2012 HONDA PILOT light

´
The 7-pin trailer connector is needed
f or the trailer lights. To connect the
connector:Make sure the connector and the
socketarefreeof dirt,moisture,
or other f oreign material.
Open the socket lid by pulling it up. Ref er to the above illustrations f or
wiring inf ormation.
Insert the connector securely into
the socket.
Hook the retaining tab on the
inner side of the lid against the
retaining tab of the connector to
prevent disconnection during
operation.
3.
1. 2.
On Touring models On Touring models
T railer Connect or Socket s
Connect ing t he T railer Connect ors
Towing a Trailer
548
7-PIN TRAILER SOCKET
SMALL
LIGHT
(GREEN)
LEFT
TURN/
STOP
(RED)
BACK LIGHT
(YELLOW) B
CHARGE
(BLUE)
RIGHT
TURN/
STOP
(WHITE)
ELECTRIC
BRAKE
(BROWN/
WHITE)
GROUND
(BLACK)
7-PIN TRAILER CONNECTOR RETAINING TAB
LID
SOCKET RETAINING TAB
7-PIN TRAILER
CONNECTOR
Main MenuTable of Contents

The lights and brakes on your
vehicle and the trailer are working
properly.
Your vehicle tires and spare are in
good condition and properly
inf lated.
Towing perf ormance can be
af f ected by high altitude, high
temperature, or when climbing
steep grades. Theref ore, premium
f uel (premium unleaded gasoline
with pump octane number of 91 or
higher) is recommended when
towing more than 3,500 lbs (1,590
kg).
The trailer tires and spare are in
good condition and inf lated as
recommended by the trailer
maker.
When preparing to tow, and bef ore
driving away, be sure to check the
f ollowing:
The vehicle has been properly
serviced, and the suspension and
the cooling system are in good
operating condition.
The trailer has been properly
serviced and is in good condition.
All weights and loads are within
limits.
Thehitch,safetychains,andany
other attachments are secure.
Allitemsonandinthetrailerare
properly secured and cannot shif t
while you drive.
The trailer jumper harness is used to
install the controller f or the electric
trailer brakes. For more inf ormation,
see on page .
Insert the trailer brake f use into the
secondary under-hood f use box (see
page ).
544
634
On Touring models
Pre-T ow ChecklistT railer Jumper Harness
T railer Brake FuseTrailer Brakes
Towing a Trailer
Driving
549
BRAKE LIGHTS
(SKY BLUE)
GROUND
(BLACK)
BRAKE
(20A)
(BLUE)
ELECTRIC BRAKE
(BROWN/WHITE)
Main MenuTable of Contents

Use a nylon strap to attach your
vehicle to the recovery vehicle, and
caref ully take out the slack in the
strap. Once the strap is tight, the
recovery vehicle should apply f orce.
Remember that the recovery vehicle
needs good traction to avoid
becoming stuck, too.
You should never use a jack to try to
get unstuck. Your vehicle could
easily slip of f the jack and hurt you
or someone else.You may be able to safely tow a
lightweight trailer (such as a
motorcycle or small tent trailer) of f -
road if you f ollow these guidelines.
Do not exceed 1,000 lbs (450 kg)
or a tongue weight of 100 lbs (45
kg).
Stay on smooth, level dirt roads,
and avoid driving in hilly terrain.
Allow extra room f or starting,
stopping, and turning.
Slow down if you encounter bumps
or other obstacles.
Towing a Trailer Off-Road
Of f -Highway Driving Guidelines
Driving
555
Main MenuTable of Contents

This section explains why it is
important to keep your vehicle well
maintained and how to f ollow basic
maintenance saf ety precautions.
This section also includes
instructions on how to read the
Maintenance Minder messages on
the inf ormation display or multi-
inf ormation display (depending on
the model), and instructions for
simple maintenance tasks you may
want to take care of yourself.
If you have the skills and tools to
perf orm more complex maintenance
tasks on your vehicle, you may want
to purchase the service manual. See
page f or inf ormation on how to
obtain a copy, or see your dealer.U.S. Vehicles:
......................
Maintenance Saf ety . 558
.................
Maintenance Minder . 559
..............................
Fluid Locations . 574
......
Engine Compartment Covers . 575
........................
Adding Engine Oil . 576
Changing the Engine Oil and
...........................................
Filter . 577
..............................
Engine Coolant . 579
....................
Windshield Washers . 581
....
Automatic Transmission Fluid . 582
....................................
Brake Fluid . 584
....................
Power Steering Fluid . 585
....................................
Timing Belt . 585
.............................................
Lights . 586
..................
Dust and Pollen Filter . 593
................
Cleaning the Seat Belts . 593
.....................................
Floor Mats . 594
.................................
Wiper Blades . 595
...............................................
Tires . 599
...................
Checking the Battery . 607
.............................
Vehicle Storage . 608
..................................
Interior Care . 609
661
Maintenance
Maintenance, replacement, or
repair of emissions control
devices and systems may be done
by any automotive repair
establishment or individual using
parts that are ‘‘certif ied

µµ
µ
Lights Check the operation of
all the lights monthly. See page .
Brakes Check the f luid level
monthly. See page .
Tires Check the tire pressure
monthly. Examine the tread f or
wear and foreign objects. See page
. 584
600
586
Maintenance Minder
572
TM
Main MenuTable of Contents

Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.Open the hood.
If you need to change the
headlight bulb on the driver

Open the hood.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it
about one-quarter turn
counterclockwise. Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Remove the socket by turning it
one-quarter turn counterclockwise.
If you need to change the bulbs on
the driver

Push the new bulb straight into
the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Pull down the under cover f rom
the bumper caref ully.
Remove the f ive holding clips with
a f lat-tip screwdriver.
Pull the bulb straight out of its
socket. 1.
4. 5. 6. 2.
3.
Except LX models
Replacing a Front Fog L ight Bulb
Lights
588
BULB
SOCKET
SIDE MARKER LIGHT
UNDER COVER
HOLDING CLIP
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
Main MenuTable of Contents