2012 INFINITI G37 reset

Black plate (105,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]amount of fuel in the fuel tank and the
actual fuel consumption.
The display is updated every 30 seconds.
The dte mode includes a low range warning
feature. If the fuel level is low, the warning
is displayed on the screen.
When the fuel level drops even lower, the
dte display will change to “——” .
. If the amount of fuel added is small, the
display just before the ignition switch
is pushed to the OFF position may
continue to be displayed.
. When driving uphill or rounding curves,
the fuel in the tank shifts, which may
momentarily change the display.
5. Outside air temperature (ICY — 8 F
or 8 C) GUID-35621BA5-D61E-4ECD-9628-F300D193449A
The outside air temperature is displayed in
8 F or 8 C in the range of − 22 to 131 8 F ( − 30
to 55 8 C).
The outside air temperature mode includes
a low temperature warning feature. If the
outside air temperature is below 37 8 F
(3 8 C), the warning is displayed on the
screen.
The outside temperature sensor is located
in front of the radiator. The sensor may be affected by road or engine heat, wind
directions and other driving conditions.
The display may differ from the actual
outside temperature or the temperature
displayed on various signs or billboards.
6. Setting GUID-9F18B5C6-F437-4D24-B240-415AA28B0E09
Setting cannot be made while driving. A
message “ Setting can only be operated
when stopped ” is also displayed on the
dot matrix crystal display.
The
switch
* A
and switch
* B
are
used in the setting mode to select and
decide a menu.
SKIP: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the switch
* A
to move to the
warning check mode.
Push the
switch
* B
to select other
menus.
ALERT: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
There are 3 submenus under the alert
menu.
. BACK
Select this submenu to return to the top
page of the setting mode.
. TIME TO REST
Select this submenu to specify when the “ time to rest ” indicator activates.
. ICY
Select this submenu to display the low
outside temperature warning.
MAINTENANCE: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
There are 5 submenus under the main-
tenance menu.
. BACK
Select this submenu to return to the top
page of the setting mode.
. ENGINE OIL
Select this submenu to set or reset the
distance for changing the engine oil.
. OIL FILTER
Select this submenu to set or reset the
distance for replacing the oil filter.
. TIRE
Select this submenu to set or reset the
distance for replacing tires.
. OTHER
Select this submenu and set or reset
the distance for replacing items other
than the engine oil, oil filter and tires.
DISPLAY: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
There are 3 submenus under the display
menu.
Instruments and controls
2-27

Black plate (167,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SPA2838
Coupe SPA2802
LOOSE FUEL CAP warning GUID-C419E1AB-BE96-4CEE-A3A0-A424103B7C58
The LOOSE FUEL CAP warning appears on
the dot matrix liquid crystal display when
the fuel-filler cap is not tightened correctly
after the vehicle has been refueled. It may
take a few driving trips for the message to
be displayed.
To turn off the warning, perform the
following:
1. Remove and install the fuel-filler cap as
soon as possible. (See “ Fuel-filler cap ”
(P.3-23).).
2. Tighten the fuel-filler cap until a single
click is heard. 3. Push the reset switch
* A
on the right
side of the combination meter panel for
about 1 second to turn off the LOOSE
FUEL CAP warning after tightening the
fuel cap.
Pre-driving checks and adjustments
3-25

