2012 FORD MUSTANG lock

•5.4L DOHC 32V Supercharged V-8 engine with intercooler — 550
horsepower @ 6,200 rpm, 510 lb-ft torque @ 4,250 rpm SAE certified
•Low-restriction, cold air intake system
•SVT tuned 2.75” exhaust system with 4-inch tips
•Engine oil cooler
•TR-6060 6-speed manual transmission
•Twin disc clutch
•Anti-lock brake system
•
Front brakes: Brembo four-piston aluminum calipers with 14-inch vented
disc, slotted dust shields and high-performance friction material pads
•Rear brakes: include high-performance friction material pads
•SVT tuned front and rear suspension
•19 in. x 9.5 in. forged aluminum wheels (standard)
•P255/40ZR-19 front, P285/35ZR-19 rear Goodyear F1 tires (standard)
•19 in. x 9.5 in. front, 20 in. x 9.5 in. rear forged aluminum wheels
(optional)
•P265/40-19 front, P285/35-20 rear directional “R” compound tires
(optional)
ShelbyGT500Unique Features
5
2012 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

MANUAL 6-SPEED TRANSMISSION OPERATION
Using the Clutch
The manual transmission has a starter interlock that prevents cranking
the engine unless the clutch pedal is fully depressed.
To start the vehicle:
1. Make sure the parking brake is fully set.
2. Press the clutch pedal to the floor, then put the gearshift lever in the
neutral position.
3. Start the engine, then press the brake pedal and release the parking
brake.
4. Move the gearshift lever to 1st gear, then slowly release the clutch
pedal while slowly pressing on the accelerator.
During each shift, the clutch pedal must be fully pressed to the floor.
Failure to fully press the clutch pedal to the floor may cause increased
shift efforts, prematurely wear transmission components, or cause gear
clash or damage to the transmission. Make sure the floor mat is properly
positioned so it doesn’t interfere with the full extension of the clutch
pedal.
Note:If you attempt to shift when the drive wheels are spinning with a
loss of traction, it is possible to cause damage to the transmission. Do
not attempt to shift when the drive wheels do not have traction.
Do not drive with your foot resting on the clutch pedal or use the clutch
pedal to hold your vehicle at a standstill while waiting on a hill. These
actions will reduce the life of the clutch.
Your vehicle is equipped with a twin disc clutch. Due to the high
performance of the powertrain, a certain amount of noise from the
transmission is normal.
Driving your ShelbyGT500
10
2012 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

WRECKER TOWING
If you need to have your vehicle towed, contact your roadside assistance
center or a professional towing service.
It is recommended that your vehicle be towed with a wheel lift and
dollies or with flatbed equipment. When towing with a flatbed, 4x4
blocks must be used when loading/unloading your vehicle. Do not tow
with a slingbelt. Ford Motor Company has not approved a slingbelt
towing procedure.
Note:If the vehicle is towed by other means or incorrectly, vehicle
damage may occur.
Roadside Emergencies
19
2012 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

Flatbed
The diagram below illustrates the maximum ramp angle allowable to load
your vehicle on a flatbed. Vehicle damage may occur with greater angles.
1. 36 in. (91 cm) 4x4 loading block
2. 18 in. (45.72 cm) 4x4 loading block
3. 11.5° maximum
Roadside Emergencies
22
2012 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

