2012 INFINITI G37 hose

Black plate (94,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-16 Instruments and controlsWARNING. If the light does not illuminate with the
ignition switch pushed ON, have the
vehicle checked by an INFINITI retailer as
soon as possible.
. If the light illuminates while driving,
avoid sudden steering maneuvers or
abrupt braking, reduce vehicle speed,
pull off the road to a safe location and
stop the vehicle as soon as possible.
Driving with under-inflated tires may
permanently damage the tires and in-
crease the likelihood of tire failure.
Serious vehicle damage could occur
and may lead to an accident and could
result in serious personal injury. Check
the tire pressure for all four tires. Adjust
the tire pressure to the recommended
COLD tire pressure shown on the Tire
and Loading Information label to turn
the low tire pressure warning light OFF. If
the light still illuminates while driving
after adjusting the tire pressure, a tire
may be flat. If you have a flat tire,
replace it with a spare tire as soon as
possible. . When a spare tire is mounted or a wheel
is replaced, the TPMS will not function
and the low tire pressure warning light
will flash for approximately 1 minute.
The light will remain on after the 1
minute. Contact your INFINITI retailer as
soon as possible for tire replacement
and/or system resetting.
. Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
CAUTION . The TPMS is not a substitute for the
regular tire pressure check. Be sure to
check the tire pressure regularly.
. If the vehicle is being driven at speeds of
less than 16 MPH (25 km/h), the TPMS
may not operate correctly.
. Be sure to install the specified size of
tires to the four wheels correctly.
Master warning light GUID-BFD238A1-B056-42EA-B9A0-FCCF2B17501F
When the ignition switch is in the ON
position, the master warning light illumi- nates if any of the following are displayed
on the dot matrix liquid crystal display:
. No key warning
. Low fuel warning
. Low washer fluid warning
. Parking brake release warning
. Door/trunk open warning
. Loose fuel cap warning
. Check tire pressure warning
See “ Dot matrix liquid crystal display ” (P.2-
20).
Preview Function warning light
(orange; if so equipped) GUID-B4E486C7-1748-4EBD-A37A-79C9F389E7E0
The light comes on if there is a malfunction
in the Brake Assist (with Preview Function)
system.
If the warning light comes on, park the
vehicle in a safe place. Turn the engine off,
restart the engine, resume driving and set
the ICC system again.
If it is not possible to set the system or the
indicator stays on, it may indicate that the
system is malfunctioning. Although the
vehicle is still driveable under normal
conditions, have the vehicle checked at
an INFINITI retailer.

Black plate (140,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-62 Instruments and controlsPROGRAMMING TROUBLE-DIAGNO-
SIS GUID-D075D2BD-E7C7-474E-83FC-B6F733CCAE46
If HomeLink ®
does not quickly learn the
hand-held transmitter information:
. replace the hand-held transmitter bat-
teries with new batteries.
. position the hand-held transmitter with
its battery area facing away from the
HomeLink ®
surface.
. push and hold both the HomeLink ®
and
hand-held transmitter buttons without
interruption.
. position the hand-held transmitter 2 to
5 in (50 to 127 mm) away from the
HomeLink ®
surface. Hold the transmit-
ter in that position for up to 15
seconds. If HomeLink ®
is not pro-
grammed within that time, try holding
the transmitter in another position -
keeping the indicator light in view at all
times.
If you continue to have programming
difficulties, please contact the INFINITI
Consumer Affairs Department. The phone
numbers are located in the Foreword of
this Owner ’ s Manual. CLEARING THE PROGRAMMED IN-
FORMATION GUID-93441B3F-2212-4876-94D6-FC87E5157313
Individual buttons cannot be cleared,
however to clear all programming, push
and hold the two outside buttons and
release when the indicator light begins to
flash (in approximately 20 seconds).
REPROGRAMMING A SINGLE
HomeLink ®
BUTTON GUID-F8D4C203-F653-4BE8-9078-5A51BCCE5405
To reprogram a HomeLink ®
Universal
Transceiver button, complete the following.
1. Push and hold the desired HomeLink ®
button. Do not release the button until
step 4 has been completed.
2. When the indicator light begins to flash
slowly (after 20 seconds), position the
hand-held transmitter 2 to 5 in (50 to
127 mm) away from the HomeLink ®
surface.
3. Push and hold the hand-held transmit-
ter button.
4. The HomeLink ®
indicator light will
flash, first slowly and then rapidly.
When the indicator light begins to flash
rapidly, release both buttons.
The HomeLink ®
Universal Transceiver but-
ton has now been reprogrammed. The new device can be activated by pushing the
HomeLink ®
button that was just pro-
grammed. This procedure will not affect
any other programmed HomeLink ®
but-
tons.
IF YOUR VEHICLE IS STOLEN GUID-5786CF0E-BD69-4511-B9FA-84F26F89F025
If your vehicle is stolen, you should change
the codes of any non-rolling code device
that has been programmed into
HomeLink ®
. Consult the Owner ’ s Manual
of each device or call the manufacturer or
retailer of those devices for additional
information.
When your vehicle is recovered, you will
need to reprogram the HomeLink ®
Uni-
versal Transceiver with your new transmit-
ter information.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference that
may cause undesired operation.

