2012 Hyundai Elantra fog light bulb

Maintenance
58
7
LIGHT BULBS
Use only the bulbs of the specified
wattage.
All bulbs are available from yourHYUNDAI dealers Parts Department.
✽✽ NOTICE
After heavy, driving rain or washing,
headlight and taillight lenses could
appear frosty. This condition is caused by
the temperature difference between the
lamp inside and outside. This is similar
to the condensation on your windows
inside your vehicle during the rain and
doesn’t indicate a problem with your
vehicle. If the water leaks into the lamp
bulb circuitry, have the vehicle checked
by an authorised HYUNDAI dealer.
Headlight, position light, turn sig-
nal light, front fog light bulbreplacement
(1) Headlight (High) / Position light
(2) Headlight (Low)
(3) Front turn signal light(4) Dedicated lamp (DRL) (if equipped)
(5) Front fog light (if equipped)
WARNING - Working on
the lights
Prior to working on the light, firmly
apply the parking brake, ensure
that the ignition switch is turned tothe LOCK position and turn off the
lights to avoid sudden movement
of the vehicle and burning your fin-
gers or receiving an electric shock.
CAUTION
Be sure to replace the burned-out bulb with one of the same wattage
rating. Otherwise, it may causedamage to the fuse or electricwiring system.
CAUTION
If you don’t have necessary tools,the correct bulbs and the expertise,
consult an authorised HYUNDAIdealer. In many cases, it is difficultto replace vehicle light bulbs because other parts of the vehicle
must be removed before you canget to the bulb. This is especiallytrue if you have to remove the head-
light assembly to
get to the bulb(s).
Removing/installingthe headlight
assembly can result in damage to the vehicle.OMD070026
CAUTION
The headlight aiming adjustment may be necessary after the head-light assembly is reinstalled. If youare unsure how to replace or aim
the headlight, consult an autho-rised HYUNDAI dealer.

761
Maintenance
Front turn signal bulb
Follow steps 1 to 4 from previous page.
5. Remove the socket from the assemblyby turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
6. Remove the bulb from the socket by
pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket. Pull
the bulb out of the socket.
7. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place. 8. Install the socket in the assembly by
aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
9. Reinstall the light assembly to the body of the vehicle.
Front fog light and Dedicated light
(if equipped)
1. Disconnect the negative battery cable.
2. Remove the screws under the front bumper.
3. Disconnect the power connector from the socket.
OMD071058LOMD071056L
Turn signal

Maintenance
62
7
Front fog light (if equipped)
4. Remove the bulb-socket from the
housing by turning the socket counter
clockwise until the tabs on the socketalign with the slots on the housing. 5. Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the socket. Dedicated light (if equipped)
Follow steps 1 to 3 from previous page.
4. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
5. Remove the bulb by pulling it out.
6. Insert a new bulb by inserting it into the socket.
7. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
OMD071059L
OMD071060L
■
Type A
■ Type B
Front fog light
Front fog light
Dedicated lamp

Maintenance
64
7
Aiming point
H1 : Height between the head lamp bulb centre and ground (Low beam) H2 : Height between the head lamp bulb centre and ground (High beam)H3 : Height between the fog lamp bulb centre and groundW1 : Distance between the two head lamp bulbs centres (Low beam)W2 : Distance between the two head lamp bulbs centres (High beam)W3 : Distance between the two fo
g lamp bulbs centres
W2
H1 H2 H3
W1 W3
Screen
Ground< Distance between lamps >
< Ground Height >
Vehicle condition H1 H2 H3
W1 W2 W3
with DRL* without DRL* with DRL* without DRL*
Without driver 713 (28.1) 666 (26.2) 389 (15.3) 414 (16.3) 1,334 (52.5) 1,100 (43.3) 1400 (55.1) 1460 (57.5)
With driver 706 (27.8) 659 (25.9) 382 (15.0) 407 (16) 1,334 (52.5) 1,140 (44.9) 1400 (55.1) 1460 (57.5)
DRL : Daytime Running Light Unit: mm (in)

Maintenance
68
7
Side repeater light bulb replace- ment (if equipped)
If the light bulb is not operating, have the
vehicle checked by an authorised
HYUNDAI dealer. Rear combination light bulb replacement
(1) Rear fog light (if equipped)
(2) Back-up light
(3) Tail light
(4) Rear turn signal light(5) Stop / tail lightOutside light
1. Open the boot lid.
2. Remove the service cover by pulling out
the service cover.
OMD070032OMD071031LOMD070030

Maintenance
70
7
Inside light
1. Open the boot.
2. Loosen the retaining screw of the boot
lid cover and then remove the cover.
3. Disconnect the connector and then remove the nuts by turning the nuts
counter clockwise. Back up light
1. Take the light assembly out.
2. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
3. Remove the bulb by pulling it out. 4. Insert a new bulb by inserting it into the
socket.
5. Install the light assembly to the boot.
6. Reinstall the nuts and connector and then the boot lid cover by pushing in
the screw.
Rear fog light (if equipped)
4. Remove the socket from the assembly by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
5. Remove the bulb from the socket by pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket. Pull
the bulb out of the socket.
6. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
7. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
OMD070037
OMD070038
OMD070039
OMD070040
Rear fog light (if equipped)
Back up light

Specifications & Consumer information
2
8
ENGINE DIMENSIONS BULB WATTAGE
* : If equipped
Item
1.8 Engine
Displacement cc (cu. in) 1797 (109.66)
Bore x Stroke mm (in.)81x87.2 (3.19x3.43)
Firing order 1-3-4-2
No. of cylinders 4, In-line
Item mm (in)
Overall length 4530 (178.3)
Overall width 1775 (69.9)
Overall height 1445 (56.9)
Front tread 1563 (61.5)* 1
/ 1549 (61.0)* 2
/ 1551 (61.1)* 3
Rear tread1576 (62.0)*1
/ 1562 (61.5)* 2
/ 1564 (61.6)* 3
Wheelbase2700 (106.3)
Light BulbWattageBulb type
Headlights (Low)55H7
Headlights (High)55H1
Front turn signal light28PY21W
Position lights5W5W
Side repeater lightsLED-
Front fog lights*27H27W
Stop / tail lights21/5PY21/5W
Tail light 5W5W
Rear turn signal lights 21PY21W
Rear fog lights21H21W
Back-up lights16W16W
High mounted stop light21P21W
License plate lights5W5W
Map lamps8FASTON 8W
Room lamps8FASTON 8W
Luggage lamp*5FASTON 5W
*1
: with R15 tyre
* 2
: with R16 tyre
* 3
: with R17 tyre