2012 INFINITI G37 fog light

Black plate (112,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-34 Instruments and controls GUID-226BF3DF-6B81-4996-83A4-AFAA9459A0FA
SIC3239
Type A
SIC3278
Type B To defog/defrost the rear window glass
and outside mirrors (if so equipped), start
the engine and push the switch
* 1
on. The
indicator light
* 2
will come on. Push the
switch again to turn the defroster off.
It will automatically turn off in approxi-
mately 15 minutes.
CAUTION When cleaning the inner side of the rear
window, be careful not to scratch or damage
the rear window defroster. GUID-5792C62E-7176-49E9-912A-E3EBBEA0508B
XENON HEADLIGHTS GUID-8467C3F9-1393-492A-B09D-23AF70810C36
WARNING HIGH VOLTAGE
. When xenon headlights are on, they
produce a high voltage. To prevent an
electric shock, never attempt to modify
or disassemble. Always have your xenon
headlights replaced at an INFINITI retai-
ler.
. Xenon headlights provide considerably
more light than conventional headlights.
If they are not correctly aimed, they
might temporarily blind an oncoming
driver or the driver ahead of you and
cause a serious accident. If headlights
are not aimed correctly, immediately
take your vehicle to an INFINITI retailer
and have the headlights adjusted cor-
rectly.
When the xenon headlight is initially
turned on, its brightness or color varies
slightly. However, the color and brightness
will soon stabilize.
. The life of xenon headlights will be
shortened by frequent on-off operation.REAR WINDOW AND OUTSIDE MIRROR
DEFROSTER SWITCH HEADLIGHT AND TURN SIGNAL SWITCH

Black plate (117,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SIC3272
FOG LIGHT SWITCH GUID-782C350F-DF92-4D39-BD90-4155E2E5F990
To turn the fog lights on, turn the headlight
switch to the
position, then turn the
switch to the
position. To turn them
off, turn the switch to the OFF position.
The headlights must be on for the fog
lights to operate. GUID-6A8C64A7-6F2F-477B-8944-B7474460FBD5
SIC2574
Push the switch on to warn other drivers
when you must stop or park under
emergency conditions. All turn signal lights
will flash.
WARNING . If stopping for an emergency, be sure to
move the vehicle well off the road.
. Do not use the hazard warning flashers
while moving on the highway unless
unusual circumstances force you to drive
so slowly that your vehicle might be-
come a hazard to other traffic. . Turn signals do not work when the
hazard warning flasher lights are on.
The flasher can be actuated with the
ignition switch in any position.
Some state laws may prohibit the use of
the hazard warning flasher switch while
driving.
Instruments and controls
2-39HAZARD WARNING FLASHER SWITCH

Black plate (211,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4. To turn off the climate control system,
push the “ OFF ” button.
A visible mist may be seen coming from the
ventilators in hot, humid conditions as the
air is cooled rapidly. This does not indicate
a malfunction.
Heating (A/C OFF): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The air conditioner does not activate in this
mode. When you need to heat only, use
this mode.
1. Push the “ AUTO ” button on.
2. Push the “ A/C ” button. (The A/C
indicator will turn off.)
3. Turn the temperature control dial to set
the desired temperature.
. The temperature of the passenger
compartment will be maintained auto-
matically. Air flow distribution and fan
speed are also controlled automati-
cally.
. Do not set the temperature lower than
the outside air temperature. Otherwise
the system may not work properly.
. Not recommended if windows fog up.
Dehumidified defrosting or defogging: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
1. Push the “ ” front defroster button.
(The indicator light on the button will come on.)
2. Turn the temperature control dial to set
the desired temperature.
. To quickly remove ice from the outside
of the windows, push the fan speed
increase button “
” and set it to the
maximum position.
. As soon as possible after the wind-
shield is clean, push the “ AUTO ” button
to return to the auto mode.
. When the “
” front defroster button
is pushed, the air conditioner will
automatically be turned on at outside
temperatures above 23 8 F ( − 5 8 C) to
defog the windshield, and the air
recirculate mode will automatically be
turned off.
Outside air is drawn into the passenger
compartment to improve the defogging
performance.
Manual operation GUID-229B673E-2AED-4344-9C09-630604A66426
Fan speed control: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the fan speed increase “ ” or
decrease “
” buttons to manually con-
trol the fan speed.
Push the “ AUTO ” button to return to
automatic control of the fan speed. Air recirculation: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the intake air control button “
” to recirculate interior air inside the
vehicle. The indicator light on the “
”
side will come on.
The air recirculation mode cannot be
activated when the air conditioner is in
the front defrosting mode “
” .
Outside air circulation: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the intake air control button “
” to draw outside air into the passen-
ger compartment. The indicator light on the
“
” side will come on.
Automatic intake air control: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
In the AUTO mode, the intake air will be
controlled automatically. To manually con-
trol the intake air, push the intake air
control button “
” . To return to the
automatic control mode, push the intake
air control button “
” for about 2
seconds. The indicator lights (both air
recirculation and outside air circulation
sides) will flash twice, and then the intake
air will be controlled automatically.
Monitor, climate, audio, phone and voice recognition systems
4-33