Black plate (149,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]GUID-E775A3D7-CE8E-4FE0-9FB8-238232937EE5
WARNING. Radio waves could adversely affect
electric medical equipment. Those who
use a pacemaker should contact the
electric medical equipment manufacturer
for the possible influences before use.
. The Intelligent Key transmits radio
waves when the buttons are pushed.
The FAA advises that the radio waves
may affect aircraft navigation and com-
munication systems. Do not operate the
Intelligent Key while on an airplane.
Make sure the buttons are not operated
unintentionally when the unit is stored
during a flight.
The Intelligent Key system can operate all
the doors and the trunk lid using the
remote controller function or pushing the
request switch on the vehicle without
taking the key out from a pocket or purse.
The operating environment and/or condi-
tions may affect the Intelligent Key system
operation.
Be sure to read the following before using
the Intelligent Key system. CAUTION . Be sure to carry the Intelligent Key with
you when operating the vehicle.
. Never leave the Intelligent Key in the
vehicle when you leave the vehicle.
The Intelligent Key is always communicat-
ing with the vehicle as it receives radio
waves. The Intelligent Key system trans-
mits weak radio waves. Environmental
conditions may interfere with the operation
of the Intelligent Key system under the
following operating conditions.
. When operating near a location where
strong radio waves are transmitted,
such as a TV tower, power station and
broadcasting station.
. When in possession of wireless equip-
ment, such as a cellular telephone,
transceiver, and CB radio.
. When the Intelligent Key is in contact
with or covered by metallic materials.
. When any type of radio wave remote
control is used nearby.
. When the Intelligent Key is placed near
an electric appliance such as a perso- nal computer.
. When the vehicle is parked near a
parking meter.
In such cases, correct the operating condi-
tions before using the Intelligent Key
function or use the mechanical key.
Although the life of the battery varies
depending on the operating conditions,
the battery ’ s life is approximately 2 years.
If the battery is discharged, replace it with
a new one.
When the Intelligent Key battery is almost
discharged, insert the Intelligent Key into
the Intelligent Key port to start the engine.
Replace the discharged battery with a new
one as soon as possible. For more details,
see “ Push-button ignition switch ” (P.5-9).
Since the Intelligent Key is continuously
receiving radio waves, if the key is left near
equipment which transmits strong radio
waves, such as signals from a TV and
personal computer, the battery life may
become shorter.
For information regarding replacement of a
battery, see “ Intelligent Key battery repla-
cement ” (P.8-26).
As many as 4 Intelligent Keys can be
registered and used with one vehicle. For
Pre-driving checks and adjustments
3-7INTELLIGENT KEY SYSTEM

Black plate (183,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]HOW TO USE INFINITI CONTROLLER GUID-7A498997-935F-4751-B393-57B01CF46DDF
Choose an item on the display using the
main directional buttons
* 2
(or additional
directional buttons
* 6
with navigation
system) or center dial
* 3
, and push the
ENTER button
* 1
for operation.
If you push the BACK button
* 4
before the
setup is completed, the setup will be
canceled and/or the display will return to
the previous screen. This button can also
be used to delete characters that have
been input.
After the setup is completed, push the
BACK button
* 4
and return to the previous
screen.
For the VOICE button
* 5
functions, refer to
the separate Navigation System Owner ’ s
Manual.
HOW TO USE TOUCH SCREEN
(models with navigation system) GUID-6611C03E-CDBF-4D30-B540-4F9F66BCB2C5
CAUTION. The glass screen on the liquid crystal
display may break if it is hit with a hard
or sharp object. Do not touch the glass if
it breaks. Doing so could result in an injury.
. To clean the display, use a soft, dry
cloth. If additional cleaning is necessary,
use a small amount of neutral detergent
with a soft cloth. Never use a rough
cloth, alcohol, benzine, thinner or any
kind of solvent or paper towel with a
chemical cleaning agent. They will
scratch or deteriorate the panel.
. Do not splash any liquid such as water
or car fragrance on the display. Contact
with liquid will cause the system to
malfunction.
To ensure safe driving, some functions
cannot be operated while driving.
The on-screen functions that are not
available while driving will be “ grayed
out ” or muted.
Park the vehicle in a safe location and then
operate the navigation system.
WARNING . ALWAYS give your full attention to
driving.
. Avoid using vehicle features that could distract you. If distracted, you could lose
control of your vehicle and cause an
accident.
Touch screen operation GUID-9E906F90-D180-4427-8288-7815C56B83FB
With this system, the same operations as
those for the INFINITI controller are possi-
ble using the touch screen operation.
Monitor, climate, audio, phone and voice recognition systems
4-5