WARNING:To reduce the risk of personal injury, make sure the
engine is cool before unscrewing the coolant pressure relief cap.
The cooling system is under pressure; steam and hot liquid can come
out forcefully when the cap is loosened slightly.
If you must remove the pressure relief cap or radiator cap (depending
upon engine application), follow these steps to avoid personal injury:
1. Before you remove the cap, turn the engine off and let it cool.
2. When the engine is cool, wrap a thick cloth around the cap. Slowly
turn cap counterclockwise until pressure begins to release.
3. Step back while the pressure releases.
4. When you are sure that all the pressure has been released, use the
cloth to turn it counterclockwise and remove the cap.
Coolant and Intercooler Refill Procedure
The following procedure should be used when refilling the cooling
system after it has been drained or become extremely low.
1. Remove the pressure relief cap from the coolant reservoir as
previously outlined.
2. Slowly add a50/50 mixtureof coolant and distilled water to the
coolant reservoir until the coolant level is at the “cold fill level” as listed
on the reservoir.
3. Reinstall the pressure relief cap.
4. Start and idle the engine until the upper radiator hose is warm (this
indicates the thermostat is open and coolant is flowing through the
entire system).
5. Shut the engine off and let it cool.
6. Remove the pressure relief cap from the coolant reservoir as
previously outlined.
7. Add a50/50 mixtureof coolant and distilled water to the coolant
reservoir until the coolant level is at the “cold fill range” as listed on the
reservoir.
8. Reinstall the pressure relief cap.
9. Check the coolant level in the reservoir before you drive your vehicle
the next few times (with the engine cool).
10. If necessary, add a50/50 mixtureof coolant and distilled water to
the coolant reservoir until the coolant level is at the “cold fill range” as
listed on the reservoir.
Maintenance
28
2012 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

ENGINE INFORMATION
Item Description
ConfigurationLongitudinally mounted, 90-degree V8, cast
aluminum cylinder block and cylinder heads
Bore x Stroke90.2 x 105.8 mm (3.55 x 4.165 in.)
Displacement5410 cc/330 cid
Compression ratio8.4:1
Horsepower550 horsepower @ 6200 rpm
Torque510 lb-ft torque @ 4250 rpm
Redline6250 rpm fuel shut-off
Specific output102 HP per liter
ValvetrainDual overhead chain-driven cams, roller finger
followers with hydraulic lash adjustment,
ovate-wire valve springs, four valves per cylinder
Fuel systemSequential electronic fuel injection
Mass air sensor105 mm (4.13 in.) circle
Throttle bodyTwin 60 mm (2.36 in.) diameter bore-
simultaneously open
PistonsForged aluminum
CrankshaftForged steel
Connecting rodsForged steel I-beam
SuperchargerEaton model 122, Roots-type
Exhaust manifoldsCast high-silicon, molybdenum iron
Exhaust systemDual stainless steel
Engine drivebelt routing
5.4L DOHC Supercharged V-8
Maintenance
34
2012 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

Value Shopping for Your Vehicle’s Maintenance Needs
Your dealership recognizes the competitive landscape of maintenance and
light repair automotive services. With factory-trained technicians, and
one-stop service from routine maintenance like oil changes and tire
rotations to repairs like brake service, check out the value your dealers
can offer.
Owner Checks and Services
Certain basic maintenance checks and inspections should be performed
by the owner or a service technician at the intervals indicated. Service
information and supporting specifications are provided in this owner’s
guide.
Any adverse condition should be brought to the attention of your dealer
or qualified service technician as soon as possible for the proper service
advice. The owner maintenance service checks are generally not covered
by warranties so you may be charged for labor, parts or fluids used.
Engine oil/coolant change intervals
Engine oil6 months or 7,500 miles (12,000 km)
(whichever comes first)
Engine coolant, initial
change6 years or 105,000 miles (168,000 km)
(whichever comes first)
Engine coolant, after
initial changeEvery 3 years or 45,000 miles (72,000 km)
Check every month
Engine oil level
Function of all interior and exterior lights
Tires for wear and proper pressure, including spare
Windshield washer fluid level
Check every six months
Battery connections; clean if necessary
Body and door drain holes for obstructions; clean if necessary
Cooling system fluid level and coolant strength
Door weatherstrips for wear; lubricate if necessary
Hinges/latches/outside locks for proper operation; lubricate if necessary
Parking brake for proper operation
Scheduled Maintenance Guide
38
2012 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)