Black plate (213,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2. Use the temperature control dial to set
the desired temperature. .
The temperature can be set within
the following range.
— For U.S.: 60 to 90 8 F (16 to 32 8 C)
— For Canada: 64 to 90 8 F (18 to
32 8 C) .
The temperature of the passenger
compartment will be maintained
automatically. Air flow distribution
and fan speed will also be controlled
automatically.
3. To turn off the climate control system,
push the “ OFF ” button.
A visible mist may be seen coming from the
ventilators in hot, humid conditions as the
air is cooled rapidly. This does not indicate
a malfunction.
Heating (A/C OFF): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The air conditioner does not activate in this
mode. When you need to heat only, use
this mode.
1. Push the “ AUTO ” button on.
2. Push the “ A/C ” button. (The A/C
indicator will turn off.)
3. Turn the temperature control dial to set
the desired temperature. . The temperature of the passenger
compartment will be maintained auto-
matically. Air flow distribution and fan
speed are also controlled automati-
cally.
. Do not set the temperature lower than
the outside air temperature. Otherwise
the system may not work properly.
. Not recommended if windows fog up.
Dehumidified defrosting or defogging: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
1. Push the “ ” front defroster button.
(The indicator light on the button will
come on.)
2. Turn the temperature control dial to set
the desired temperature.
. To quickly remove ice from the outside
of the windows, turn the “
” fan
speed control dial and set it to the
maximum position.
. As soon as possible after the wind-
shield is clean, push the “ AUTO ” button
to return to the auto mode.
. When the “
” front defroster button
is pushed, the air conditioner will
automatically be turned on at outside
temperatures above 23 8 F ( − 5 8 C) to
defog the windshield, and the air
recirculate mode will automatically be turned off.
Outside air is drawn into the passenger
compartment to improve the defogging
performance.
Manual operation GUID-1366819E-B7B2-452E-BFAE-A3526FCA00F5
Fan speed control: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Turn the “ ” fan speed control dial to
manually control the fan speed.
Push the “ AUTO ” button to return to
automatic control of the fan speed.
Air recirculation: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the intake air control button “
” to recirculate interior air inside the
vehicle. The indicator light on the “ ”
side will come on.
The air recirculation mode cannot be
activated when the air conditioner is in
the front defrosting mode “
” .
Outside air circulation: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the intake air control button “
” to draw outside air into the passen-
ger compartment. The indicator light on the
“
” side will come on.
Automatic intake air control: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
In the AUTO mode, the intake air will be
controlled automatically. To manually con-
Monitor, climate, audio, phone and voice recognition systems
4-35

Black plate (216,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-38 Monitor, climate, audio, phone and voice recognition systems .
To cancel the separate temperature
setting, push the “ DUAL ” button, the
indicator light turns off, and the
driver ’ s side temperature setting will
be applied to both the driver ’ s and
front passenger ’ s sides..
Do not set the temperature lower
than the outside air temperature.
Doing so may cause the temperature
not to be controlled properly. .
If the windows fog up, use dehumi-
dified heating instead of the A/C off
heating.
Dehumidified defrosting/defogging: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
1. Push the “ ” button. (The indicator
light will illuminate.)
2. Turn the temperature control dial to set
the desired temperature. .
To remove frost from the outside
surface of the windshield quickly,
set the temperature control and fan
speed control to their maximum
position. .
After the windshield is cleared, push
the “ AUTO ” button to set to the
automatic mode. .
When the “ ” button is pushed,
the air conditioner will automatically
turn on when the outside air tem- perature is above 23 8 F ( − 5 8 C) to
defog the windshield. The air recir-
culation mode will automatically
turn off. The outside air circulation
mode will be selected to improve the
defogging performance.
Manual operation GUID-B54CEF74-5525-417B-9446-684CEEF2F4C5
The manual mode can be used to control
the heater and air conditioner to your
desired settings.
To turn off the heater and air conditioner,
push the “ OFF ” button.
Fan speed control: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the fan speed control button “ ” to
increase the fan speed.
Push the fan speed control button “
” to
decrease the fan speed.
Push the “ AUTO ” button to change the fan
speed to the automatic mode.
Air flow control: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the “ MODE ” button to change the air
flow mode. : Air flows from the center and side ventilators.
: Air flows from the center and side ventilators,
and foot outlets.
: Air flows mainly from the foot outlets. : Air flows from the defroster and foot outlets.
Temperature control: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Turn the temperature control dial to set the
desired temperature.
. The temperature can be set within the
following range.
— For U.S.: 60 to 90 8 F (16 to 32 8 C)
— For Canada: 64 to 90 8 F (18 to 32 8 C)
Air recirculation: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the intake air control button to
recirculate interior air inside the vehicle.
The indicator light on the “
” side will
illuminate.
The air recirculation mode cannot be
activated when the air conditioner is in
the front defrosting mode “
” .
Outside air circulation: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the intake air control button to draw
outside air into the passenger compart-
ment.
The indicator light on the “
” side and
“
” side will turn off.
Automatic intake air control: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
In the AUTO mode, the intake air will be
controlled automatically. To manually con-
trol the intake air, push the intake air