Black plate (207,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SAA2404
Models with navigation system
SAA2606
Models without navigation system PREDICTIVE COURSE LINE SETTINGS GUID-E2F40034-05E0-401F-9E99-A34483BA8B36
To turn ON or OFF the predictive course line
display, push the SETTING button, select
the “ Camera ” key and push the ENTER
button.
. Predictive Course Lines
When this item is turned to ON, the
predicted course lines will be displayed
on the monitor when the selector/shift
lever is in the “ R ” (Reverse) position.
HOW TO ADJUST SCREEN GUID-8EC63937-DDFF-48F5-9E13-CE42D28EBED6
To adjust the Display ON/OFF, Brightness,
Tint, Color, Contrast and Black Level of the
rearview monitor, push the SETTING button
with the rearview monitor on, select the
“ Display ” key on the screen and select the
item key and adjust the level using the
INFINITI controller.
Do not adjust the Brightness, Tint, Color,
Contrast and Black Level of the rearview
monitor while the vehicle is moving. Make
sure the parking brake is firmly applied
and the engine is not running. OPERATING TIPS GUID-C7806C41-88DD-4A7A-BEE4-AA3328E302E3
. When the selector/shift lever is shifted
to the “ R ” (Reverse) position, the
monitor screen automatically changes
to the rearview monitor mode. How-
ever, the radio can be heard.
. It may take some time until the rearview
monitor is displayed after the selector/
shift lever has been shifted to “ R ” from
another position or to another position
from “ R ” . Objects may be distorted
momentarily until the rearview monitor
screen is displayed completely.
. When the temperature is extremely high
or low, the screen may not clearly
display objects. This is not a malfunc-
tion.
. When strong light directly enters the
camera, objects may not be displayed
clearly. This is not a malfunction.
. Vertical lines may be seen in objects on
the screen. This is due to strong
reflected light from the bumper. This
is not a malfunction.
. The screen may flicker under fluores-
cent light. This is not a malfunction.
. The colors of objects on the rearview
monitor may differ somewhat from
those of the actual object.
Monitor, climate, audio, phone and voice recognition systems
4-29

Black plate (254,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-76 Monitor, climate, audio, phone and voice recognition systems. Second generation iPod touch ®
(version
1.2.3 or later)
. First generation iPod nano ®
(version
1.3.1 or later)
. Second generation iPod nano ®
(version
1.1.3 or later)
. Third generation iPod nano ®
(version
1.1 or later)
. Fourth generation iPod nano ®
(version
1.0.2 or later)
Models without navigation system: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
. Fifth generation iPod ®
(firmware ver-
sion 1.3)
. First generation iPod Classic ®
(firmware
version 1.1.2 PC)
. Second generation iPod Classic ®
(firm-
ware version 2.0 PC)
. First generation iPod touch ®
(firmware
version 2.1)
. Second generation iPod touch ®
(firm-
ware version 2.1.1)
. First generation iPod nano ®
(firmware
version 1.3.1)
. Second generation iPod nano ®
(firm-
ware version 1.1.3)
. Third generation iPod nano ®
(firmware
version 1.1 PC) . Third generation iPhone ®
(firmware
version 2.1)
Make sure that the iPod ®
version is
updated.
Audio main operation GUID-12FEF761-1E1C-44EA-A5B7-774957A975FE
Push the ignition switch to the ACC or ON
position. Then, push the DISC·AUX or DISC
button repeatedly to switch to the iPod ®
mode.
If the system has been turned off while the
iPod ®
was playing, pushing the ON·OFF
button will start the iPod ®
.
or PLAY: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the DISC·AUX or AUX button is
pushed with the system off and the iPod ®
connected, the system will turn on. If
another audio source is playing and the
iPod ®
is connected, push the DISC·AUX or
AUX button repeatedly until the center
display changes to the iPod ®
mode.
Interface: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The interface for iPod ®
operation shown on
the vehicle center display is similar to the
iPod ®
interface. Use the INFINITI controller
and the ENTER or BACK button to play the
iPod ®
with your favorite settings. The following items can be chosen from the
menu list screen. For further information
about each item, see the iPod ®
Owner ’ s
Manual.
. Now Playing
. Playlists
. Artists
. Albums
. Songs
. Podcasts
. Genres
. Composers
. Audiobooks
. Shuffle Songs
The following touch-panel buttons shown
on the screen are also available:
.
: returns to the previous screen.
. : plays/pauses the music selected.
Next/Previous Track and Fast
Forward/Rewind: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the or button is pushed for
more than 1.5 seconds while the iPod ®
is
playing, the iPod ®
will play while fast
forwarding or rewinding. When the button
is released, the iPod ®
will return to the
normal play speed.

