2012 Hyundai Elantra light

Maintenance
48
7
Instrument panel fuse replace- ment
1. Turn the ignition switch and all other
switches off.
2. Open the fuse panel cover. 3. Pull the suspected fuse straight out.
Use the removal tool provided in the
engine compartment fuse panel.
4. Check the removed fuse; replace it if it is blown.
5. Push in a new fuse of the same rating, and make sure it fits tightly in the clips.
If it fits loosely, consult an authorised
HYUNDAI dealer.
If you do not have a spare, use a fuse of the same rating from a circuit you maynot need for operating the vehicle, such
as the cigarette lighter fuse.
If the electrical components do not work
and the fuses are OK, check the fuse
panel in the engine compartment. If a
fuse is blown, it must be replaced.
OMD071017ROMD070018

Maintenance
52
7
Inner fuse panel
Fuse NameSymbolFuse ratingProtected Component
START7.5AW/O Smart Key : ICM Relay Box (Burglar Alarm Relay)
With Smart Key : A/T - Transaxle Range Switch,
M/T - ECM, E/R Fuse & Relay Box (RLY.5), Smart Key Control Module
A/BAG15ASRS Control Module
A/BAG IND7.5AInstrument Cluster
MDPS7.5AEPS Control Module
POWER OUTLET FRT15APower Outlet
BCM7.5ASmart Key Control Module, BCM
A/CON SW7.5AA/C Control Module
MODULE 27.5AElectro Chromic Mirror, ESP (or ESC) OFF Switch
SPARE 110A-
MODULE 47.5ARear Parking Assist Sensor LH/RH (IN), Rear Parking Assist, Sensor LH/RH (OUT),
Head Lamp Levelling Device Switch, Head Lamp Levelling Device Actuator LH/RH,
A/C Control Module(Auto A/C)
IG120AE/R Fuse & Relay Box(FUSE - F9, F10, F11, F12, F13)
PDM 37.5ASmart Key Control Module
C/LIGHTER20ACigarette Lighter
MODULE 610APower Outside Mirror Switch, Audio, Digital Clock

Maintenance
54
7
Fuse NameSymbolFuse ratingProtected Component
P/WDW RH25AP/WDW RH Relay, Driver Safety Power Window Module(RHD)
PDM 27.5ASmart Key Control Module, Start Stop Button Switch
FOG LP RR10AICM Relay Box(Rear Fog Lamp Relay)
WIPER FRT25AICM Relay Box(Rain Sensor Relay), Multifunction Switch, E/R Fuse & Relay Box(RLY.2), Wiper Motor
MODULE 57.5ACluster Ionizer, Rain Sensor, Sunroof
MULTIMEDIA 27.5A-
AMP 125A-
PDM 125ASmart Key Control Module
SPARE 520A-
A/CON7.5AE/R Fuse & Relay Box(RLY.10), A/C Control Module
MEMORY10ABCM, Auto Light & Photo Sensor, Instrument Cluster, Data Link Connector,
Smart Jucntion Box Upgrade Connector, A/C Control Module, Digital Clock
P/WDW LH25AP/WDW LH Relay, Driver Safety Power Window Module(LHD)
DR LOCK20ADoor Lock Relay, Door Unlock Relay
P/SEAT DRV30ADriver Seat Manual Switch