Black plate (346,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]5-26 Starting and drivingsary.
The detection range of the sensor is
approximately 390 ft (120 m) ahead.
WARNING. This system is only an aid to assist the
driver and is not a collision warning or
avoidance device. It is the driver ’ s
responsibility to stay alert, drive safely
and be in control of the vehicle at all
times.
. The system is primarily intended for use
on straight, dry, open roads with light
traffic. It is not advisable to use the
system in city traffic or congested areas.
. This system will not adapt automatically
to road conditions. This system should
be used in evenly flowing traffic. Do not
use the system on roads with sharp
curves, or on icy roads, in heavy rain or
in fog.
The distance sensor will not detect under
most conditions:
. Stationary and slow moving vehicles
. Pedestrians or objects in the roadway . Oncoming vehicles in the same lane
. Motorcycles traveling offset in the travel
lane
This system will not automatically brake
the vehicle to a stop.
WARNING . As there is a performance limit to the
distance control function, never rely
solely on the Intelligent Cruise Control
system. This system does not correct
careless, inattentive or absent-minded
driving, or overcome poor visibility in
rain, fog, or other bad weather. Decele-
rate the vehicle speed by depressing the
brake pedal, depending on the distance
to the vehicle ahead and the surround-
ing circumstances in order to maintain a
safe distance between vehicles.
. Although the brake operation is con-
trolled by the system, the system does
not automatically stop the vehicle. If the
vehicle speed falls below approximately
20 MPH (32 km/h), the Intelligent Cruise
Control system is automatically canceled
and a warning chime sounds. (The brake
control is also canceled.) . The system may not detect the vehicle in
front of you in certain road or weather
conditions. To avoid accidents, never use
the Intelligent Cruise Control system
under the following conditions:
— On roads where the traffic is heavy
or there are sharp curves
— On slippery road surfaces such as
on ice or snow, etc.
— During bad weather (rain, fog, snow,
etc.)
When the windshield wiper is oper-
ated at the low speed (LO) or high
speed (HI) position, the Intelligent
Cruise Control system is automati-
cally canceled.
— When strong light (for example, at
sunrise or sunset) is directly shining
on the front of the vehicle
— When rain, snow or dirt adhere to
the system sensor
— On steep downhill roads (the vehi-
cle may go beyond the set vehicle
speed and frequent braking may
result in overheating the brakes)
— On repeated uphill and downhill

Black plate (373,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]all times.
. As there is a performance limit to the
Preview Function, never rely solely on
this system. This system does not
correct careless inattentive or absent-
minded driving, or overcome poor visi-
bility in rain, fog, or other bad weather.
Reduce vehicle speed by depressing the
brake pedal, in order to maintain a safe
distance between vehicles.
. The system may not detect the vehicle in
front of you in certain road or weather
conditions. The Preview Function may
not operate properly under the following
conditions. The vehicle is still driveable
under normal conditions and the Brake
Assist will operate.
— When rain, snow or dirt adhere to
the system sensor
— When strong light (for example, at
sunrise or sunset) is directly shining
on the front of the vehicle
— Winding or hilly roads may cause
the sensor to temporarily not detect
a vehicle in the same lane or may
detect objects or vehicles in other
lanes. — Vehicle position in the lane may
cause the sensor to temporarily not
detect a vehicle in the same lane or
may detect objects or vehicles in
other lanes.
SSD0471
Warning light and display GUID-A2927947-1E33-4EB3-9D1D-6799F67E6AB2
When the Preview Function is not operating
properly, a chime sounds and the system
warning light (orange) will come on.
Action to take: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
If the warning light comes on, park the
vehicle in a safe place. Turn the engine off,
restart the engine and resume driving.
If the indicator stays on, it may indicate
that the Preview Function is malfunction-
ing (the brake is operative). Although the
Vehicle is still driveable under normal
conditions, have the vehicle checked at
an INFINITI retailer.
Starting and driving
5-53

Black plate (434,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]8-28 Maintenance and do-it-yourself GUID-CC43F1E0-CD84-4C89-AE76-E3BF74F58A31
JVM0099XSEDAN GUID-DC499FCB-C993-49FE-B186-4299E70AF763
1. Front turn signal light and parking
light
2. Headlight (high- and low-beam)
3. Front side marker light
4. Map light
5. Rear personal light
6. Fog light
7. Step light
8. Trunk light
9. High-mounted stop light
10. License plate light
11. Back-up light
12. Rear combination light (rear turn
signal/tail/stop/side marker light)LIGHTS