Black plate (176,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-34 Pre-driving checks and adjustmentsapproximately 0.5 second. When the
memory has stored in position, the
indicator light will stay on for approxi-
mately 5 seconds.
. If the battery cable is disconnected, or if
the fuse opens, the memory will be
canceled. In this case, reset the desired
position using the previous procedure.
. If optional Intelligent Keys are added to
your vehicle, the memory storage pro-
cedure to switch 1 or 2 and linking
Intelligent Key procedure to a stored
memory position should be performed
again for each Intelligent Key. For
additional Intelligent Key information,
see “ Keys ” (P.3-2).
Selecting the memorized position GUID-739A81F0-8862-49C2-BBA8-117F41F648F9
1. Automatic transmission models:
Move the selector lever to the P (Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback (Coupe).
3. Use one of the following methods to
move the driver ’ s seat, the outside
mirrors and the steering wheel. .
Push the ignition switch to the ON
position and push the memory
switch (1 or 2) fully for at least 1
second. .
Within 45 seconds of opening the
driver ’ s door, push the memory
switch (1 or 2) fully for at least 1
second.
The driver ’ s seat, steering column
and outside mirrors will move to the
memorized position with the indica-
tor light flashing, and then the light
will stay on for approximately 5
seconds.
For manual transmission models, the
memory positions can be selected even
when the engine is running. In this case,
move the shift lever to the N (Neutral)
position and apply the parking brake.
Then, perform step 2.
SYSTEM OPERATION GUID-0383C8BF-12F8-48D0-9B28-5A2A0DCC8D55
The automatic drive positioner system will
not work or will stop operating under the
following conditions:
. When the vehicle speed is above 4 MPH
(7 km/h).
. When the adjusting switch for the
driver ’ s seat and steering column is
turned on while the automatic drive positioner is operating.
. When the memory switch 1 or 2 is not
pushed for at least 1 second.
. When the seat, steering column and
outside mirrors have already been
moved to the memorized position.
. When no position is stored in the
memory switch.
. When the parking brake is released (MT
models).
. When the speed is above 4 MPH (7
km/h) while the parking brake is
applied (MT models).
To restart the drive positioner system,
move the parking brake to off and on.
. When the engine is started while
moving the automatic drive positioner.
. When the AT selector lever is moved
from the P (Park) position to any other
position. (However, it will not be
canceled if the switch is pushed while
the seat and steering column are
returning to the previous positions
(entry/exit function).)
. When the driver ’ s door remains open
for more than 45 seconds and the
ignition switch is not in the ON posi-
tion.

Black plate (189,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]Fuel Economy information GUID-189D7485-90CC-4656-8551-1D08F50ECB7D
The approximate distance to empty, aver-
age fuel economy and current fuel econo-
my will be displayed for reference.
To reset the average fuel economy (Avg
Fuel Econ), select the “ Reset Fuel Eco ” or
“ Reset ” key.
If the “ Fuel Eco History ” or “ View ” key is
selected, the average fuel consumption
history will be displayed in graph form
along with the average for the previous
Reset-to-Reset period.
The unit can be converted between “ US ”
and “ Metric ” . (See “ How to use SETTING
button ” (P.4-14).)
The fuel economy information may differ
from the information displayed on the
vehicle information display. This is due to
the timing difference in updating the
information and does not indicate a mal-
function. SAA2481
SAA2482
Models with navigation system SAA2830
SAA2722
Models without navigation system
Monitor, climate, audio, phone and voice recognition systems
4-11

Black plate (190,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-12 Monitor, climate, audio, phone and voice recognition systemsMaintenance information GUID-6CA2CDFA-FC15-42AA-9EFD-CE037A72365B
The maintenance intervals can be dis-
played for the engine oil, oil filter, tire
and other reminders.
To set a maintenance interval, select a
preferred item from the list.
You can also set to display a message to
remind you that the maintenance needs to
be performed.
The following example shows how to set
the engine oil maintenance information.
Use the same steps to set the other
maintenance information.
1. Set the interval (mileage) of the main-
tenance schedule. To determine the
recommended maintenance interval,
refer to your “ INFINITI Service and
Maintenance Guide ” .
2. To display the reminder automatically
when the desired distance is reached,
select the “ Reminder ” key.
3. Reset the driving distance to the new
maintenance schedule.
4. To return to the previous screen, push
the BACK button.
The unit can be converted between “ US ”
and “ Metric ” . (See “ How to use SETTING button ” (P.4-14).)
SAA3003
Models with navigation system
SAA1611
Models without navigation system