Maintenance
58
7
LIGHT BULBS
Use only the bulbs of the specified
wattage.
All bulbs are available from yourHYUNDAI dealers Parts Department.
✽✽ NOTICE
After heavy, driving rain or washing,
headlight and taillight lenses could
appear frosty. This condition is caused by
the temperature difference between the
lamp inside and outside. This is similar
to the condensation on your windows
inside your vehicle during the rain and
doesn’t indicate a problem with your
vehicle. If the water leaks into the lamp
bulb circuitry, have the vehicle checked
by an authorised HYUNDAI dealer.
Headlight, position light, turn sig-
nal light, front fog light bulbreplacement
(1) Headlight (High) / Position light
(2) Headlight (Low)
(3) Front turn signal light(4) Dedicated lamp (DRL) (if equipped)
(5) Front fog light (if equipped)
WARNING - Working on
the lights
Prior to working on the light, firmly
apply the parking brake, ensure
that the ignition switch is turned tothe LOCK position and turn off the
lights to avoid sudden movement
of the vehicle and burning your fin-
gers or receiving an electric shock.
CAUTION
Be sure to replace the burned-out bulb with one of the same wattage
rating. Otherwise, it may causedamage to the fuse or electricwiring system.
CAUTION
If you don’t have necessary tools,the correct bulbs and the expertise,
consult an authorised HYUNDAIdealer. In many cases, it is difficultto replace vehicle light bulbs because other parts of the vehicle
must be removed before you canget to the bulb. This is especiallytrue if you have to remove the head-
light assembly to
get to the bulb(s).
Removing/installingthe headlight
assembly can result in damage to the vehicle.OMD070026
CAUTION
The headlight aiming adjustment may be necessary after the head-light assembly is reinstalled. If youare unsure how to replace or aim
the headlight, consult an autho-rised HYUNDAI dealer.

759
Maintenance
1. Open the bonnet.
2. Disconnect the negative battery cable.
3. Loosen the retaining bolts and removethe headlight assembly from the body
of the vehicle. If you can reach to the
bulb without removing the headlight
assembly, you don’t need to do step 3.
4. Disconnect the power connector(s) from the back of the headlight assem-
bly.
(Continued)
If a bulb becomes damaged orcracked, replace it immediately
and carefully dispose of it.
Wear eye protection when chang- ing a bulb. Allow the bulb to cool
down before handling it.
WARNING - Halogen bulbs
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
Always handle them carefully, and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact with liquids. Never touchthe glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated onlywhen installed in a headlight.
(Continued)
OHD076046OMD070027N

Maintenance
60
7
Headlight bulb (low, high)
5. Remove the headlight bulb cover by
turning it counterclockwise.
6. Disconnect the headlight bulb socket- connector.
7. Unsnap the headlight bulb retaining wire by depressing the end and push-
ing it upward.
8. Remove the bulb from the headlight assembly.
9. Install a new headlight bulb and snap the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
10. Connect the headlight bulb socket- connector.
11. Install the headlight bulb cover by turning it clockwise. ❈
❈
Traffic Change (For Europe)
The low beam light distribution is asym-
metric. If you go abroad to a country with
opposite traffic direction, this asymmetric
part will dazzle oncoming car driver. To
prevent dazzle, ECE regulation demand
several technical solutions (ex. automatic
change system, adhesive sheet, down
aiming). This headlamps are designed
not to dazzle opposite drivers. So, you
need not change your headlamps in a
country with opposite traffic direction.
Position light
Follow steps 1 to 4 from previous page.
5. Remove the socket and bulb by pulling it out.
6. Install a new bulb into the socket and insert the socket.
7. Reinstall the light assembly to the body of the vehicle.
OMD071028LOMD071062L
Low
HIghPosition

761
Maintenance
Front turn signal bulb
Follow steps 1 to 4 from previous page.
5. Remove the socket from the assemblyby turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
6. Remove the bulb from the socket by
pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket. Pull
the bulb out of the socket.
7. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place. 8. Install the socket in the assembly by
aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
9. Reinstall the light assembly to the body of the vehicle.
Front fog light and Dedicated light
(if equipped)
1. Disconnect the negative battery cable.
2. Remove the screws under the front bumper.
3. Disconnect the power connector from the socket.
OMD071058LOMD071056L
Turn signal

Maintenance
62
7
Front fog light (if equipped)
4. Remove the bulb-socket from the
housing by turning the socket counter
clockwise until the tabs on the socketalign with the slots on the housing. 5. Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the socket. Dedicated light (if equipped)
Follow steps 1 to 3 from previous page.
4. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
5. Remove the bulb by pulling it out.
6. Insert a new bulb by inserting it into the socket.
7. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
OMD071059L
OMD071060L
■
Type A
■ Type B
Front fog light
Front fog light
Dedicated lamp