Black plate (259,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SAA2516
Models with navigation system
SAA2725
Models without navigation system There are some options available by
selecting the “ Menu ” key on the screen
during playback. Select one of the follow-
ing options that are displayed on the
screen if necessary.
Now Playing (models with navigation
system): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Displays a track list to choose a preferred
track for playback.
Music Library: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
There are some options available during
playback. Select one of the following
options that are displayed on the screen
if necessary.
. Artists
Play tracks by an artist whose music is
currently being played. The artists are
sorted in alphabetical order.
. Albums
Play tracks in each album. The albums
are sorted in alphabetical order.
. All Songs
Play tracks from all recorded tracks. The
tracks are sorted in alphabetical order.
. Genres
Play tracks by a selected genre. My Playlists (models with navigation
system): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Displays the Playlist and edits the Playlist
if necessary.
Select the “ Edit ” key.
The following items are available
. Add Current Songs
Add a current track to the Playlist.
. Add Songs by Album
Displays a list of albums in alphabetical
order. Selecting an album displays all
of the tracks in the album. Select tracks
from the list to add to the Playlist.
. Add Songs by Artist
Displays a list of artists in alphabetical
order. Selecting an artist displays all of
the tracks by the artist. Select tracks
from the list to add to the Playlist.
. Edit Songs Order
Reorder the tracks in the Playlist by
selecting a track and specifying the
order.
. Edit Name
Edit the name of the Playlist using the
keypad displayed on the screen. (See
“ How to use INFINITI controller ” (P.4-5).)
Monitor, climate, audio, phone and voice recognition systems
4-81

Black plate (297,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SAA2535
2. A list of commands appears on the
screen, and the system announces,
“ Would you like to access Phone,
Navigation, Information, Audio or
Help? ” .
3. After the tone sounds and the icon on
the screen changes from
to ,
speak a command.
Selecting the “ Practice ” key will start
the practice mode. See “ Let ’ s Practice ”
(P.4-117).
4. Continue to follow the voice menu
prompts and speak after the tone
sounds until your desired operation is
completed. Selecting the “ Help ” key can display
the detailed information of the each
command.
Operating tips: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
. Say a command after the tone.
. Commands that are available are al-
ways shown on the display and spoken
through voice menu prompts. Com-
mands other than those that are dis-
played are not accepted. Please follow
the prompts given by the system.
. If the command is not recognized, the
system announces, “ Please say again ” .
Repeat the command in a clear voice.
. Push the BACK button once to return to
the previous screen.
. To exit the voice recognition system,
push and hold the TALK
switch. The
message, “ Voice canceled ” will be
announced.
. To skip the voice guidance function and
give the command immediately, press
the TALK
switch to interrupt the
system. Remember to speak after the
tone.
. If you want to adjust the volume of the
system feedback, push the volume
control buttons [+] or [ − ] on the steering switch or use the audio system
volume knob while the system is
making an announcement.
How to speak numbers: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
INFINITI Voice Recognition requires a cer-
tain way to speak numbers when giving
voice commands. Refer to the following
examples.
General rule
Only single digits 0 (zero) to 9 can be used.
(For example, if you would like to say 500,
“ five zero zero ” can be used, but “ five
hundred ” cannot.)
Examples
. 1-800-662-6200
— “ One eight zero zero six six two six
two zero zero ”
Improving Recognition of Phone numbers
You can improve the recognition of phone
numbers by saying the phone number in
three groups of numbers. For example,
when you try to call 800-662-6200, say
“ eight zero zero ” first, and the system will
then ask you for the next three digits. Then,
say “ six six two ” . After recognition, the
system will then ask for the last four digits.
Say, “ six two zero zero ” . Using this method
Monitor, climate, audio, phone and voice recognition systems
4-119