) or the parking brake is applied
(Manual Transmission models).
. The seatback is raised (Coupe).
If the outside mirrors or the steering wheel
reaches its maximum adjustment, the
function is automatically disabled. Restart
the function by selecting a previously
stored seat memory position using the
memory switches (1 or 2). An Intelligent
Key that was previously linked to the
stored seat memory can also be used to
restart the function.
If a seat position was not previously stored
in the seat memory, restart the function by
adjusting the steering wheel and outside
mirrors manually for your best driving
position and then drive the vehicle above
4 MPH (7 km/h).

Black plate (175,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]Cancel or activate seat synchroni-
zation function GUID-9FA1381E-62FE-4338-8BE9-EF06F61AFC12
For Automatic Transmission models:
The selector lever must be in the P (Park)
position with the ignition switch in the ACC
position.
For Manual Transmission models:
The parking brake must be applied with
the ignition switch in the ACC position.
The seat synchronization function can be
activated or canceled by pushing and
holding the SET switch for more than 10
seconds while the ignition switch is in the
ACC position.
The indicator lights on the memory
switches (1 and 2) will blink once when
the function is canceled, and the indicator
lights will blink twice when the function is
activated. Note that the indicator lights
may illuminate after 5 seconds while
holding the SET switch. This indicates
readiness for linking the Intelligent Key to
a stored memory position. Keep the SET
switch pushed for more than 10 seconds to
turn on or off the seat synchronization
function. MEMORY STORAGE GUID-A3BE9A91-CE23-4574-92F2-3FB031E53D7E
Two positions for the driver ’ s seat, steering
column and outside mirrors can be stored
in the automatic drive positioner memory.
Follow these procedures to use the mem-
ory system.
1. Automatic transmission models:
Move the selector lever to the P (Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback (Coupe).
3. Push the ignition switch to the ON
position.
4. Adjust the driver ’ s seat, steering col-
umn and outside mirrors to the desired
positions by manually operating each
adjusting switch. For additional infor-
mation, see “ Seats ” (P.1-2) and “ Tilt/
telescopic steering ” (P.3-26) and “ Out-
side mirrors ” (P.3-29).
5. Push the SET switch and, within 5
seconds, push the memory switch (1
or 2) fully for at least 1 second.
The indicator light for the pushed
memory switch will stay on for approxi-
mately 5 seconds after pushing the switch.
If memory is stored in the same
memory switch, the previous memory
will be deleted.
Linking Intelligent Key to a stored
memory position GUID-260E8272-8777-4E19-9288-E40B723FABBA
The Intelligent Key can be linked to a
stored memory position with the following
procedure.
1. Follow the steps for storing a memory
position.
2. While the indicator light for the memory
switch being set is illuminated for 5
seconds, push the
button on the
Intelligent Key. If the indicator light
blinks, the Intelligent Key is linked to
that memory setting.
Push the ignition switch to the OFF posi-
tion, and then push the
button on the
Intelligent Key. The driver ’ s seat, steering
wheel and outside mirrors will move to the
memorized position.
Confirming memory storage GUID-E5D175B3-57DC-4C96-A449-0B72F25D2264
. Push the ignition switch to the ON
position and push the SET switch. If
the main memory has not been stored,
the indicator light will come on for
Pre-driving checks and adjustments
3-33

Black plate (176,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-34 Pre-driving checks and adjustmentsapproximately 0.5 second. When the
memory has stored in position, the
indicator light will stay on for approxi-
mately 5 seconds.
. If the battery cable is disconnected, or if
the fuse opens, the memory will be
canceled. In this case, reset the desired
position using the previous procedure.
. If optional Intelligent Keys are added to
your vehicle, the memory storage pro-
cedure to switch 1 or 2 and linking
Intelligent Key procedure to a stored
memory position should be performed
again for each Intelligent Key. For
additional Intelligent Key information,
see “ Keys ” (P.3-2).
Selecting the memorized position GUID-739A81F0-8862-49C2-BBA8-117F41F648F9
1. Automatic transmission models:
Move the selector lever to the P (Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback (Coupe).
3. Use one of the following methods to
move the driver ’ s seat, the outside
mirrors and the steering wheel. .
Push the ignition switch to the ON
position and push the memory
switch (1 or 2) fully for at least 1
second. .
Within 45 seconds of opening the
driver ’ s door, push the memory
switch (1 or 2) fully for at least 1
second.
The driver ’ s seat, steering column
and outside mirrors will move to the
memorized position with the indica-
tor light flashing, and then the light
will stay on for approximately 5
seconds.
For manual transmission models, the
memory positions can be selected even
when the engine is running. In this case,
move the shift lever to the N (Neutral)
position and apply the parking brake.
Then, perform step 2.
SYSTEM OPERATION GUID-0383C8BF-12F8-48D0-9B28-5A2A0DCC8D55
The automatic drive positioner system will
not work or will stop operating under the
following conditions:
. When the vehicle speed is above 4 MPH
(7 km/h).
. When the adjusting switch for the
driver ’ s seat and steering column is
turned on while the automatic drive positioner is operating.
. When the memory switch 1 or 2 is not
pushed for at least 1 second.
. When the seat, steering column and
outside mirrors have already been
moved to the memorized position.
. When no position is stored in the
memory switch.
. When the parking brake is released (MT
models).
. When the speed is above 4 MPH (7
km/h) while the parking brake is
applied (MT models).
To restart the drive positioner system,
move the parking brake to off and on.
. When the engine is started while
moving the automatic drive positioner.
. When the AT selector lever is moved
from the P (Park) position to any other
position. (However, it will not be
canceled if the switch is pushed while
the seat and steering column are
returning to the previous positions
(entry/exit function).)
. When the driver ’ s door remains open
for more than 45 seconds and the
ignition switch is not in the ON posi-
tion.

Black plate (177,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]. When the seatback is folded (Coupe).
. While the walk-in function operates
(Coupe).
. The seat synchronization function is
automatically disabled if the outside
mirrors or steering wheel reaches its
maximum adjustment.
. The seat synchronization function will
not operate if the seat is adjusted over
one of the following maximum thresh-
olds:
— Seat sliding: 3.0 in (76 mm)
— Seatback reclining: 9.1 degrees
— Seat lifter (rear side): 0.8 in (20 mm)
Pre-driving checks and adjustments
3-35