Black plate (191,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]The Reminder will be automatically dis-
played when the specified distance has
been driven and every time the ignition
switch is pushed to the ACC or ON position.
The reminder will not appear while driving.
Select the “ OK ” key to hide the reminder
for the rest of the current drive.
To stop the reminder from appearing,
perform one of the following actions:
. Select the “ Reset Distance ” .
. Deactivate the “ Reminder ” .
. Increase the “ Interval ” distance to be
more than the current distance being
tracked. SAA2483
Others information (models with
navigation system) GUID-9F534085-BC7A-4AD1-8E18-3219FFD95CE9
The Others information display will appear
when pushing the INFO button and select-
ing the “ Others ” key.
GPS Position: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
For the details of this item, see the
separate Navigation System Owner ’ s Man-
ual.
Voice Recognition: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
For the details of this item, see “ INFINITI
Voice Recognition system (models with
navigation system) ” (P.4-114). SAA2484
Models with navigation system
SAA2604
Models without navigation system
Monitor, climate, audio, phone and voice recognition systems
4-13

Black plate (224,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-46 Monitor, climate, audio, phone and voice recognition systems. Some characters used in other lan-
guages (Chinese, Japanese, etc.) are
not displayed properly on the vehicle
center screen. Using English language
characters with a USB device is recom-
mended.
. Do not connect a USB device if a
connector or cable is wet. Allow the
cable and/or connectors to dry com-
pletely before connecting the USB
device. If the connector is exposed to
fluids other than water, evaporative
residue may cause a short between
the connector pins.
. Large video podcast files cause slow
responses in an iPod ®
. The vehicle
center display may momentarily black
out, but it will soon recover.
. If an iPod ®
automatically selects large
video podcast files while in the shuffle
mode, the vehicle center display may
momentarily black out, but it will soon
recover.
. Audiobooks may not play in the same
order as they appear on an iPod ®
.
. An iPod nano ®
(1st Generation) may
remain in fast forward or rewind mode
if it is connected during a seek opera-
tion. In this case, please manually reset the iPod ®
.
. An iPod nano ®
(2nd Generation) will
continue to fast forward or rewind if it
is disconnected during a seek opera-
tion.
. An incorrect song title may appear when
the Play Mode is changed while using
the iPod nano ®
(2nd Generation)
iPod ®
is a trademark of Apple Inc.,
registered in the U.S. and other countries.
Compressed Audio Files (MP3/
WMA/AAC) GUID-47EB1CBC-EA75-4271-9A35-A2D303CDA119
Explanation of terms: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
. MP3 — MP3 is short for Moving Pictures
Experts Group Audio Layer 3. MP3 is
the most well known compressed
digital audio file format. This format
allows for near “ CD quality ” sound, but
at a fraction of the size of normal audio
files. MP3 conversion of an audio track
can reduce the file size by approxi-
mately a 10:1 ratio (Sampling: 44.1
kHz, Bit rate: 128 kbps) with virtually
no perceptible loss in quality. The
compression reduces certain parts of
sound that seem inaudible to most
people. . WMA — Windows Media Audio (WMA) is
a compressed audio format created by
Microsoft as an alternative to MP3. The
WMA codec offers greater file compres-
sion than the MP3 codec, enabling
storage of more digital audio tracks in
the same amount of space when
compared to MP3s at the same level
of quality.
. AAC/M4A — Advanced Audio Coding
(AAC) is a lossy audio compression
format. Audio files that have been
encoded with AAC are generally smaller
in size and deliver a higher quality of
sound than MP3.
. Bit rate — Bit rate denotes the number
of bits per second used by a digital
music file. The size and quality of a
compressed digital audio file is deter-
mined by the bit rate used when
encoding the file.
. Sampling frequency — Sampling fre-
quency is the rate at which the samples
of a signal are converted from analog to
digital (A/D conversion) per second.
. Multisession — Multisession is one of
the methods for writing data to media.
Writing data once to the media is called
a single session, and writing more than

Black plate (233,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ] SAA2724
Type A
1. ON·OFF/VOLUME control knob
2. Radio SCAN (tuning) button
3. RDM (random) RPT (repeat) play but-
ton
4. Radio CAT (category)/REW (rewind)
button for SEEK/TRACK 5. Radio CAT (category)/FF (fast forward)
button for SEEK/TRACK
6. Radio tuning / MP3/WMA/AAC folder
selector / AUDIO control knob
7. CD EJECT button
8. Radio station preset buttons No satellite radio reception is available
unless an XM Satellite Radio subscription
is active.
The audio control buttons are also located
on the center multi-function control panel.
Monitor, climate, audio, phone and voice recognition systems
4-55